• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.2
• /
• pp.119-128
• /
• 2010

The hygrothermal effect on the strength of composite single-lap bonded joints were investigated. The specimens were manufactured in four different manufacturing methods and tested in three different environmental conditions. An interesting result is that the strengths of the joints in the elevated temperature and wet (ETW) conditions were found to be 11 ~ 23% higher than those in the room temperature and dry (RTD) environment. In contrast, the strengths of the joints in the cold temperature and dry (CTD) condition decrease by 8 ~ 21% compared to those in the RTD environment except for cobonded joint. The difference in the strength by testing environments is mainly attributed to the change of the material properties of adhesive by temperature and moisture.

• Composites Research
• /
• v.24 no.4
• /
• pp.48-54
• /
• 2011

The effect of moisture contents by salt water on the strength of composite single-lap bonded joints is investigated. The specimens were manufactured in an autoclave by secondary bonding and immersed in the 3.5% salt water of $71^{\circ}C$ for different durations to get various moisture contents; 0, 0.2, 0.5, 1.0, and 2.0%(saturation). A total of 80 joint specimens were tested for 5 different moisture contents and 2 temperature environments. Test results show that while the joint strengths after the saturation of moisture decrease compared to those of dry ones, the strengths of the pre-saturated joint up to 1.0% of moisture content increase in both room and elevated temperature conditions. It is also shown that the strengths of joints tested in elevated temperature are slightly higher than the strength in room temperature by 2-5% until the moisture content reaches 1 %. In contrast, the high temperature strength of the saturated joint is about 5% lower than the room temperature strength.

• Composites Research
• /
• v.23 no.2
• /
• pp.10-16
• /
• 2010

$Al_2O_3$ fiber and SiC particle hybrid metal matrix composites (MMCs) were manufactured by squeeze casting method investigated for their tribological properties. The pin specimens had different ratios of fiber to particle content but their total weight fraction was constant at 20 wt. %. Tribological tests were performed with a pin-on-disk friction and wear tester. The investigation of the dry tribological characteristics of hybrid MMCs were carried out at room temperature and elevated temperature of$100^{\circ}C$ and$150^{\circ}C$. The morphologies of worn surfaces were examined by scanning electron microscope (SEM) to observe tribological characteristics and investigate wear behavior. The results revealed that the wear resistance improved with the content of SiCp increased of the planar random (PR) MMCs at room temperature. At the elevated temperature, it revealed that the wear resistance of normal (N) MMCs was superior to that of the PR-MMCs due to PR-fibers were easily pulled out holistically from the worn surface. Meanwhile, the coefficient of friction decreased with the temperature increasing.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.11
• /
• pp.1115-1122
• /
• 2010

The main objective of this study is to experimentally investigate the effect of adhesive thickness and environmental conditions on the failure and strength of sandwich-to-laminate bonded joints. Three different adhesive thicknesses (t=0.2, 2 and 4 mm) and two different environmental conditions were considered. Environmental conditions include the RTD(room temperature and dry condition) and ETW(elevated temperature and wet condition). Test results show as the adhesive thickness increases from 0.2 mm to 2 and 4 mm, the joint strength decreases 16 and 30%, respectively. Regarding the effect of environmental conditions, except for one case, the joint strength in the ETW conditions turned out to be 12% higher than those in the RTD conditions. In the joints with adhesive thickness of 0.2 mm, remarkable difference from RTD condition was not found.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.2
• /
• pp.111-117
• /
• 2019

An experimental study on the welding part of a heat transfer plate that constitutes the lightweight and high efficiency recuperator is presented in this paper. In particular, to find out the service life of the welded part, fatigue characteristics were determined through experiments. Experiments were carried out on two materials (STS347, AL20-25 + nb), which are selected as the material of the recuperator; further, the specimens were manufactured through the methods used for actual fabrication and the standards recommended by ASTM. To evaluate the mechanical properties of the specimens at room and high temperature, MTS-810 was used in a high-temperature furnace. The tensile test was carried out at room and high temperatures for each specimen. The fatigue test was carried out by setting the load ratio corresponding to 50%, 40%, 30%, 20%, and 10% of the tensile strength at the stress ratio of 0.1. Finally, the fatigue life characteristics obtained by the experiment were compared with the stresses owing to the load generated in the operating conditions of the recuperator, and the lifetime of the welds was evaluated to prepare for the operation time required by the UAV.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.1
• /
• pp.76-81
• /
• 2009

A nonlinear pressure controller to actively regulate the thrust of a solid propulsion system is presented. To compensate for the parametric uncertainties with respect to the chamber pressure induced by changing nozzle throat area, Lyapunov-based parameter adaptation method has been applied. In order to verify the effectiveness of the proposed control method, the experiments were carried out using the cold gas test equipment that can simulate the operating environment of variable thrust solid propulsion system. The experiment results show that the nonlinear pressure controller has better performance than conventional P and PI controller.

• Aerospace Engineering and Technology
• /
• v.11 no.2
• /
• pp.122-128
• /
• 2012

Many of the liquid rocket engines use a hypergolic igniter with rupture disc ends located in the combustion chamber ignition line. In this study, the flow coefficient tests of the igniter, which have a solenoid valve upstream, were performed. The tension-type rupture discs for radial and circumferential scores and the igniter with them were tested using water at room temperature. The effects of the score, flow rate, the disc thickness, gas pocket and the solenoid valve on the coefficient were analyzed.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.13-13
• /
• 2009

현재 열간단조 금형을 제작함에 있어 육성용접을 실시하는 방법이 금형강 STD61, STD11 등으로 제작하는 방법에 비해 보수나 비용적인 측면에서 이점을 가지고 있기 때문에 점차적으로 증가하고 있는 추세이다. 열간단조 공정에서 금형은 $1000^{\circ}C$이상의 고온재료와 반복접촉하게 된다. 이때 이형제의 사용은 급속냉각 및 급속가열의 열피로를 가속시킨다. 또한, 금형은 반복충격에 의한 기계적 피로를 받게 된다. 이러한 금형의 사용환경을 고려한 FCW는 종래 고가의 $2.8{\sim}3.2{\Phi}$인 외국산 FCW를 사용하였으나 이를 대체한 $3.2{\Phi}$ 태경 FCW가 국내에서 개발되었다. 하지만 개발된 FCW를 사용하여 제작된 금형의 수명이 부족한 현상이 발생하였다. 이에 금형의 수명을 연장시킬 수 있는 내균열성 및 내열충격성을 확보한 태경 FCW의 개발과 개발된 FCW의 성능평가가 요구되었다. 특히 열간단조 금형에 있어서 중요한 내열충격성의 경우 가열과 냉각의 반복 Cycle에 의한 Thermal shock의 평가가 대부분이며 높은 Cycle로 인해 많은 시간이 걸리며, 또한 가열과 냉각을 오갈 수 있는 고가의 시험장치가 요구된다. 그러므로 개발된 FCW 육성용접부의 내균열성 및 내열충격성을 평가할 수 있는 방법에 대한 연구와 특히 내열충격성을 시간이 적게 걸리면서도 경제적으로 평가할 수 있는 방법에 대한 연구가 필요하다. 본 연구의 목적은 열간단조 금형 육성용접부의 내균열성 및 열충격특성을 평가할 수 있는 방법에 대한 검토와 특히 내열충격성에 대해 J.W.Kim등의 시험방법을 참고하여 시간이 적게 걸리면서 저 비용으로 열 충격특성을 평가할 수 있는 시험법을 고안하는 것이다. 이를 위한 방법으로 육성용접부의 내균열성을 평가하기 위한 상온 Bending을 실시하였고, 내열충격성을 평가하기 위한 염욕로를 이용하는 고온 Bending을 고안하여 실시하였다. 상온 Bending, 고온 Bending 모두 3점 굽힘시험을 적용하였다. 고온 Bending의 가열방법으로는 염욕로를 사용하여 시편이 대기중에서 약 $850^{\circ}C$의 온도가 될 수 있도록 하였다. 시편은 각각 열처리를 하여 요구 경도를 확보하였고, 이를 염욕로에서 5분간 가열 및 유지하여 취출 후 굽힘하중을 가하여 변위의 정도로 열충격을 평가하는 방법을 사용하였다. 상온 Bending은 극한변형량과 파단부 극한응력으로, 고온 Bending은 고온 극한변형량으로 평가를 하였고, 외국산 FCW를 사용한 육성용접부를 비교대상으로 하였다. 평가 결과 개발된 국산 $3.2{\Phi}$ 태경 FCW의 성능은 외국산 FCW와 유사하거나 우수한 것으로 평가되었고, 실제 금형을 제작하여 현장에 적용한 결과 금형의 수명이 연장된 것이 나타났다.

• Aerospace Engineering and Technology
• /
• v.4 no.1
• /
• pp.143-149
• /
• 2005

To evaluate the hydraulic and cavitation performance of a fuel pump for a liquid rocket engine, performance tests of the pump, which consist of hydraulic tests and cavitation tests, were conducted in water environment with various condition. In the hydraulic tests, the head, efficiency and volute pressure distribution of the pump are found to follow the conventional similarity rule, whereas the secondary flow pressure shows a small deviation from the similarity rule. As the floating gap is constricted, the efficiency of the pump improves and the secondary flow pressure decreases. However, the inner diameter of bypass line orifice does not show clear relationship with the pump efficiency. In the cavitation tests, measurements of the head and the NPSH indicate that the pump shows better cavitation performance as the rotational speed of the pump increases.

• Korean Journal of Materials Research
• /
• v.7 no.11
• /
• pp.1007-1011
• /
• 1997

영활화혁발전소 보일러헤다 재질인 1Cr0.5Mo강의 파형에 따른 저주기 피로특성을 규명하고자 상온(298K) 및 고온(177K)의 삼각파와 사인파형 저주기 피로시험을 수행하였고 소성에너지법을 이용하여 파형에 따른 소성변형에너지와 피로수명과의 +관계를 분석하였다. 저주기 피로시 재료내부의 소성변형에너지를 히스테리시스루프의 면적으로 계산하여 구하였으며 이를통해 저주기 피로수명을 예측하였고 Coffin-Manson법 및 변형률분할법을 이용한 저주기 피로수명 결과와 서로 잘 일치하였다. 또한 상온 및 고온에서 피로반복수의 증가와 함께 재료가 반봅연화됨을 알 수 있었다.