• Journal of the Korean Geotechnical Society
• /
• v.33 no.12
• /
• pp.75-80
• /
• 2017

Permeable block pavement systems are widely used to relieve the flood and enhance water circulation. However, domestic design method has not yet been established well. Although AASHTO 93 flexible pavement design method is applied as a structural design method outside the country, there is a lack of information on layer coefficient of the permeable pavement materials, which makes it difficult to apply the design to various materials. Therefore, in this study, a method of calculating the layer coefficient of permeable block pavement materials by plate load test was presented and the layer coefficient of a permeable block pavement in a testbed was evaluated. Overall, calculated layer coefficient of open graded aggregate and permeable block pavement surface layer were similar to those of the conventional values. The presented method may be used to evaluate layer coefficients of permeable block pavements for design.

• 한국도로학회지:도로
• /
• v.5 no.4 s.18
• /
• pp.36-46
• /
• 2003

포장구조체에서 요구되는 강도를 갖게 하는 구조 설계의 방법은 경험적 절차부터 반역학적 절차까지 발전되어 왔다. 재생 가열아스팔트혼합물이 기존의 가열아스팔트혼합물(HMA)과 비교하여 비슷하거나 때에 따라 더 좋은 성능을 가져오므로, AASHTO설계지침서에서는 본질적으로 재생(recycled) HMA 재료와 신생(virgin) HMA 재료간의 차이가 없다고 기술하고 있으며, 기존 HMA 재료에 사용되는 덧씌우기설계법의 구조회복 분석방법(structural rehabilitation analysis method)을 재생포장설계에도 권장하고 있다. 재생 가열아스팔트의 설계를 위한 AASHTO 방법은 설계교통량, 교통량 및 수행능력예측의 신뢰수준, 공용기간, 그리고 포장상태 평가지수에 의하여 결정된 포장구조체에서 요구되는 포장두께지수(SN)에 기초한다. 포장두께지수(SN)는 포장층 두께, 상대강도계수, 각 층의 배수조건들의 곱의 조합으로서 나타내어질 수 있다. 덧씌우기로 간주될 수 있는 재생된 층의 포장두께지수(SN)는 기존 포장에서의 포장두께지수와 보강된 포장에서 요구되는 포장두께지수의 차이에 의하여 계산되어질 수 있다. 상대강도계수의 값은 AASHTO 설계지침에 명시되어 있다. AI 방법은 교통량, 노상의 회복탄성계수, 그리고 설계두께를 계산하기 위한 표층과 기층의 종류를 사용한다. 이 방법은 재생된 가열혼합물질과 기존의 가열혼합물질과는 거의 비슷한 성능을 나타낸다고 본다. 또다른 AI 방법에 의하면 재생된 층은 덧씌우기층이라고 간주하고, 현재의 포장두께와 요구되어지는 포장두께 사이의 차를 이용하여 재생될 층의 두께를 산정한다. 소요되는 덧씌우기 두께는 포장의 현장 상태지수(condition rating)와 각 종류에 따른 포장체와 포장재료가 아스팔트 콘크리트층의 등가두께로 전환되어 나타나는 방법에 근거하여 결정될 수 있다. 또 다른 방법은 포장체 각 층의 물성과 하중을 이용한 컴퓨터 프로그램에 의하여 산정된 하중-변형 응답에 의한 설계 방법을 포함한다. 이런 방법들에서는 포장체는 탄성이나 점탄성층 위에서 탄성이나 점탄성 거동을 보인다고 가정한다. 재생 상온혼합물에서의 AASHTO 설계 방법은 가열혼합물의 설계방법과 유사하다. 그러나, 재생 상온혼합물에서의 상대강도계수는 시공방법에 좌우되므로, 기술자의 판단을 근거로 하여 결정되어져야 한다. AI방법에서는 포장구조체를 다층탄성구조라고 보고, 노상의 강도와 설계 교통량을 근거로 요구되는 포장두께를 결정한다. 재생 상온혼합물 기층의 두께는 재생 상온혼합물 기충 위에서 가열아스팔혼합물에 대하여 산정된 덧씌우기 두께를 이용하여 결정할 수 있다. 아스팔트 표면의 재생은 기존 포장의 구조적 능력을 정상적으로 개선할 수 없으므로, 표면 재생의 두께를 설계하는 방법은 없다. 그러나, 임의의 덧씌우기 두께는 기존의 덧씌우기 설계법에 기초하여 산정 할 수 있다. 만약 덧씌우기가 승차감만을 개선시킨다고 여겨진다면, 혼합물에서 사용되어지는 최대 골재 크기에 기초한 최소 두께를 결정할 수 있다.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.12
• /
• pp.53-63
• /
• 2008

In this study, the cone tip resistances of cemented sand are measured by performing a series of miniature cone penetration tests in large calibration chamber, and the relations with constrained modulus, unconfined compressive strength, and shear strength of cemented sand are suggested. Experimental results show that both the cone tip resistance and constrained modulus of sand increase with increasing cementation effect as well as relative density and confining stress. However, it is observed that the relative density and confining stress have more significant influence on cone tip resistance than constrained modulus of cemented sand. Since the cone penetration into the ground induces the damage of cementation, the cone tip resistance can't properly reflect the cementation effect of sand. An analysis based on the constrained modulus shows that the measured cone tip resistance underestimates the deformation modulus of cemented sand by about $70{\sim}85%$. In addition, this study establishes various relationships among the above soil properties from the regression analysis.

• 한국도로학회:학술대회논문집
• /
• 2004.10a
• /
• pp.39-45
• /
• 2004

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.4
• /
• pp.54-61
• /
• 2023

In this paper, the compressive strength, pore characteristics, and chloride diffusion coefficient were measured at 28 days of age in order to examine the influence of curing conditions for the chloride diffusion and pores in concrete cured under extreme condition. According to the test results, the compressive strength was improved as the relative humidity increased. Additionally, higher compressive strength was observed when the specimens were cured at 35℃. However, the compressive strength of specimens cured at 45℃ was decreased. Meanwhile, the chloride diffusion coefficient decreased with an increase in curing temperature and relative humidity, indicating a difference compared to the trend observed for compressive strength. On the other hand, the excellent correlation showed between compressive strength and chloride diffusion coefficient, porosity and chloride diffusion coefficient when the concrete cured under water. However, when the concrete cured under extreme condition, this correlation was significantly reduced compared to the water curing case. In contrast, it has been determined that there is no significant correlation between the average pore size and chloride diffusion coefficient, regardless of the curing conditions.

• Journal of the Korea Convergence Society
• /
• v.10 no.4
• /
• pp.139-145
• /
• 2019

This paper investigated the strength and stiffness of composite truss unit structures. The model used is a core-filled model combining the Kagome model and the cube truss model. The material properties used for the analysis are 304 stainless steel with elastic modulus of 193 GPa and yield stress of 215 MPa. The theoretical equation is derived from the relative elasticity relation of Gibson - Ashby ratio, the analysis was performed using Deform 3D, a commercial tool. In conclusion, the relative elasticity for this unit model correlates with 1.25 times the relative density and constant coefficient, elasticity is inversely proportional to pore size. The relative compressive strength has a correlation with relative density of 1.25 times. Proof of this is a real experiment, the derived theoretical relationship should further consider mechanical behavior such as bending and buckling. In the future, it is hoped that the research on the elasticity and the stress according to the structure of the three-dimensional space will be continued.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.10 no.2
• /
• pp.159-167
• /
• 2022

The present study assessed the micro structure and durability characteristics of ternary blended cement with different types of alkali activators. Ground granulated blast furnace slag(GGBS) and ferronickel slag(FNS) was replaced until 50 % of the weight of cement. In addition, potassuim hydroxide and sodium hydroxide were used for comparing the properties of different type of alkali activator. Ternary blended cement with alkali activators showed higher peak portlandite peak than that of OPC(Ordinary Portlande Cement) and non activated ternary blended cement. Also, there was no new hydration products in ternary blended cement or/and alkali activators. Based on the mercury intrustion porosimetry(MIP) test result, ternary blended cement increased macro pore while alkali activated ternary blended cement modified pore structure and increased microp pore as compared to OPC as control. Combination with alkali activators is desirable to enhance the compressive strength and freeze thaw resistance.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.5
• /
• pp.42-48
• /
• 2017

When concrete structures expose to fire, the structures were damaged accompanied with degradation of material properties of concrete. In order to determine the reuse of fire-damaged concrete structures, it is needed a careful determination considering conditions of fire damage, such as exposure temperature and exposure time, and also potential to restore fire damage. This study investigates on the evaluation of residual material properties of fire-damaged concrete under different post-fire curing regimes. An experimental study was performed on concrete samples to measure the dynamic elastic modulus by the impact resonance vibration method. Upon the experimental results, the evidence of restoration of material properties was confirmed on specific post-fire curing regimes, higher humidity conditions. Additionally, a correlation analysis was performed on the dynamic elastic modulus with the tensile strength for identifying the effects of post-fire curing regimes on both material properties of fire-damaged concrete.

• Journal of the Korea Concrete Institute
• /
• v.23 no.1
• /
• pp.23-30
• /
• 2011

In this study, deterioration degrees of concrete were investigated at laboratory under seawater attack and cycling freeze-thaw, which are major durability performance deterioration factors of concrete. Deteriorations of mixed concrete using Portland & blended cement were examined by instrumental analysis of changes in relative dynamic modulus of elasticity and compressive strength. After 520 cycles of freeze-thaw, relative dynamic modulus of elasticity and compressive strength of concrete mixed with normal Portland and LHC over 75% showed relatively low resistance of approximately 44% of those values of SRC. Concrete replaced with 50% fine powder of blast furnace slag showed the most excellent freeze-thaw resistance among the tested blended cement concrete.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2002.12a
• /
• pp.130-131
• /
• 2002

Terfenol-D는 상온에서 변형이 가장 큰 재료로 알려져 있고, 자기역학적 결합계수 k$_{33}$=0.75로 매우 높기 때문에 전기에너지를 역학적 에너지로 효율적으로 변환시킬 수 있다[1]. 단점으로는 압축강도는 700 ㎫로 높으나, 인장강도 30 ㎫로 매우 낮아서 재료가 brittle하여 장치 설계 시 세심한 주의가 필요하며, 재료의 상대투자율이 3~10정도로 낮기 때문에 자기폐회로를 구성하는데 어려움이 있다[2-4]. (중략)략)