• Journal of the Korean Wood Science and Technology
• /
• 제36권1호
• /
• pp.61-68
• /
• 2008

The effect of rupture on the speed of ultrasonic wave was investigated with the PUNDIT and the effective detecting method of defects, moving transmitter and receiver. The speed of ultrasonic wave according to the course of rupture was not affected by transmitter and receiver and in the course of parallel rupture, but only in the course of vertical rupture. When rupture was not located on the ultrasonic wave progressing course, rupture was not detected. However, if rupture was formed perpendicularly to the ultrasonic wave progressing course but located on the ultrasonic wave progressing direction, rupture can be detected. Also, the rupture can be detected, when one transmitter and receiver was placed at top and the other at bottom. After detecting rupture in a part, rupture was determined accurately, placing and moving two transmitters and receivers at width.

• Journal of the Korean Geosynthetics Society
• /
• 제11권4호
• /
• pp.1-8
• /
• 2012

In this study, the earth pressure, displacement and strain were compared with reinforcement types at segmental retaining wall through full scale model test. The test results found that the measurement of earth pressure and displacement at wall for the fully reinforced retaining wall are different from those for the partly reinforced retaining wall. The analyses of these results would suggest that the used of geoogrid allowed the vertical earth pressure and displacement at wall to be reduced. The horizontal earth pressure in upper and lower part of wall can change with reinforcement type and earth deformation and were larger than the active and the rest pressure. Also, the lateral earth pressure and displacement of wall have a very high a correlation. It was found that the strain contour distribution of reinforcements was occurred a large strain at cental part of wall in segmental retaining wall system.

• Proceedings of the Korea Contents Association Conference
• /
• 한국콘텐츠학회 2006년도 추계 종합학술대회 논문집
• /
• pp.856-859
• /
• 2006

Patient's position who muscle ache curer for hospital undergoes person entrance and treatment that take advantage of biological, physical force of low frequency and it is equipment that treat body muscle ache, but use equipment when use patient into compensation in hospital specially, that consider everybody is important first of all. This research question investigation with market survey of old product enforce because preference degree reflected officer a result and apply opinion tuned with product development connection engineers on DESIGN direction via typical product design development process close. This curer development research analyzed data involved directly taking advantage of FGI techniques with literature investigation collection. Investigation examined laying stress on muscle ache curer for hospital and a nurse than a doctor answered on question and purchase selection criterion or price portion to user focus. Direct market survey research that see item indicated by competition four provision shortcomings consequently in NEW MODEL development hereafter supplement and expectation. by contributing greatly in M/S security strategy hereafter because design development consisted for side that improve.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• 제21권12호
• /
• pp.3265-3276
• /
• 1996

The studies of document recongnition have been focused mainly on Korean documents. But most of documents composed of Korean and other characters. So, in this paper, we propose the document recognition system that can recognize the multi-size, multi font and mixed type characters. We have utilized a large scale network model, "CombNET" which consists of a 4 layered network with combstructure. And we propose recognition method that can recognize characters without discrimination of character type. The first layer constitutes a Kohonen's SOFM network which quantizes an input feature vector space into several sub-spaces and the following 2-4 layers constitutes BP network modules which classify input data in each sub-space into specified catagories. An experimental result demonstrated the usefulness of this approach with the recognition rates of 95.6% for the training data. For the mixed type character documents we obtained the recognition rates of 92.6% and recognition speed of 10.3 characters per second.

• Fire Science and Engineering
• /
• 제24권6호
• /
• pp.153-159
• /
• 2010

In this study, we confirmed the fact that air egress velocity of pressure differential system installed at vestibule of smokeproof stairway in domestic high-rise building becomes back-flow to stair-lobby at upper vestibule. Rather it do not back-flow to the livingroom. when fire occur and the door opens to escape from fire zone. so we carry out actual and computational fluid dynamics measurement. In the case upward 45 gradient of supply damper's blade, The simulation results that air flow of upper vestible is steady but back-flow phenomenon occurred at the bottom. However, in the case of $4m^2$, direction of the flow was ideal to living room. If a vestibule’s area is smaller, it must be designed and built according to performance-based design.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• 제37권9호
• /
• pp.837-845
• /
• 2013

An airlift pump can be used to pump liquids and sediments within itself, which cannot easily be pumped up by a conventional method, by using the airlift effect. This characteristic of the airlift pump can be exploited in a DCFC (Direct Carbon Fuel Cell) so that molten fuel with high temperature may be carried or transported. The basic characteristics of airlift are investigated. A simple system is constructed, where the reservoir is filled with water, a tube is inserted, and air is supplied from the bottom of the tube. Then, water is lifted and its flow rate is measured. Bubble patterns in the tube are observed in a range of air flow rates with the parameters of the tube diameter and submergence ratio, leading to four distinct regimes. The pumping performance is predicted, and the correlation between the supplied gas flow rate and the induced flow rate of water is found.

• Journal of the Korea Institute of Building Construction
• /
• 제16권5호
• /
• pp.397-403
• /
• 2016

As a building energy saving standard strengthened, The number of building installed external thermal insulation composite system(ETICS) using EPS insulation increased. But frequent fire accident in the buildings installed EIFS using EPS led to strengthening of building fire safety regulation. This study is for fire property of EPS ETICS reinforced with noncombustible calcium silicate-based mineral insulation as a fire spread prevention structure(FSPS). Fire test for large scale wall by ISO 13785-2 was applied and results showed EPS EIFS with FSPS got 3~8 times superior fire safety than normal EIFS by visual investigation. Temperature and heat flux measurement results, which data of upside of specimen were lower than downside, also supported fire safety of EIFS with FSPS.

• Proceedings of the Korea Concrete Institute Conference
• /
• 한국콘크리트학회 2008년도 춘계 학술발표회 제20권1호
• /
• pp.601-604
• /
• 2008

When the concrete is placed, the water, needed for hydration of the cement, is under 30% of W/C including bound and gel water. However, as minimum water content cause bad workability, the W/C have to be higher. Therefore, fresh concrete produce 10${\sim}$20% extra water. As those water remain entrapped air in the concrete, life of the structure is reduced because of the degradation caused by entrapped air. For that reason, if extra water is eliminated, it will be great to improve the durability of the structures. Therefore, this study was performed to verity the fundamental properties through the experiment on the dewatering system using the euro form for eliminating extra water. When the dewatering form was applicated, the compressive strength was increased by 16% than those of normal form. However, the increasing rate of compressive strength got lower as the height is higher. In terms of ultrasonic pulse speed and surface roughness, the dewatering form showed better results than the normal one.

• Proceedings of the Korea Water Resources Association Conference
• /
• 한국수자원학회 2016년도 학술발표회
• /
• pp.17-17
• /
• 2016

이중편파 레이더는 수평 수직반사도($Z_H{\cdot}Z_V$), 차등반사도($Z_{DR}$), 교차상관계수(${\rho}_{HV}$), 차등위상차(${\Phi}_{DP}$) 등 다양한 변수 산출을 통하여 대기 수상체 구분, 우적분포에 영향이 적은 강우량 추정, 밝은 띠(BB, Bright Band)의 탐지 등이 가능하게 됨으로써 수문기상 및 재해관리 분야에 활용성이 점점 더 커지고 있다. 본 연구는 RHI, PPI에서 생산된 레이더 변수를 이용하여 BB를 탐지하고 그 특성을 평가하였다. BB는 레이더를 이용하여 상층대기를 관측할 때 수직단면에서 강수입자가 눈에서 비로 변하는 구간에서 과대하게 높은 반사도가 나타나는 층을 말한다. BB에서는 QPE가 과대 추정되기 때문에, BB의 특성 파악은 레이더의 관측전략 수립과 QPE 보정에 필수적이다. 본 연구에서는 RHI에 의한 $Z_H$의 연직단면분석, RHI와 PPI의 고도각 경사거리(slant range) 빔의 ${\rho}_{HV}$, $Z_{DR}$, $Z_H$에 의한 분석을 통하여 BB의 상단부($BB_{TOP}$), 최정점($BB_{PEAK}$) 및 하단부($BB_{BOTTOM}$)의 고도를 상호 비교 평가하였다. 분석 자료는 KICT X-밴드 레이더에 의한 관측한 2015년 10월 21일의 층상운에 의한 강우를 이용하였다. RHI에 의한 $Z_H$의 연직단면 분석결과 $BB_{top}$, $BB_{bottom}$ 및 $BB_{peak}$는 KICT 레이더 고도(MSL : 40m)를 기준으로 각각 3.26Km, 2.3Km($BB_{width}$: 0.96km) 및 2.7Km로 나타났다. 이 같은 결과는 다른 2가지 분석방법에서도 유사하게 나타나고 있으며, 이는 BB분석을 위해 다양한 변수를 통한 신뢰성 있는 BB의 특성을 파악할 수 있는 기반을 제공한다.

• Asia-pacific Journal of Multimedia Services Convergent with Art, Humanities, and Sociology
• /
• 제8권3호
• /
• pp.589-596
• /
• 2018

Transportation or structure has the important role at clothing, food, and housing at modern society. If even the small crack happens and propagates at transportation or structure, the parts are fractured and they can cause a disaster. CT specimen was used in order to investigate the damage trend due to the crack propagation at this study to prevent this situation. As the material of CT specimen, the unidirectional carbon fiber reinforced plastic of the composite material in the limelight nowadays. The laminate angle designated in order of [60/-60/60/-60] was applied to the specimen model with the unidirectional fiber. As the analysis condition, the forced displacement was applied to the hole of upper part after fixing the hole of lower part. At the result of this study, the equivalent stress and shear stress was shown to be higher in order of the structural steel, copper, titanium and aluminum. This study result is thought to be utilized usefully at verifying the damage of CT specimen made of inhomogeneous material.