• Clean Technology
• /
• v.16 no.3
• /
• pp.191-197
• /
• 2010

Repair reaction of plasma damaged porous methyl doped SiOCH films was carried out with silylation agents dissolved in supercritical carbon dioxide ($scCO_2$) at various reaction time, pressure, and temperature. While a decrease in the characteristic bands at $3150{\sim}3560cm^{-1}$ was detectable, the difference of methyl peaks was not identified apparently in the FT-IR spectra. The surface hydrophobicity was rapidly recovered by the silylation. In order to induce effective repair in bulk phase, the wafer was heat treated before reaction under vacuum or ambient condition. The contact angle was slightly increased after the treatment and completely recovered after the subsequent silylation. Methyl groups were decreased after the plasma damage, but their recovery was not identified apparently from the FT-IR, spectroscopic ellipsometry, and secondary ion mass spectroscopy analyses. Furthermore, Ti evaporator was performed in a vacuum chamber to evaluate the pore sealing effect. The GDS analysis revealed that the open pores in the plasma damaged films were efficiently sealed with the silylation in $scCO_2$.

• Economic and Environmental Geology
• /
• v.56 no.1
• /
• pp.13-21
• /
• 2023

X-ray powder diffraction study was conducted on the bulk modulus and phase transition behavior of synthetic zeolite X under high temperature and high pressure. Water and HCO₃^- solution were used as a PTM. Sample was heated and pressurized up to 250 ℃ and 5.18 GPa. The change of unit cell volume and phase transition were observed by X-ray diffraction. The lattice constants and unit cell volume of zeolite X, gmelinite, natrolite, and smectite were calculated using the GSAS2 program to which Le Bail's whole powder pattern decomposition (WPPD) method was applied. The bulk modulus of each zeolite X and smectite were calculated using the EosFit program to which the Birch-Murnaghan equation was applied. The bulk modulus of zeolite X is 89(3) GPa in water run, and zeolite X is 92(3) GPa in HCO₃^- solution run. In both run, pressure induced hydration (PIH) occurred due to the inflow of PTM into the zeolite X framework at initial pressure. Zeolite X transited to gmelinite, natrolite, and smectite in water run. Zeolite X, however, transited to smectite in HCO₃^- solution run. Interzeolite transformation occurred in water run, and did not occur in HCO₃^- solution run, which is assumed that conflict between the environment to form zeolite and the pH of the HCO₃^- solution.

• Clean Technology
• /
• v.29 no.1
• /
• pp.46-52
• /
• 2023

Oxalic acid has been traditionally obtained via the oxidation of carbohydrates using nitric acid and catalysts. However, this process produces a variety of nitrogen oxides during oxidation and requires a separation process due to its various intermediates. These products and additional steps increase the harmfulness and complexity of the process. Recently, the electrochemical reduction of carbon dioxide into oxalic acid has been suggested as an environmentally friendly and efficient technology for the production of oxalic acid. In this electrochemical conversion system, zinc oxalate (ZnC₂O₄) is obtained by the reaction of Zn²⁺ ions produced by Zn oxidation and oxalate ions produced by CO₂ reduction. ZnC₂O₄ can then be converted to form oxalic acid, but this requires the use of a strong acid and heat. In this study, a system was proposed that can easily convert ZnC₂O₄ to oxalic acid without the use of a strong acid while also allowing for easy separation. In addition, this proposed system can also further convert the products into glycolic acid which is a high-value-added chemical. ZnC₂O₄ was effectively separated into Zn(OH)₂ powder and oxalate solution through a chemical treatment and a vacuum filtration process. Then the Zn(OH)₂ and oxalate were electrochemically converted to zinc and glycolic acid, respectively.

• Journal of the Korean Institute of Gas
• /
• v.27 no.2
• /
• pp.39-48
• /
• 2023

This study presents the experimental results to measure the adsorption amount of methane gas by coal according to the conditions of a coalbed methane (CBM) reservoir. Adsorbed gas to coal seam particles was measured under reservoir conditions (normal pressure ~ 1,200 psi pressure range, temperature range15 ~ 45℃) using coal samples obtained from random mines in Kalimantan Island, North Indonesia. The obtained amount of absolute adsorbed gas was applied to triangular with linear interpolation to calculate the maximum amount of adsorbed gas according to temperature and pressure change, at which no experiment was performed. As a result, it was revealed that the amount of adsorbed gas to coal particles increased as the pressure increased and temperature decreased, but the increase of the amount of adsorbed gas decreased at more than an appropriate depth(1,000 ft). In the cleat permeability and cleat porosity for each depth of the coal bed considering the effective stress, the cleat permeability was 28.86 ~ 46.81 md, and the cleat porosity was 0.83 ~ 0.98%. This means that the gas productivity varies significantly with the depth because the reduction of the permeability according to the depth in the coal seam is significant. Therefore, a coalbed depth should be considered essential when designing the spacing of production wells in a coalbed methane reservoir in further study.

• Applied Chemistry for Engineering
• /
• v.34 no.6
• /
• pp.674-678
• /
• 2023

The effect of Pt was investigated to the catalytic methane decomposition of CH₄ to H₂ over Pt(1)-Fe(30)/MCM-41 and Fe(30)/MCM-41 using a fixed bed flow reactor under atmosphere. The Fe₂O₃ and Pt crystal phase behavior of fresh Pt(1)-Fe(30)/MCM-41 were obtained via XRD analysis. SEM, EDS analysis, and mapping were performed to show the uniformed distribution of nano particles such as Fe, Pt, Si, O on the catalyst surface. XPS results showed O^2-, O^- species and metal ions such as Pt⁰, Pt²⁺, Pt⁴⁺, Ft⁰, Fe²⁺, Fe³⁺ etc. When 1 wt% of Pt was added to Fe(30)/MCM-41, automic percentage of Fe2p increased from 13.39% to 16.14%, and Pt4f was 1.51%. The yield of hydrogen over Pt(1)-Fe(30)/MCM-41 was 3.2 times higher than Fe(30)/MCM-41. The spillover effect of H₂ from Pt to Fe increased the reduction of Fe particles and moderate interaction of Fe, Pt and MCM-41 increased the uniform dispersion of fine nanoparticles on the catalyst surface, and improved hydrogen yield.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.32 no.1
• /
• pp.31-38
• /
• 2024

In this study, vinyl waste, which is the cause of environmental pollution, is recycled via an electrospinning method and applied as a separator that can be employed for energy storage devices. In detail, vinyl wastes are dissolved in a solution containing p-xylene and cyclohexanone, followed by electrospinning to obtain a vinyl waste-derived separator(VWS), and then the hydrophilic functional groups on the surface of VWS are introduced using a plasma treatment to improve wettability. Scanning electron microscopy analysis have verified that the shape and thickness of as-spun VWS vary depending on the concentration of vinyl waste. The surface hydrophility of VWS is modified by plasma treatment with applied powers ranging from 80 to 120W. The lowest contact angle is observed when the 100W power is applied to VWS(VWS-100W). In electrochemical analysis, the VWS-100W-based supercapacitor device shows the highest specific capacitance of 57.9 F g^-1. This is ascribed to the high porosity achieved by electrospinning as well as the introduction of hydrophilic functional groups by the oxygen plasma treatment. In conclusion, vinyl waste is successfully recycled into separators for energy storage devices, suggesting a new way to reduce environmental pollution.

• Applied Chemistry for Engineering
• /
• v.25 no.5
• /
• pp.455-462
• /
• 2014

This work investigated the hydrophobic coating of silicate yellow phosphor powder in the form of divalent europium-activated strontium orthosilicate ($Sr_2SiO_4:Eu^{2+}$) by using an atmospheric pressure dielectric barrier discharge (DBD) plasma with argon as a carrier and hexamethyldisiloxane (HMDSO), toluene and n-hexane as precursors. After the plasma treatment of the phosphor powder, the lattice structure of orthosilicate was not altered, as confirmed by an X-ray diffractometer. The coated phosphor powder was characterized by scanning electron microscopy, fluorescence spectrophotometry and contact angle analysis (CAA). The CAA of the phosphor powder coated with the HMDSO precursor revealed that the water contact angle increased from $21.3^{\circ}$ to $139.5^{\circ}$ (max. $148.7^{\circ}$) and the glycerol contact angle from $55^{\circ}$ to $143.5^{\circ}$ (max. $145.3^{\circ}$) as a result of the hydrophobic coating, which indicated that hydrophobic layers were successfully formed on the phosphor powder surfaces. Further surface characterizations were performed by Fourier transform infrared spectroscopy and X-ray photoelectron spectrometry, which also evidenced the formation of hydrophobic coating layers. The phosphor coated with HMDSO exhibited a photoluminescence (PL) enhancement, but the use of toluene or n-hexane somewhat decreased the PL intensity. The results of this work suggest that the DBD plasma may be a viable method for the preparation of hydrophobic coating layer on phosphor powder.

• Economic and Environmental Geology
• /
• v.47 no.4
• /
• pp.421-430
• /
• 2014

In this study, a series of autoclave experiments were conducted in order to investigate the geochemical and mineralogical effects of carbon dioxide on deep subsurface environments. High pressure and temperature conditions of $50^{\circ}C$ and 100 bar, which are representative environments for geological $CO_2$ sequestration, were created in stainless-steel autoclaves for simulating the interactions in the $scCO_2$-groundwater-mineral reaction system. Zeolite, a widespread mineral in Pohang Basin where many researches have been focused as a candidate for geological $CO_2$ sequestration, and groundwater sampled from an 800 m depth aquifer were applied in the experiments. Geochemical and mineralogical alterations after 30 days of $scCO_2$-groundwater-zeolite sample reactions were quantitatively examined by XRD, XRF, and ICP-OES investigations. The results suggested that dissolution of zeolite sample was enhanced under the acidic condition induced by dissolution of $scCO_2$. As the cation concentrations released from zeolite sample increase, $H^+$ in groundwater was consumed and pH increases up to 10.35 after 10 days of reaction. While cation concentrations showed increasing trends in groundwater due to dissolution of the zeolite sample, Si concentrations decreased due to precipitation of amorphous silicate, and Ca concentrations decreased due to cation exchange and re-precipitation of calcite. Through the reaction experiments, it was observed that introduction of $CO_2$ could make alterations in dissolution characteristics of minerals, chemical compositions and properties of groundwater, and mineral compositions of aquifer materials. Results also showed that geochemical reactions such as cation exchange or dissolution/precipitation of minerals could play an important role to affect physical and chemical characteristics of geologic formations and groundwater.

• Applied Chemistry for Engineering
• /
• v.21 no.6
• /
• pp.648-652
• /
• 2010

Catalytic activities of the partial oxidation of methane (POM) to hydrogen were investigated over Pd(5)/Ti-SPK and Pd(5)/Zr-SPK in a fixed bed flow reactor (FBFR) under atmosphere, and the catalysts were characterized by BET, XPS, XRD. The BET surface areas, pore volume and pore width of Horvath-Kawaze, micro pore area and volume of t-plot of Pd(5)/Ti-SPK and Pd(5)/Zr-SPK were $284m^2/g$, $0.233cm^3/g$, 3.9 nm, $30m^2/g$, $0.015cm^3/g$ and $396m^2/g$, $0.324cm^3/g$, 3.7nm, $119m^2/g$, $0.055cm^3/g$, repectively. The nitrogen adsorption isotherms were type IV with hysteresis. XPS showed that Si 2p and O 1s core electronlevels of Ti-SPK and Zr-SPK substituted Ti and Zr shifted to slightly lower binding energies than SPK. The oxidation states of Pd on the surface of catalysts were $Pd^0$ and $Pd^{+2}$. XRD patterns showed that crystal structures of fresh catalyst changed amorphous into crystal phase after reaction. The conversion and selectivity of POM to hydrogen over Pd(5)/Ti-SPK and Pd(5)/Zr-SPK were 77, 84% and 78, 72%, respectively, at 973 K, $CH_4/O_2$ = 2, GHSV = $8.4{\times}10^4mL/g_{cat}{\cdot}h$ and were kept constant even after 3 days in stream. These results confirm superior activity, thermal stability, and physicochemical properties of catalyst in POM to hydrogen.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.40 no.1
• /
• pp.89-93
• /
• 2011

This study was conducted to investigate the proteolysis and extraction conditions of deer antler for application of food materials. ProteAX (A) was the most effective enzyme for proteolysis of deer antler and the proteolysis condition was 0.5% (w/w) for enzyme concentration and 5 hr for proteolysis time. The effect of mixing enzyme ProteAX (A)+KFEN 2 (C) treatment in $60^{\circ}C$, 5 hr was investigated; soluble solid and protein content were the highest with A 0.5% (w/w) and B 0.5% (w/w) concentration. Result for DAH (deer antler hydrolysate) and DA (deer antler) prepared with extraction in $95^{\circ}C$ atmospheric pressure (AP, 6~18 hr) and extraction under $120^{\circ}C$ pressure condition (UP, 15~60 min) after hydrolysis on preceding established condition descriptions indicated that difference in pH according to enzyme treatment and extraction conditions was not significant. Sugar content of DA was $1.5^{\circ}Brix$, DA-UP (under pressure) and DAH-AP (atmospheric pressure) were $2.2^{\circ}Brix$; the highest sugar content of $2.7^{\circ}Brix$ was observed in DAH-UP for 60 min extraction. Also total free sugar, crude protein and collagen content were the highest in DAH-UP for 60 min recording at 1.97%, 742.7 mg/100 g and 498.8 mg/100 g, respectively. From these results, deer antler hydrolysate prepared with extraction under pressure was the most effective for functional characteristics enhancement. Hereafter, various practical uses of materials with enhanced characteristics of antler is expected.