• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.7
• /
• pp.722-729
• /
• 2013

This paper presents the influence on the transmission characteristics of dimensional tolerances of rectangular waveguides usually used as a low-loss transmission line in the millimeter-wave band. We derived the Green's functions of the waveguide with eigenfunction expansion method. The reflection coefficient of the waveguide with a post is calculated by using internal impedance in order to investigate the influence of dimensional tolerances of the waveguide. In order to check the validity of the theoretical analysis, the calculated reflection coefficients are compared with the measured results.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.2
• /
• pp.260-267
• /
• 2014

In this paper, the unit cell of LH structure using microstrip transmission line and chip capacitor is devised, and the reactive components of equivalent circuit are extracted from the proposed unit cell. And then, we have analyzed for the unit cell parameters and applied the characteristics to the wideband high pass filter design. This filter cascading several unit cells with high pass property has been implemented on microstrip transmission line, and the performance has been the band rejection characteristics of 62.9 dB in the stop band to 0~2.18 GHz and less than the insertion loss of 1.17 dB in the pass band from 3.0G Hz to 12.75 GHz.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.3
• /
• pp.540-548
• /
• 2007

The parer proposes a power factor correction high efficiency PWM single-phase rectifier. Its good characteristics such as simple PWM control, low switch stress, and low VAR rating of commutation circuits make the proposed rectifier very suitable for various unidirectional power applications. In addition, the proposed rectifier consists of three boost-converter-type IGBT modules with the switching devices located at the bottom leg of the rectifier scheme, which also enables the use of the same power supply in both control and gate driver, thus resulting in simple control and power circuit structure. The detailed principle of operation and experimental results are also included. In particular, the design guide line is also suggested to make the circuit design of the proposed rectifier easy and fast.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.10
• /
• pp.65-70
• /
• 2008

We design and fabricate the 94 GHz Coplanar waveguide(CPW)-to-rectangular waveguide transition that is transmits signal smoothly between the CPW, which is a popular transmission line of the planar circuits, and rectangular waveguide for the 94 GHz transceiver system. The proposed transition composed of the unilateral fin-line taper and open type CPW-to-slot-line transition is based on the hard and inflexible sapphire for the flip-chip bonding of the planar MMICs using conventional MMIC technology. We optimize a single section transition to achieve low loss by using an EM field solver of Ansoft's HFSS and fabricate the back- to-back transition that is measured by Anritsu ME7808A Vector Network Analyzer in a frequency range of $85{\sim}105$ GHz. From the measurement and do-embedding CPW with 3 mm length, an insertion and return loss of a single-section transition are 1.7 dB and more an 25 than at 94 GHz, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.11
• /
• pp.1217-1223
• /
• 2007

Advanced microwave absorbers for wide oblique incidence angles are required in many applications including wireless communication or vehicle identification in ITS(Intelligent Transport System) where 5.8 GHz DSRC(Dedicated Short Range Communication) system is applied. In this study, two-layered microwave absorber(with a laminate structure of dielectric/magnetic composites) has been designed for the achievement of low reflection coefficient over wide incidence angles at 5.8 GHz. Iron flake particles are used as the filler in the absorbing layer, and the magnetic composite sheet exhibits high magnetic loss due to ferromagnetic resonance in gigahertz frequencies. The surface layer of low dielectric constant containing small amount of carbon black is used as the impedance transformer. On the basis of transmission line theory, the reflection loss has been calculated for the two-layer structure with variation of incident angles for both TE(Transverse Electric) and TM(Transverse Magnetic) polarizations. At the optimum thickness of the composite layers, a low value of reflection loss(less than -10 dB) has been predicted for wide incidence angles up to $55^{\circ}$ which is in good agreement with the measured value determined by free-space measurement.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.3 s.94
• /
• pp.246-252
• /
• 2005

A RF microstrip balun having low transmission loss for the balanced receiving dipole antenna is designed and fabricated using a three-section Wilkinson divider and two 3-dB quadrature couplers. It considers two types of the three-section Wilkinson dividers, the Cohn's optimum three-section structure and the miniaturized three-section structure, for wideband power splitting. Also, two 3-dB quadrature couplers for 180 degrees of phase difference adopt a twist-wire coaxial cable. The fabricated first balun having the Cohn's optimum three-section Wilkinson divider has 0.5 dB of transmission loss, $\pm$0.2 dB of amplitude imbalance, and 180$\pm$2.3 degrees of phase imbalance over 400 to 1000 MHz by measurement. The second one using the miniaturized three-section Wilkinson divider shows 1.0 dB of transmission loss, $\pm$0.7 dB of amplitude imbalance, and 180$\pm$8.8 degrees of phase imbalance over the same frequency band.

• Journal of the Korean Magnetics Society
• /
• v.16 no.6
• /
• pp.300-304
• /
• 2006

The varied heating temperatures were used for magnetic core materials, which nano sized ${\alpha}-Fe$ crystalline was created in nanocrystalline Fe-Si-B-Nb-Cu materials, with hish permeability and low power loss. The highest permeability and lowest power loss were obtained to the specimen heat-treated at $510^{\circ}C$. The signal transmission characteristics of inductive coupler, which was manufactured by using the magnetic core materials prepared in this study, at low frequency range, was influenced strongly by magnetic property of magnetic core materials as this result is corresponding to the permeability as a function of heat treatment temperature, as well, it was improved by impedance matching at high frequency range. Over $500{\mu}m$ of air gap in coupler is required to maintain the magnetic properties without magnetic saturation on the subterranean line transferred hish current of 300 A. The inductive coupler for PLC, which has an attenuation characteristics of less than 5dB, was manufactured using nano-crystalline magnetic core materials through the above mentioned research results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.8
• /
• pp.694-700
• /
• 2009

In this paper, we propose a RFID tag antenna with low performance degradation due to nearby dielectric materials. The proposed antenna is designed to be appropriate for ink printing fabrication. The antenna is designed to operate in UHF band of $860{\sim}960$ MHz. The antenna uses a T-matching network in the middle of the main body and two parasitic patches in vicinity for complex conjugate matching with a commercial tag chip. In addition, the two parasitic patches induce currents at different dielectric constants of nearby dielectric materials. This can minimize the performance degradation due to nearby dielectric materials. The measured results show the half power matching bandwidth from 844 MHT to 1,268 MHz. It exhibits the reading distance of about 3.5 m in free space when the tag antenna is used with the commercial reader antenna (transmitting power of 20 dBm and the reader antenna gain of 6 dBi). When the tag is attached on dielectric materials of wood and FR4, the resulting reading distances are 2.61 m and 2.51 m, respectively.

• The KIPS Transactions:PartC
• /
• v.8C no.5
• /
• pp.629-636
• /
• 2001

Network is changed from voice-based network into multimedia-based network by development of communication technology and multimedia service. We need a large bandwidth for multimedia service. The optical fiber is a more suitable medium than existing copper-based cable for large bandwidth. But, it is so expensive than copper-based cable. So, Minimizing total cost becomes a more important concept. In order to construct a minimum cost network, we have to consider existing conduits in network. On the other hand, optical fiber network allows that larger amount of traffic can be transmitted than copper-based network does. However, a failure of a node or link can make a serious damage to the network service. Thus, we have to get multiple paths to support continuous service even if a loss of failure occurs in some point of the network. The network survivability problem is to design the network that can provide reliable service to customers anytime with minimum total cost. In an existing solution of the network survivability problem with conduits, a conduit is considered only one time. But, the conduit is reusable if the network satisfies the required survivability. Proposed algorithm can more effectively considered already existed conduit. Network survivability and edge cost is predetermined. The proposed algorithm finds the best solution by conduit sharing within the limits of network survivability. According to the simulation result, the proposed method can decrease 7% of total cost than an existing method by effective conduits adaption.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.11 no.5
• /
• pp.44-52
• /
• 1997

Electronic circuits with semiconductor and IC are very weak against the surge voltage and currents. The surge protective devices for electronic circuit and AC power lines are becoming more widely used. It is possible to give rise to the malfunction of the earth leakage circuit breaker(ELB) due to the operation of surge protective devices, and the interruption of AC power lines on account of the malfunction of the ELB brings about several disadvantages such as low operation efficiency and reliability of electronic and informational systems, economical loss, and etc. The aim of the present work is to investigate the dead operation characteristics of the ELB against the surge voltages. The impulse generator of 10[kV) in an 1.2/ 50[~) voltage waveform was fabricated. The dead operation characteristics of the ELB applied by surge voltages were measured under the conditions of KS C 4613 and the test circuit with a varistor. As a consequence, the peak value of the zero-phase sequence circuit of the ELB is increased as the surge voltage and stray capacitance increase. All of the ELBs used in this work were satisfied with the lightning impulse dead operation test condition defined in KS C 4613. However one specimen only did not bring about dead operation in the condition of the test circuit with a varistor. There is high possibility that a large portion of the ELB installed at the AC power lines with the surge protective devices bring about the dead operation.