• Journal of Bio-Environment Control
• /
• v.28 no.1
• /
• pp.78-85
• /
• 2019

This study was designed to examine the performance of an aspirated radiation shield(ARS), which was made at the investigator's lab and characterized by relatively easier making and lower costs based on survey data and reports on errors in its measurements of temperature and relative humidity. The findings were summarized as follows: the ARS and the Jinju weather station made measurements and recorded the range of maximum, average, and minimum temperature at $2.0{\sim}34.1^{\circ}C$, $-6.1{\sim}22.2^{\circ}C$, $-14.0{\sim}15.1^{\circ}C$ and $0.4{\sim}31.5^{\circ}C$, $-5.8{\sim}22.0^{\circ}C$, $-14.1{\sim}16.3^{\circ}C$, respectively. There were no big differences in temperature measurements between the two institutions except that the lowest and highest point of maximum temperature was higher on the campus by $1.6^{\circ}C$ and $2.6^{\circ}C$, respectively. The measurements of ARS were tested against those of a standard thermometer. The results show that the temperature measured by ARS was lower by $-2.0^{\circ}C$ or higher by $1.8^{\circ}C$ than the temperature measured by a standard thermometer. The analysis results of its correlations with a standard thermometer reveal that the coefficient of determination was 0.99. Temperature was compared between fans and no fans, and the results show that maximum, average, and minimum temperature was higher overall with no fans by $0.5{\sim}7.6^{\circ}C$, $0.3{\sim}4.6^{\circ}C$ and $0.5{\sim}3.9^{\circ}C$, respectively. The daily average relative humidity measurements were compared between ARS and the weather station of Jinju, and the results show that the measurements of ARS were a little bit higher than those of the Jinju weather station. The measurements on June 27, July 26 and 29, and August 20 were relatively higher by 5.7%, 5.2%, 9.1%, and 5.8%, respectively, but differences in the monthly average between the two institutions were trivial at 2.0~3.0%. Relative humidity was in the range of -3.98~+7.78% overall based on measurements with ARS and Assman's psychometer. The study analyzed correlations in relative humidity between the measurements of the Jinju weather station and those of Assman's psychometer and found high correlations between them with the coefficient of determination at 0.94 and 0.97, respectively.

• Journal of the Korean Society of Food Culture
• /
• v.22 no.6
• /
• pp.721-741
• /
• 2007

1. For the types of boiled rice, there were 1 type of bap, 1 type of jebap cooked with glutinous rice, 13 types of boiled rice cooked by mixing grains and nuts such as daemakban, somakban, jobap, cheongryangmiban, jobap, gijangbap, yulmubap, hyeonmibap, boribap and patmulbap as well as patbap, congbap, byeolbap and bambap etc as ogokbap. Also, there were 12 types of bap cooked by mixing herb medicinal ingredients such as cheongjeong, oban, boksungabap, gumeunsaekbap, hwanggukgamchobap, yeongeunbap, okjeongbap, gogumabap, dububap, samssibap, dorajibap, gamjabap, songibap and jukshilbap. There were 7 types bap cooked as unique one bowl dish at the present as bapby mixing fish, meat, shellfish and milk as ingredients are hwangtang, gyejanggukbap, janggukbap, gulbap, kimchibap, chusaban and bibimbap, etc and the types of bap that have been analyzed are 34 total. 2. For the food ingredients used in bap types 23 types of miscellaneous grains, 5 types of nuts and 11 types of meat, 6 types of fish, 35 types of vegetables, 2 types of fruit including pears or peaches were used. Garlic wasn't used perhaps because of it being boiled rice 3. Types of Sap by Cooking Methods. (1) The ssalbap was cooked by first boiling water, putting in rice grains and boiling hard to be cooked as overcooked bap (rice). (2) The japgokbap (boiled cereals) has used buckwheat, barley job's tear, etc to be boiled down by soaking the ones with large grains (beans) first in advance to be boiled down or cooked by crushing into fine pieces. The red bean, etc was boiled down in advance or placed at the bottom of pot by cutting into two pieces while jujube or nut was cut into three pieces to cook the bap by pouring a lot of water and mixing other ingredients. (3) The gukbap (soup boiled rice), etc were cooked by squeezing out the yellow chrysanthemum that has dried chrysanthemum to cook the boiled rice by putting in rice and gukbap, meat or bones, etc were boiled down for a long time and decorated with meat or wild greens by mixing the bap in the meat juice. For gulbap (oyster boiled rice), etc, it was cooked as ingredients were stir fried in advance or washed and put in when the bap was about half cooked. (4) For bibimbap (mixed boiled rice), after the bap was overcooked first with rice, the wild greens were mixed lightly with bap beforehand, then the wild greens, decorations and garnishings were laid above rice and red pepper powder was sprinkled. (5) Namchok leaves, etc were boiled to cook the boiled rice with rice after being cooled while namchok stem and leaves were pounded to make juice and cooked the bap with rice. The peach, lotus root and yams were cut into fine pieces to be put in together when rice was about half done. The bellflower was soaked in water to be boiled down for a long time while potatoes and pine mushrooms, etc were cut into fine pieces to cook the bap (boiled rice) with rice.

• Journal of Venture Innovation
• /
• v.5 no.3
• /
• pp.57-70
• /
• 2022

In modern industrial capitalism, the relationship between the provision of work and the receipt of wages has become an important principle governing society. According to the labor contract, the wages provided by entrusting the right to dispose of one's labor to the employer are directly compensated, and human life should be guaranteed and reproduced with proper rest. The establishment of labor relations under free contracts represents a problem in protecting workers, and accordingly, the maximum of working hours is set as a minimum right for workers, and the standard for minimum rest is set and assigned. The reduction of working hours is very important in terms of the quality of life of workers, but it is also an important issue in efficient corporate activities. As of 2020, Korea has 1,908 hours of annual working hours, the third lowest among OECD 37 countries in the happiness index surveyed by the Sustainable Development Solution Network(SDSN), an agency under the United Nations. Accordingly, the necessity of reducing working hours has been recognized, and the maximum working hours per week has been limited to 52 hours since 2018. In this situation, various working hours are legally excluded as a way to maintain the company's value-added creation and meet the diverse needs of workers, and Korea's Labor Standards Act restricts flexible working hours within three months, flexible working hours exceeding three months, selective working hours, and extended working hours. However, in the discussion on the application of the revised flexible working hours system in 2021 and the expansion of the settlement unit period recently discussed, there is a problem with the flexible working hours system, which needs to be improved. Therefore, this paper aims to examine the problems of the flexible working hours system and improvement measures. The flexible working hours system is a system that does not violate working hours even if the legal working hours are exceeded on a specific day or week according to a predetermined standard, and does not have to pay additional wages for excessive overtime work. It is mainly useful as a form of shift work in manufacturing, sales service, continuous business or electricity, gas, water, and transportation for long-term operations. It is also used as a way to shorten working hours, such as expanding holidays through short working days. However, if the settlement unit period is expanded, it is disadvantageous to workers as the additional wages that workers can receive will not be received. Therefore, First, in order to expand the settlement unit period currently under discussion, additional wages should be paid for the period expanded from the current standard. Second, it is necessary to improve the application of the flexible working hours system to individual workers to have sufficient consultation with individual workers in a written agreement with the worker representative, Third, clarify the allowable time for extended work during the settlement unit period, and Fourth, limit the daily working hours or apply to continuous rest. In addition, since the written agreement of the worker representative is an important issue in the application of the flexible working hours system, it is necessary to secure the representation of the worker representative.

• Journal of Agricultural Extension & Community Development
• /
• v.7 no.1
• /
• pp.155-166
• /
• 2000

When the marcher visited Korea in fall 1994, he was shocked to see high rise apartment buildings around the capitol region including Seoul and Suwon, resulting from rising demand of housing because of urban migration followed by second and third industrial development. After 6 years in March 2000, the researcher witnessed more apartment buildings and vinyl house complexes, one of the evidences of continued economic progress in Korea. Korea had to receive the rescue finance from International Monetary Fund (IMF) because of financial crisis in 1997. However, the sign of recovery was seen in a year, and the growth rate of Gross Domestic Products (GDP) in 1999 recorded as high as 10.7 percent. During this period, the Korean government has been working on restructuring of banks, enterprises, labour and public sectors. The major directions of government were; localization, reducing administrative manpower, limiting agricultural budgets, privatization of public enterprises, integration of agricultural organization, and easing of various regulations. Thus, the power of central government shifted to local government resulting in a power increase for city mayors and county chiefs. Agricultural extension services was one of targets of government restructuring, transferred to local governments from central government. At the same time, the number of extension offices was reduced by 64 percent, extension personnel reduced by 24 percent, and extension budgets reduced. During the process of restructuring, the basic direction of extension services was set by central Rural Development Administration Personnel management, technology development and supports were transferred to provincial Rural Development Administrations, and operational responsibilities transferred to city/county governments. Agricultural extension services at the local levels changed the name to Agricultural Technology Extension Center, established under jurisdiction of city mayor or county chief. The function of technology development works were added, at the same time reducing the number of educators for agriculture and rural life. As a result of observations of rural areas and agricultural extension services at various levels, functional responsibilities of extension were not well recognized throughout the central, provincial, and local levels. Central agricultural extension services should be more concerned about effective rural development by monitoring provincial and local level extension activities more throughly. At county level extension services, it may be desirable to add a research function to reflect local agricultural technological needs. Sometimes, adding administrative tasks for extension educators may be helpful far farmers. However, tasks such as inspection and investigation should be avoided, since it may hinder the effectiveness of extension educational activities. It appeared that major contents of the agricultural extension service in Korea were focused on saving agricultural materials, developing new agricultural technology, enhancing agricultural export, increasing production and establishing market oriented farming. However these kinds of efforts may lead to non-sustainable agriculture. It would be better to put more emphasis on sustainable agriculture in the future. Agricultural extension methods in Korea may be better classified into two approaches or functions; consultation function for advanced farmers and technology transfer or educational function for small farmers. Advanced farmers were more interested in technology and management information, while small farmers were more concerned about information for farm management directions and timely diffusion of agricultural technology information. Agricultural extension service should put more emphasis on small farmer groups and active participation of farmers in these groups. Providing information and moderate advice in selecting alternatives should be the major activities for consultation for advanced farmers, while problem solving processes may be the major educational function for small farmers. Systems such as internet and e-mail should be utilized for functions of information exchange. These activities may not be an easy task for decreased numbers of extension educators along with increased administrative tasks. It may be difficult to practice a one-to-one approach However group guidance may improve the task to a certain degree.

• Journal of Korean Society of Forest Science
• /
• v.52 no.1
• /
• pp.37-49
• /
• 1981

The purpose of the study is to find out the objective method of valuation on the forest stands through the analysis of logging costs that is positively related to timber production. The two forest (Amgog, Whangryoung), located nereby, but forest type, logging and skidding conditions being slightly different, were slected to carry out the study. The objective timber stumpage value were determined by investigating the appropriate timber production costs and profits of logging operations. The main result obtained in this study are as follows: 1. The rate of logging cost in consisting of timber market price is 13.15% in the area of Amgog logging place and 19.48% in Whangryoung. 2. The rate of the other production cost excluding logging cost is 15.36% in the area of Amgog logging place and 28.85% in Whangryoung. 3. The total rate of timber production cost in consisting of the market price is more than 28.51% in the area of Amgog logging place and 48.33% in Whangryoung, 4. Though the productivity of forest land is affected by the selection of tree species, tending, treatments and effective management of forest land, the more important problem is improvement of logging condition. 5. The rate of production cost in timber price is so high that we should endeavore to improve the productivity of labour and its quality, and minimize the difference of piece work per day in accordance to the various site condition. 6. Although the profit of forest industry is related to the period of recapturing investment, it is more closely related to the working condition, risk of investment and continuous change of social investment interest. 7. If the right variables which are related to the timber market, are objectively obtained, the stumpage value of mature forests can be objectively caculated by applying straight line discounting method or compound discounting method in caculating the stump to market price.

• Journal of Bio-Environment Control
• /
• v.5 no.2
• /
• pp.215-235
• /
• 1996

The thermal analysis by mathematical model simulation makes it possible to reasonably predict heating and/or cooling requirements of certain greenhouses located under various geographical and climatic environment. It is another advantages of model simulation technique to be able to make it possible to select appropriate heating system, to set up energy utilization strategy, to schedule seasonal crop pattern, as well as to determine new greenhouse ranges. In this study, the control pattern for greenhouse microclimate is categorized as cooling and heating. Dynamic model was adopted to simulate heating requirements and/or energy conservation effectiveness such as energy saving by night-time thermal curtain, estimation of Heating Degree-Hours(HDH), long time prediction of greenhouse thermal behavior, etc. On the other hand, the cooling effects of ventilation, shading, and pad ||||&|||| fan system were partly analyzed by static model. By the experimental work with small size model greenhouse of 1.2m$\times$2.4m, it was found that cooling the greenhouse by spraying cold water directly on greenhouse cover surface or by recirculating cold water through heat exchangers would be effective in greenhouse summer cooling. The mathematical model developed for greenhouse model simulation is highly applicable because it can reflects various climatic factors like temperature, humidity, beam and diffuse solar radiation, wind velocity, etc. This model was closely verified by various weather data obtained through long period greenhouse experiment. Most of the materials relating with greenhouse heating or cooling components were obtained from model greenhouse simulated mathematically by using typical year(1987) data of Jinju Gyeongnam. But some of the materials relating with greenhouse cooling was obtained by performing model experiments which include analyzing cooling effect of water sprayed directly on greenhouse roof surface. The results are summarized as follows : 1. The heating requirements of model greenhouse were highly related with the minimum temperature set for given greenhouse. The setting temperature at night-time is much more influential on heating energy requirement than that at day-time. Therefore It is highly recommended that night- time setting temperature should be carefully determined and controlled. 2. The HDH data obtained by conventional method were estimated on the basis of considerably long term average weather temperature together with the standard base temperature(usually 18.3$^{\circ}C$). This kind of data can merely be used as a relative comparison criteria about heating load, but is not applicable in the calculation of greenhouse heating requirements because of the limited consideration of climatic factors and inappropriate base temperature. By comparing the HDM data with the results of simulation, it is found that the heating system design by HDH data will probably overshoot the actual heating requirement. 3. The energy saving effect of night-time thermal curtain as well as estimated heating requirement is found to be sensitively related with weather condition: Thermal curtain adopted for simulation showed high effectiveness in energy saving which amounts to more than 50% of annual heating requirement. 4. The ventilation performances doting warm seasons are mainly influenced by air exchange rate even though there are some variations depending on greenhouse structural difference, weather and cropping conditions. For air exchanges above 1 volume per minute, the reduction rate of temperature rise on both types of considered greenhouse becomes modest with the additional increase of ventilation capacity. Therefore the desirable ventilation capacity is assumed to be 1 air change per minute, which is the recommended ventilation rate in common greenhouse. 5. In glass covered greenhouse with full production, under clear weather of 50% RH, and continuous 1 air change per minute, the temperature drop in 50% shaded greenhouse and pad ＆ fan systemed greenhouse is 2.6$^{\circ}C$ and.6.1$^{\circ}C$ respectively. The temperature in control greenhouse under continuous air change at this time was 36.6$^{\circ}C$ which was 5.3$^{\circ}C$ above ambient temperature. As a result the greenhouse temperature can be maintained 3$^{\circ}C$ below ambient temperature. But when RH is 80%, it was impossible to drop greenhouse temperature below ambient temperature because possible temperature reduction by pad ||||&|||| fan system at this time is not more than 2.4$^{\circ}C$. 6. During 3 months of hot summer season if the greenhouse is assumed to be cooled only when greenhouse temperature rise above 27$^{\circ}C$, the relationship between RH of ambient air and greenhouse temperature drop($\Delta$T) was formulated as follows : $\Delta$T= -0.077RH＋7.7 7. Time dependent cooling effects performed by operation of each or combination of ventilation, 50% shading, pad ＆ fan of 80% efficiency, were continuously predicted for one typical summer day long. When the greenhouse was cooled only by 1 air change per minute, greenhouse air temperature was 5$^{\circ}C$ above outdoor temperature. Either method alone can not drop greenhouse air temperature below outdoor temperature even under the fully cropped situations. But when both systems were operated together, greenhouse air temperature can be controlled to about 2.0-2.3$^{\circ}C$ below ambient temperature. 8. When the cool water of 6.5-8.5$^{\circ}C$ was sprayed on greenhouse roof surface with the water flow rate of 1.3 liter/min per unit greenhouse floor area, greenhouse air temperature could be dropped down to 16.5-18.$0^{\circ}C$, whlch is about 1$0^{\circ}C$ below the ambient temperature of 26.5-28.$0^{\circ}C$ at that time. The most important thing in cooling greenhouse air effectively with water spray may be obtaining plenty of cool water source like ground water itself or cold water produced by heat-pump. Future work is focused on not only analyzing the feasibility of heat pump operation but also finding the relationships between greenhouse air temperature(T$_{g}$ ), spraying water temperature(T$_{w}$ ), water flow rate(Q), and ambient temperature(T$_{o}$).

• Journal of Intelligence and Information Systems
• /
• v.22 no.1
• /
• pp.107-118
• /
• 2016

The advent of 5G mobile communications, which is expected in 2020, will provide many services such as Internet of Things (IoT) and vehicle-to-infra/vehicle/nomadic (V2X) communication. There are many requirements to realizing these services: reduced latency, high data rate and reliability, and real-time service. In particular, a high level of reliability and delay sensitivity with an increased data rate are very important for M2M, IoT, and Factory 4.0. Around the world, 5G standardization organizations have considered these services and grouped them to finally derive the technical requirements and service scenarios. The first scenario is broadcast services that use a high data rate for multiple cases of sporting events or emergencies. The second scenario is as support for e-Health, car reliability, etc.; the third scenario is related to VR games with delay sensitivity and real-time techniques. Recently, these groups have been forming agreements on the requirements for such scenarios and the target level. Various techniques are being studied to satisfy such requirements and are being discussed in the context of software-defined networking (SDN) as the next-generation network architecture. SDN is being used to standardize ONF and basically refers to a structure that separates signals for the control plane from the packets for the data plane. One of the best examples for low latency and high reliability is an intelligent traffic system (ITS) using V2X. Because a car passes a small cell of the 5G network very rapidly, the messages to be delivered in the event of an emergency have to be transported in a very short time. This is a typical example requiring high delay sensitivity. 5G has to support a high reliability and delay sensitivity requirements for V2X in the field of traffic control. For these reasons, V2X is a major application of critical delay. V2X (vehicle-to-infra/vehicle/nomadic) represents all types of communication methods applicable to road and vehicles. It refers to a connected or networked vehicle. V2X can be divided into three kinds of communications. First is the communication between a vehicle and infrastructure (vehicle-to-infrastructure; V2I). Second is the communication between a vehicle and another vehicle (vehicle-to-vehicle; V2V). Third is the communication between a vehicle and mobile equipment (vehicle-to-nomadic devices; V2N). This will be added in the future in various fields. Because the SDN structure is under consideration as the next-generation network architecture, the SDN architecture is significant. However, the centralized architecture of SDN can be considered as an unfavorable structure for delay-sensitive services because a centralized architecture is needed to communicate with many nodes and provide processing power. Therefore, in the case of emergency V2X communications, delay-related control functions require a tree supporting structure. For such a scenario, the architecture of the network processing the vehicle information is a major variable affecting delay. Because it is difficult to meet the desired level of delay sensitivity with a typical fully centralized SDN structure, research on the optimal size of an SDN for processing information is needed. This study examined the SDN architecture considering the V2X emergency delay requirements of a 5G network in the worst-case scenario and performed a system-level simulation on the speed of the car, radius, and cell tier to derive a range of cells for information transfer in SDN network. In the simulation, because 5G provides a sufficiently high data rate, the information for neighboring vehicle support to the car was assumed to be without errors. Furthermore, the 5G small cell was assumed to have a cell radius of 50-100 m, and the maximum speed of the vehicle was considered to be 30-200 km/h in order to examine the network architecture to minimize the delay.

• The Korean Journal of Air & Space Law and Policy
• /
• v.20 no.1
• /
• pp.9-43
• /
• 2005

The Korean government established her first "National Space Program" in 1996, and revised it in 2000 and 2005. As embedded in the National Space Program, Korea aims to become one of the world's top countries in space technology by 2010. All of 13 satellites are planned to be put into orbit as schematized, which include 7 multi-purpose satellites, 4 science satellites and 2 geostationary orbit satellites. The Space Center in Korea is to be built at Woinara-Do, Bongrae-Myon, Koheung-Goon, Junlanam Province on the southern coast of the Korean peninsular. The first phase of the construction of the space center will be finished by 2007 for launch of KSLV-l. This will make Korea be the 13th advanced country in space development having a launching site in the world. The "Space Center" will serve as the infrastructure for the development of space technology and related technology, and plan to launch a low earth orbit satellite in 2007. A second science satellite made in Korea will be launched from the space center by 2007. From 2010, the center will be operated on a commercial basis operating launch facilities for low-to mid-altitude orbit satellites. Since the 'Aircraft Industry Promotion Act' was replaced by the 'Aerospace Industry Development Promotion Acf of 1987, this Act had been amended seven times from 1991 year to 2004. Most of developed countries has been enacted the space law including the public or private items such as an (1)DSA, (2)Russia, (3)the United Kingdom, (4)Germany, (5)France, (6)Canada, (7)Japan, (8)Sweden, (9)Australia, (10)Brazil, (11)Norway, (12)South Africa, (13)Argentina, (14)Chile, (15)Ukrainian etc. As the new Space Exploration Promotion Act was passed by the resolution of the Korean Congress on May 3, 2005, so the Korean government has made the public proclamation the abovementioned Act on May 31, this year. This Act takes effect on December 1, 2005 after elapsing six months from the date of promulgation. The main contents of Space Exploration Promotion Act of 2005 is as the following (1)establishing a basic plan for promoting space exploration, (2)establishment and function of national space committee, (3)procedure and management of domestic and international registration of space objects, (4)licensing of launch by space launch vehicles, (5)lability for damages caused by space accidents and liability insurance, (6) organizing and composition of the space accident investigation committee, (7)Support of non-governmental space exploration project, (8)Requesting Support and Cooperation of Space Exploration, (9)Rescue of Astronauts and Restitution of Space Objects, etc.. In oder to carry out successfully the medium and long basic plan for promoting space exploration and to develope space industry in Korea, I think that it is necessary for us to enlarge and to reorganize the function and manpower of the Space Technology Development Division of the Ministry of Science & Technology and the Korea Aerospace Research Institute. Korea has been carrying out its space program step by step according to the National Space Program. Korea also will continually strengthen the exchange and cooperation with all the countries in the world under the principle of equality, friendship relations and mutual benefits. Together with all other peoples around the globe, Korea will make due contribution towards the peaceful utilization of space resources and promotion of human progress and prosperity.

• KDI Journal of Economic Policy
• /
• v.13 no.1
• /
• pp.3-33
• /
• 1991

Since the early 1980's, the Korean government has gradually been widening the Korean market to foreign consumer goods. This, combined with the increased purchasing power of the Korean consumers resulting from the continued economic growth of the country, has sparked a spectacular influx of foreign consumer goods into Korea, ranging from BMW's to chopsticks. Import of foreign consumer goods amounted to more than 6 billion dollars in 1989 and is continuing to grow at a rapid rate. The increased import of foreign consumer goods doubtlessly improved the overall welfare of the Korean consumers by providing them with a wider range of options to choose from, by lowering the prices of some of the consumer goods domestically produced, and also by forcing the producers of some Korean goods to face competition with better foreign goods, thus giving them an incentive to raise the quality of their products. However, it is agreed by most economists that this increase in general welfare has been much smaller than what they had expected at the outset. Consumer prices of most imported consumer goods are easily double the import price, and in some cases, more than treble the import prices. Further, there has not been a noticeable drop in the prices of domestically produced consumer goods. Much of the blame has been attributed to the distribution sector of Korea. The objective of this paper is to analyze the imported consumer goods distribution sector of Korea, focusing on the possible sources of the poor performance of that sector, and to make policy suggestions that could potentially increase the welfare. This paper differs from all the previous research by others on this subject in that it analyzes the imported consumer goods distribution sector of Korea as a vertical structure. The distribution sector of an imported consumer good is a vertical structure since it consists of an international market, an import stage, and domestic wholesale and retail markets, in that order vertically. Our study naturally includes the analysis of the vertical restraints as well as the analysis of the industrial organization of each horizontal stage in the vertical structure. Each horizontal component of the imported consumer goods distribution sector is basically a monopolistically competitive market differentiated by characteristics of goods and by the locations and the services of firms. Further, restrictive dealership and resale price maintenance are found to be widely in use. Our main findings are the follwing; First, most consumer goods are imported monopolistically or oligopolistically through restrictive dealership contracts between foreign producers and domestic importers. Such restrictive dealership gives importers market power in the domestic market and explains many of the large discrepancies betwen the consumer prices and the import prices of many goods. Korean anti - trust law does not cover the issues arising from the market power of an importer resulting from a restrictive dealership contract. Second, some major producers of Korean goods are also importers of foreign goods that are substitutes of their products. The import of substitutes by major domestic producers is anti - competitive because it tends to raise the prices of both domestic goods and foreign goods, and also because it reduces the incentive of the domestic producers to raise the quality of their products. Third, wholesalers and retailers widely use resale price maintenance as a price fixing mechanism, and while this is against the anti- trust law, it seldom gets noticed. Fourth, the high level of rents of real estate for commercial use works as an entry barrier to the distribution sector and results in reduced competition by the firms in that sector. Finally, there are information problems. Consumers have inferior information to firms about the quality of a foreign consumer good that they have not tried before. Such information asymmetry often enables firms to raise prices. In addition, information asymmetry between importers frequently delays the import of cheaper substitutes. In order to alleviate the problems indentified above, we suggest the following policy changes. The government should strengthen the anti - trust law and its enforcement to regulate restrictive import contracts, import of competing goods by major domestic producers, and RPM by wholesalers and retailers that is aimed at price fixing. In addition, the government should loosen its tight real estate policy to encourage investment in the distribution sector. Finally, we suggest that the import price revelation policy that has been in use for some items since 1990 be expanded to most imported consumer goods that are introduced for the first time to give consumer better information and be used only for the period of time needed to inform sufficient number of consumers.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.42 no.3
• /
• pp.464-477
• /
• 2013

There is a great need to develop a training program proven to change behavior and improve knowledge. The purpose of this study was to evaluate employee hygiene knowledge, hygiene practice, and cleanliness, before and after HACCP system implementation at one small-size restaurant. The efficiency of the system was analyzed using time-temperature control after implementation of u-HACCP$^{(R)}$. The employee hygiene knowledge and practices showed a significant improvement (p<0.05) after HACCP system implementation. In non-heating processes, such as seasoned lettuce, controlling the sanitation of the cooking facility and the chlorination of raw ingredients were identified as the significant CCP. Sanitizing was an important CCP because total bacteria were reduced 2~4 log CFU/g after implementation of HACCP. In bean sprouts, microbial levels decreased from 4.20 logCFU/g to 3.26 logCFU/g. There were significant correlations between hygiene knowledge, practice, and microbiological contamination. First, personnel hygiene had a significant correlation with 'total food hygiene knowledge' scores (p<0.05). Second, total food hygiene practice scores had a significant correlation (p<0.05) with improved microbiological qualities of lettuce salad. Third, concerning the assessment of microbiological quality after 1 month, there were significant (p<0.05) improvements in times of heating, and the washing and division process. On the other hand, after 2 months, microbiological was maintained, although only two categories (division process and kitchen floor) were improved. This study also investigated time-temperature control by using ubiquitous sensor networks (USN) consisting of an ubi reader (CCP thermometer), an ubi manager (tablet PC), and application software (HACCP monitoring system). The result of the temperature control before and after USN showed better thermal management (accuracy, efficiency, consistency of time control). Based on the results, strict time-temperature control could be an effective method to prevent foodborne illness.