• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2018.11a
• /
• pp.218-219
• /
• 2018

쌍동선형은 단동선형에 비해 안정성 및 저항성능이 우수하며 그 형상은 일반적으로 대칭 및 비대칭으로 구분한다. 이러한 쌍동선은 고속으로 운항하는 경우 선체사이의 파랑 중첩현상을 줄이기 위해 주로 비대칭선형을 사용한다. 또한, 중소형선박은 선미터널을 적용하여 추력효율을 향상시킨다. 본 연구에서는 비대칭 고속 쌍동선의 선미터널 입구영역의 경사각 변화에 따른 유체역학적 특성(저항성능, 항주자세, 압력분포)에 대한 수치해석 연구를 수행하였다. 수치해석은 상용프로그램 STAR CCM+를 이용하였다.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2017.11a
• /
• pp.232-233
• /
• 2017

In this research, tunnel stern was applied on the asymmetric high-speed catamaran to evaluate vessel's hydrodynamic performance by numerical method, and the tunnel stern types are distinguished by angle of inclination of tunnel exit region into 3cases ($0^{\circ}$, $3^{\circ}$ and $6^{\circ}$). Consequently, it is confirmed that the total resistances of tunnel stern which have $0^{\circ}$ of inclination are lower about 4.8-17.9% than the bare hull in the wide speed range, but those of $3^{\circ}$ and $6^{\circ}$ of inclination tunnel stern are higher than bare hull about 5-14% and 5-29%, respectively. On the other hand, trim angles of $0^{\circ}$ of inclination tunnel stern show similar trend with those of bare hull in whole ranges of FnV but those of $3^{\circ}$ and $6^{\circ}$ of inclination tunnel stern are stabilized and declined respectively after FnV=1.54. These phenomena indicated that increasing angle of inclination of tunnel exit region had negative influence on resistance performance, however, it could make vessel's operation performance better than bare hull.

• Proceedings of KOSOMES biannual meeting
• /
• 2017.11a
• /
• pp.9-9
• /
• 2017

• Proceedings of KOSOMES biannual meeting
• /
• 2017.04a
• /
• pp.260-260
• /
• 2017

• Journal of Korea Ship Safrty Technology Authority
• /
• v.17
• /
• pp.24-43
• /
• 2005

최근 우리나라 어선어업은 한중일 어업협정, 연안 어업자원 감소 및 연안오염 등 사회적, 환경적 변화가 급변하고 있어 이들을 고려한 어선 선형개발이 필요로 한다. 현재 우리나라의 어선 중 연안지역에서 조업하는 5톤 미만의 소형어선은 전체 어선 중 $65\%$ 이상으로 구성되어 있으나 선박의 크기가 작고 부가가치가 낮은 관계로 지금까지 전문적인 연구는 거의 없었던 것이 현실이다. 한편, 서$\cdot$남해 연안에서 작업 및 항해하는 연안어선들의 해양사고 발생율은 전체사고의 $69.6\%$로 매년 증가하고 있는 추세이다. 전체 어선 안전사고 중 부유폐어망, 로프 등이 추진기에 감긴 사고는 전체 사고의 $10.4\%$로 매년 증가하고 있다. 이에, 추진기 손상에 의한 어선 사고와 연관하여 추진기를 보호하기 위한 장치로서 물분사 추진기(Water-Jet), 펌프제트(Pump-Jet)장치들이 있으나 이들은 고가 수입품으로서 영세한 어민들의 소형어선에 장착하기에는 한계가 있어, 본 연구에서는 폐그물, 로프 등 해상 부유물에 의한 추진기 손상이 발생되지 않는 프로펠러 보호터널 부착 추진장치를 개발을 목적으로 한다. 프로펠러 부착 추진장치는 기존 선미를 수정하여 추진기를 선체 안쪽으로 배치하며 돌출되는 부분은 덕트로 보호하고 있으며 이러한 추진기는 워터제트 추진기와는 달리 가격이 싸고 그물이나 부유물에 걸리지 않고 고장 시 신속한 대응이 쉬워 소형 연안어선에 적합할 뿐만 아니라 그물, 부유물, 갯벌이 많은 국내의 서$\cdot$남해 연안에서 작업 및 항해 시 매우 유용할 것으로 판단된다. 본 연구는 `프로펠러 보호터널 부착 연안어선의 선형개발`을 최종목표로 수행하였으며, 연구개발 내용은 기존 소형 연안어선의 분류 및 특성 조사 연구, 프로펠러 보호터널형 선미 선형 개발, 기존 선형 및 보호터널형 선형의 모형시험, 개발선의 구조강도 특성, 프로펠러 설계 및 단독시험, 보호터널 부착 추진기의 효율 검증 및 개발 대상 어선의 조선공학적 제 계산, 설계도작성 등을 실시하였다. 주요 요소 기술로서는 프로펠러 보호터널 부착 선형의 모형시험을 통하여 선미선형을 개발하며 FRP판부재의 구조강도 특성을 분석하고 그 결과를 활용하여 4톤급 연안어선의 시제선을 건조하고 시운전을 통하여 주요성능을 확인하였다.

• Journal of the Society of Naval Architects of Korea
• /
• v.30 no.2
• /
• pp.66-75
• /
• 1993

Flow control devices, such as flow liners, are frequently introduced hi a cavitation tunnel in order to reduce the tunnel blockage effect, when a three-dimensional wake distribution is simulated using a complete ship model or a dummy model. In order to estimate the tunnel wall effect and to evaluate the effect of flow liners on the simulated wake distribution, a surface panel method is adopted for the calculation of the flow around a ship model and flow liners installed in a rectangular test section of a cavitation tunnel. Calculation results on the Sydney Express ship model show that the tunnel wall effect on the hull surface pressure distribution is negligible for less than 5% blockage and can be appreciable for more than 20% blockage. The flow liners accelerate the flow near the after body of the ship model, so that the pressure gradient there becomes more favorable and accordingly the boundary layer thickness would be reduced. Since the resulting wake distribution is assumed to resemble the full scale wake, flow liners can also be used to simulate an estimated full scale wake without modifying the ship model. Boundary layer calculation should be incorporated in order to correlate the calculated wake distribution with tole measured one.

• Journal of the Society of Naval Architects of Korea
• /
• v.30 no.4
• /
• pp.46-60
• /
• 1993

Accurate measurements of fluctuating pressure in the cavitation tunnel are necessary to predict vibration and noise intensities in full scale ship. In this paper, the results of an experimental study on fluctuating pressure induced by a cavitating propeller are presented and discussed. Extensive measurements at several propeller revolutions are made using the flat plate to understand controversial problems of the effects of propeller revolution in the cavitation tunnel. The analysis of the uncertainties in experimental measurements and results is used to estimate the errors in uniform flow.

• Journal of the Society of Naval Architects of Korea
• /
• v.33 no.1
• /
• pp.19-26
• /
• 1996

An experimental and computational study of the pressure fluctuation induced by a propeller on a hull surface was carried out with three ship models and seven model propellers. The fluctuation of pressure on a flat plate was measured at KRISO cavitation tunnel and calculated by a panel and lifting surface method(XForShip code). To extend the measurement data on the flat plate into that on complex hull forms, the correction factor was determined as a ratio of the solid boundary factor(SBF). The computation of pressure fluctuation around complex hull forms was also performed to make the full scale prediction and compared with the corrected experimental data. The calculated values agreed well with the compensated experimental data and it was found that the correction factor was about 0.65-0.7.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2003.05a
• /
• pp.16-20
• /
• 2003

Recently, The fast change of fishing boat fishery surrounding environment is connected by request of fan shape development that meet in restructuring of existing fishing boat fishery and new community, economical surrounding. In southern sea district along the coast work and district along the coast fishing bats that sail to exposed propeller fishing net, rope etc.. cold real condition that accident is increasing every year. This study is thing which analyze main performance of minuteness water jet type district along the coast fishing boat through model examination to propeller protection tunnel sticking district along the coast fishing boat that correct existing stem shape for marine accident prevention of district along the coast fishing boat in viewpoint such as ideal and examines.

• Journal of the Society of Naval Architects of Korea
• /
• v.39 no.2
• /
• pp.1-10
• /
• 2002

Hull-propeller-rudder interactions are studied by the iterative computational procedures. Hull effects on the propeller are reflected through the effective velocities computed by the vortex ring method which used the measured nominal wake as input data. A potential based panel method has been developed to solve the propeller-rudder interactions using the obtained effective velocities. Steady flow characteristics around the rudder surface can be obtained by computing the induced velocities on the rudder by the propeller and vice versa are computed by the iterative manner until the converged solutions are obtained. Flow characteristics around the propeller and the rudder are measured by Laser Doppler Velocimetry(L.D.V.) in large cavitation tunnel at Samsung Heavy industries. The gap flow model is adopted to solve the characteristics of the horn rudder. Numerical results are compared with the experimental values and the computed velocity fields and pressure distributions with rudder angle on the horn rudder surface show good agreement with measured ones in large cavitation tunnel.