• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.1
• /
• pp.40-47
• /
• 2009

This paper presents the method of measuring the feedback interference channel, which is developed between the transmit and receive antennas of a wireless repeater by receiving the transmit signal at the receive antenna of the identical repeater, and experiment results obtained by analyzing the measurements. This experiment uses 2 GHz WCDMA signal and is carried out near a highway. The high-speed mobiles on highways cause reflected signals with high Doppler frequencies and large energy. In order to characterize the feedback channel, the power delay profile and the scattering function are estimated by identifying the delay spread, the Doppler spread, the number of fingers, and the attenuation with delay. Since the feedback interference channel is constructed between the fixed TX and RX antennas, which is dependent upon the multipaths developed by moving or fixed objects around the antennas, the channel shows different properties comparing to the conventional channels between the base station and the mobile station. Therefore, the results presented in the paper are expected to provide guidelines for designing and evaluating wireless repeater systems.

• Journal of IKEEE
• /
• v.13 no.4
• /
• pp.96-102
• /
• 2009

We investigate the characteristics of RJ (random jitter) in an analog fiber-optic link employing a MZM (Mach-Zehnder modulator) and an EDFA (Erbium-doped fiber amplifier). RJ has been measured using two methods, one of which derived from the noise spectrum of a RF spectrum analyzer and the other from the histogram data of a sampling oscilloscope. If the optical power and/or the RF power input to the MZM increase, RJ decreases due to the output signal power increase. For the optical link without EDFA, the minimum RJ is about 1 ps at an RF power of 10 dBm and an optical power of 8 dBm measured using the noise spectrum method. For the optical link with an EDFA, RJ decreases toward a jitter floor as the EDFA gain increases. If the gain increases further, it has been observed that RJ increases from the minimum. If the EDFA gain is fixed, RJ is smaller for the case of larger optical input power. As the EDFA gain increases, RJ reduction rate becomes greater for the case of lower optical input power.

• Journal of Soil and Groundwater Environment
• /
• v.10 no.5
• /
• pp.52-60
• /
• 2005

The conceptual model of under-sampled study area will include a great amount of uncertainty. In this study, we investigate the applicability of Markov chain model in a spatial domain as a tool for minimizing the uncertainty arose from the lack of data. A new formulation is developed to generalize the previous two-dimensional coupled Markov chain model, which has more versatility to fit any computational sequence. Furthermore, the computational algorithm is improved to utilize more conditioning information and reduce the artifacts, such as the artificial parcel inclination, caused by sequential computation. A generalized 20 coupled Markov chain (GCMC) is tested through applying a hypothetical soil map to evaluate the appropriateness as a substituting model for conventional geostatistical models. Comparing to sequential indicator model (SIS), the simulation results from GCMC shows lower entropy at the boundaries of indicators which is closer to real soil maps. For under-sampled indicators, however, GCMC under-estimates the presence of the indicators, which is a common aspect of all other geostatistical models. To improve this under-estimation, further study on data fusion (or assimilation) inclusion in the GCMC is required.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.1
• /
• pp.135-141
• /
• 2018

In this paper, we describe design and implementation of optimal smart home control system. Recent developments in technologies such as sensors and communication have enabled the Internet of Things to control a wide range of objects, such as light bulbs, socket-outlet, or clothing. Many businesses rely on the launch of collaborative services between them. However, traditional IoT systems often support a single protocol, although data is transmitted across multiple protocols for end-to-end devices. In addition, depending on the manufacturer of the Internet of things, there is a dedicated application and it has a high degree of complexity in registering and controlling different IoT devices for the internet of things. ARIoT system, special marking points and edge extraction techniques are used to detect objects, but there are relatively low deviations depending on the sampling data. The proposed system implements an IoT gateway of object based on OneM2M to compensate for existing problems. It supports diverse protocols of end to end devices and supported them with a single application. In addition, devices were learned by using deep learning in the artificial intelligence field and improved object recognition of existing systems by inference and detection, reducing the deviation of recognition rates.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.2
• /
• pp.185-195
• /
• 2018

As machines have been automated in the field of industries in recent years, it is a paramount importance to manage and maintain the automation machines. When a fault occurs in sensors attached to the machine, the machine may malfunction and further, a huge damage will be caused in the process line. To prevent the situation, the fault of sensors should be monitored, diagnosed and classified in a proper way. In the paper, we propose a sensor fault detection scheme based on SVM and CNN to detect and classify typical sensor errors such as erratic, drift, hard-over, spike, and stuck faults. Time-domain statistical features are utilized for the learning and testing in the proposed scheme, and the genetic algorithm is utilized to select the subset of optimal features. To classify multiple sensor faults, a multi-layer SVM is utilized, and ensemble technique is used for CNN. As a result, the SVM that utilizes a subset of features selected by the genetic algorithm provides better performance than the SVM that utilizes all the features. However, the performance of CNN is superior to that of the SVM.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.41 no.4
• /
• pp.55-62
• /
• 2004

In this paper, we have developed a portable acceleration measurement system to measure acceleration signals during walking and a gait analysis algorithm which can evaluate gait regularity and symmetry and estimate gait parameters automatically. Portable acceleration measurement system consists of a biaxial accelerometer, amplifiers, lowpass filter with cut-off frequency of 16Hz, one-chip microcontroller, EEPROM and RF(TX/RX) module. The algerian includes FFT analysis, filter processing and detection of main peaks. In order to develop the algorithm, eight hemiplegic patients for training set and the other eight hemiplegic patients for test set are participated in the experiment. Acceleration signals during 10m walking were measured at 60 samples/sec from a biaxial accelerometer mounted between L3 and L4 intervertebral area. The algorithm, detected foot contacts and classified right/left steps, and then calculated gait parameters based on these informations. Compared with video data and analysis by manual, algorithm showed good performance in detection of foot contacts and classification of right/left steps in test set perfectly. In the future, with improving the reliability and ability of the algerian so that calculate more gait Parameters accurately, this system and algerian could be used to evaluate improvement of walking ability in hemiplegic patients in clinical practice.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.7
• /
• pp.29-38
• /
• 2009

In this paper, a high performance pipelined computing design of parallel multiplier-temporal buffer-parallel accumulator is present for the convolution-based non-cascaded architecture aiming at the real time Discrete Wavelet Transform(DWT) processing. The convolved multiplication of DWT would be reduced upto 1/4 by utilizing the filter coefficients symmetry and the up/down sampling; and it could be dealt with 3-5 times faster computation by LUT-based DA multiplication of multiple filter coefficients parallelized for product terms with an image data. Further, the reutilization of computed product terms could be achieved by storing in the temporal buffer, which yields the saving of computation as well as dynamic power by 50%. The convolved product terms of image data and filter coefficients are realigned and stored in the temporal buffer for the accumulated addition. Then, the buffer management of parallel aligned storage is carried out for the high speed sequential retrieval of parallel accumulations. The convolved computation is pipelined with parallel multiplier-temporal buffer-parallel accumulation in which the parallelization of temporal buffer and accumulator is optimize, with respect to the performance of parallel DA multiplier, to improve the pipelining performance. The proposed architecture is back-end designed with 0.18um library, which verifies the 30fps throughput of SVGA(800$\times$600) images at 90MHz.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.2
• /
• pp.131-141
• /
• 2004

For geotechnical applications, engineers use data obtained from a site investigation to interpret the structure and potential behavior of the subsurface. In most cases, these data consist of samples that represent 1/100,000 or less of the total volume of soil. These samples and associated field and lab testing provide the information used to estimate soil parameter values. The resulting values are estimated ones and there exists some likelihood that actual soil conditions are significantly different from the estimates. This may be the case even if the sampling and interpretation procedures are performed in accordance with standard practice. Although these efforts have been made to characterize the uncertainty associated with geotechnical parameters, there is no commonly accepted method to evaluate quantitatively the quality of an investigation plan as a whole or the relative significance of individual sampling points or potential sampling points.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.22 no.2
• /
• pp.192-197
• /
• 2012

With the advent of DNA microarray technologies, researches for disease diagnosis has been actively in progress. In typical experiments using microarray data, problems such as the large number of genes and the relatively small number of samples, the inherent measurement noise and the heterogeneity across different samples are the cause of the performance decrease. To overcome these problems, a new method using functional modules (e.g. signaling pathways) used as markers was proposed. They use the method using an activity of pathway summarizing values of a member gene's expression values. It showed better classification performance than the existing methods based on individual genes. The activity calculation, however, used in the method has some drawbacks such as a correlation between individual genes and each phenotype is ignored and characteristics of individual genes are removed. In this paper, we propose a method based on the ensemble classifier. It makes weak classifiers based on feature vectors using subsets of genes in selected pathways, and then infers the final classification result by combining the results of each weak classifier. In this process, we improved the performance by minimize the search space through a filtering process using gene-gene interaction information and the mRMR filter. We applied the proposed method to a classifying the lung cancer, it showed competitive classification performance compared to existing methods.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.25 no.4
• /
• pp.355-362
• /
• 2012

Remaining useful life(RUL) prediction of a system is important in the prognostics field since it is directly linked with safety and maintenance scheduling. In the physics-based prognostics, accurately estimated model parameters can predict the remaining useful life exactly. It, however, is not a simple task to estimate the model parameters because most real system have multivariate model parameters, also they are correlated each other. This paper presents representative methods to estimate model parameters in the physics-based prognostics and discusses the difference between three methods; the particle filter method(PF), the overall Bayesian method(OBM), and the sequential Bayesian method(SBM). The three methods are based on the same theoretical background, the Bayesian estimation technique, but the methods are distinguished from each other in the sampling methods or uncertainty analysis process. Therefore, a simple physical model as an easy task and the Paris model for crack growth problem are used to discuss the difference between the three methods, and the performance of each method evaluated by using established prognostics metrics is compared.