• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.5
• /
• pp.510-519
• /
• 2013

In this study, the spray characteristics of a pressure swirl atomizer classified into a liquid sheet-type swirl nozzle for Urea-SCR system were investigated experimentally with the variation of injection pressure. The length to diameter ratio ($l_o/d$) of the nozzle was 3.1, and the swirler was set inside the nozzle tip to give injecting fluid angular momentum. The injection duration of the nozzle was controlled by PWM (pulse width modulation) modes. The development processes of the spray were imaged by a 2-D PIV system, and the change of spray angle was measured. The atomization characteristics, including axial velocity and SMD, were measured using a 2-D PDA system with the injection pressures at room temperature and ambient pressure conditions. As the experimental results, the injection pressure had a significant impact on the spray structure showing a different shape around the spray leading edge, and the smaller SMD was observed with increasing injection pressures, which was similar to that of the previous work.

• Composites Research
• /
• v.18 no.4
• /
• pp.35-43
• /
• 2005

In resin transfer molding(RTM), race-track effects and non-uniform fiber volume fraction may cause undesirable resin flow patterns and thus result in dry spots, which affect the mechanical properties of the finished parts. In this study, a real time RTM control strategy to reduce these unfavorable effects is proposed. This control rule is accomplished by means of the permeability mapping and pressure regulation. Through numerical simulations, the validity of the proposed scheme is demonstrated.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.303-306
• /
• 2011

An experimental study has been conducted to investigate the effects of an ultrasonic standing-wave field to the behavior of methane/air premixed flame. Visualization technique utilizing the schlieren method was employed for the observation of premixed flame behavior. The shape of flame front and local flame velocity were measured according to the variation of reactants pressure and chamber opening/closing condition. The flame front was distorted and severely deformed to a lotus-type flame by the interaction of ultrasonic standing-wave and the reflection wave coming from an end wall of reactor.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.4
• /
• pp.836-845
• /
• 2017

Due to the development of endoscopic technology, endoscopic diagnosis and procedures have been actively performed. However, due to the increase in colorectal cancer and the effect of government's early cancer screening project, the number of endoscopic diagnosis and procedures has increased, thus medical accidents such as perforation and bleeding are increasing. Therefore, efforts to reduce such medical accidents are needed. In this paper, we propose a method to provide the direction information of the endoscope and the force applied to the probe in real time. We also propose and evaluate an interpolated complementary filter considering the very slow movement of the endoscope probe. The proposed interpolated complementary filter showed 34.6% and 27.6% performance improvement. The expected user interface for applying the proposed method to the endoscopic system is also presented. This shows that the proposed method is applicable to endoscopy system.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.40 no.1
• /
• pp.98-102
• /
• 1995

Popped popcorn generally have a regular popping direction and typical shape. But the reason and mechanism are not clear yet. This experiment was carried out to investigate the shape moulding factor of popped popcorn. Pericarp thickness of tip-cap section of kernels is slightly thicker than that of top section and this fact provides the important information to the reason. Popping starts when the moisture pressure of heated popcorn is increased and reaches at the critical pressure. Therefore, in the same moisture pressure conditions, top sections are bursted first because their pericarp section is thinner than that of tip-cap section. At the very moment tip-cap sections pull down the top sections of peri carp as bi-metal does. So kernels which removed tip-cap section showed the irregular popping shape because they lost the tip-cap pericarp function. How-ever, kernels which removed embryo showed the typical popping shape but their popping volume was small due to emition and shortage of critical moisture pressure. But kernels which removed the whole pericarp and top pericarp were not popped at all because moisture was entirely emitting out of kernels. These results suggest that the shape moulding factor of popped popcorn is the pericarp thickness differences between the top and tip-cap section of kernels.

• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.1
• /
• pp.57-64
• /
• 2003

The characteristics of fuel spray have an important effect on engine performance such as power, specific fuel consumption and emission because fuel spray controls the mixing and combustion process in an engine. Therefore, if the characteristics of fuel spray can be measured, they can be effectively used for improving engine performance. The major factors controlling fuel spray are injection pressure, ambient pressure and engine speed. In this study, the experiment is performed in a high temperature and high pressure chamber. In experiments, spray tip penetration, spray angle and spray tip velocity are measured at various injection pressure (10 and 14 MPa), ambient pressure(3,4 and 5 MPa), fuel pump speed(500, 700 and 900 rpm). Experimental results are useful for deriving an experimental spray equation and design an optimal engine. The results showed that injection pressure, ambient pressure and fuel pump speed are important factors influencing on the characteristics of spray. 1) Injection pressure influences on the characteristics of spray. That is, as injection pressure is increased, spray angle is decreased but spray penetration and spray tip velocity is increased. 2) Spray angle and spray penetration are increased as fuel pump speed is increased.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.5
• /
• pp.182-190
• /
• 1998

Behaviour of ultra-high pressure diesel spray in a constant-volume pressure chamber was studied with injection pressure ranging from 20 to 160㎫. Sprays were observed by the right angle scattering method. As a result, the spray tip penetration is first proportional to a time, and after that, it is proportional to 0.52 of the time during at the time of injection pressure and back pressure increase. An empirical correlation was made for the parameters of injection pressure, air-fuel density ratio, spray tip distance, spray angle, jet angle of spray and max. spray width.

• Journal of ILASS-Korea
• /
• v.6 no.4
• /
• pp.39-48
• /
• 2001

The Gasoline Direct Injection(GDI) system has been highlighted due to the improvement of fuel consumption and the control of exhaust emission from gasoline engines. Main purpose of the present study is to measure spray characteristics of GDSI for real engine application. We have investigated experimentally spray tip penetration, spray angle, tip velocity and spatial spray distribution. Counter-rotating vortex grown on the spray surface plays an important role in the spray characteristics. Accordingly the spray tip penetration and tip velocity do not excess 50mm, 20m/s respectively, under 0.6MPa ambient pressure. the spray cone angle of GDSI have a same tendency to a simplex swirl atomizer.

• Journal of Advanced Marine Engineering and Technology
• /
• v.18 no.3
• /
• pp.68-77
• /
• 1994

TIG welding process is applied for the active metal such as aluminum and titanium, also sometimes for overlay welding of superalloy. However the welding speed to be applied is very low because of the unstable bead formed in the region of high current and high welding speed. The present study was carried out to examine the basic phenomena of high speed TIG melt run welding by the 2% Th - W electrode(dia.3.2mm) of various tip shapes.

• Journal of Power System Engineering
• /
• v.14 no.2
• /
• pp.16-21
• /
• 2010

분사된 연료의 미립화(atomization), 증발(evaporation), 그리고 혼합기형성과정(mixture formation process)이 디젤엔진의 착화 및 연소특성에 영향을 미치기 때문에, 디젤엔진 내에 분사된 연료의 구조해석으로부터 일련의 과정, 즉 고압분사, 분열(breakup), 미립화, 그리고 주위기체의 난류 도입(entrainment)에 관한 연구$^{1-3)}$는 꾸준히 행해져왔다. 본 연구는 증발디젤분무의 구조해석으로부터 디젤충돌분무의 혼합기형성과정을 조사한다. 주위기체의 밀도는 실험변수로서 선택하였고, $5.0kg/m^3$에서 $12.3kg/m^3$까지 변화시켰다. 그리고 소형고속디젤엔진에 있어서 연료분사초기의 상태의 고온 고압 설정이 가능한 정적용기를 사용했다. 주위 온도와 연료분사압력은 각각 700K 및 72MPa로 일정하게 유지했다. 충동증발분무의 액상과 기상의 이미지는 엑시플렉스형광법으로 동시 계측하였다. 실험결과로서 주위기체의 밀도가 높을수록 충돌분무의 선단도 달거리가 주위기체의 항력으로 인하여 감소하였다.