• Journal of the Korean Chemical Society
• /
• v.31 no.1
• /
• pp.102-109
• /
• 1987

Some characteristics of $SnO_2$ film which was deposited on a slide glass substrate, using dibutyl tin diacetate and oxygen, by the chemical vapor deposition were observed. The optimum condition for the preparation of the film was found to be at 420$^{\circ}C$ of substrate temperature for 20 min of deposition. Important optical, electrical, and structural features of the film were examined. It was found that the typical $SnO_2$ film on the untreated substrate was 4000${\AA}$ in thickness, transmitted 90% of the visible liglit, and provided 5800 ohms/${\square}$ of the sheet resistance. It was also found that the surface treatments of the slide glass by acid leaching were beneficial. The film structure was found to be a mixture of polycrystalline tetragonal stannic oxide confirmed by the X-ray diffraction and to be spherical fine grains concluded by the scanning electron microscopy.

• Journal of Bio-Environment Control
• /
• v.18 no.4
• /
• pp.475-480
• /
• 2009

These studies were carried out to find the effect of packing materials and storage temperature to enhance the storability of Salicornia europaea. The fresh weight loss was less than 2% at below $10^{\circ}C$ and non-perforated package, but $25^{\circ}C$ and perforated package treatment showed more than 4% of fresh weight loss that result to deteriorate quality. The carbon dioxide and oxygen contents remained 1~2% and above 15% in non-perforated package, and these contents were in proportion to gas permeability of packing materials. All the temperature treatments except 25c showed rapidly increasing ethylene concent from 7days after storage, and the highest ethylene content was $2^{\circ}C$ treatment that should appear chilling injury. The off-odor and deterioration ratio were lowest in $5^{\circ}C$ among the temperature treatments and $50{\mu}m$ thickness ceramic film treatment at $5^{\circ}C$ storage, while packing materials did not show any trends among the temperature treatments. The shelf life based on visual quality showed highest in $50{\ss}|$ thickness ceramic film packing and $5^{\circ}C$ treatment, and that was 28days.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.23 no.1
• /
• pp.9-15
• /
• 2017

To identify applicability for packaging material of polyvinyl alcohol (PVA)/boric acid (BA) coating solution with highly-enhanced water vapor and oxygen barrier properties, the PET/PVA-BA/OPP multi-layer films were prepared through comma coating and lamination process. The oxygen and water vapor permeabilities, and tensile strength of as-prepared multi-layer films were investigated before and after pressure cooker test (PCT). Although oxygen and water vapor permeabilites, and mechanical properties of PET/PVA-BA/OPP multi-layer films was decreased after PCT, their properties were highly enhanced as increase of BA contents in PVA matrix. This is strongly related with enhanced cross-linking density in PVA-BA layer. In storage test of seasoned-laver, the PET/PVA-BA/OPP multi-layer films were comparatively effective to suppress the increase in peroxide value originating from oxidation of seasoned-laver. Comparing the commercially available PP/Al-metallized PP for seasoned-laver packaging, however, PET/PVA-BA/OPP multi-layer films did not show any advantage in water activity. This is due to higher water vapor permeation properties of as-prepared multi-layer films. Therefore, further studies are required to enhance the water vapor permeation in PET/PVA-BA/OPP multi-layer films.

• Journal of Bio-Environment Control
• /
• v.23 no.2
• /
• pp.116-122
• /
• 2014

This study was conducted to find out the appropriate packaging materials to extend the storability and maintain the quality of cherry tomato for modified atmosphere (MA) storage. Tomatoes were grown by hydroponic at a plastic house in Gangwon Province. Light red maturity stage tomatoes were harvested and packed with MA condition (10,000; 20,000; 40,000; 60,000; 80,000; and $100,000cc/m^2.day.atm$ $O_2$ permeability film) and perforated film to store at $5^{\circ}C$, $11^{\circ}C$ and $24^{\circ}C$. The fresh weight loss was less than 0.6% in all non-perforated breathable films at $^5{\circ}C$, $11^{\circ}C$, and $24^{\circ}C$, but perforated film had less than 2.93% at $5^{\circ}C$, 13.29% at $11^{\circ}C$ and 27.24% at $24^{\circ}C$. The 20,000cc at $5^{\circ}C$ and $11^{\circ}C$, and the 40,000cc film at $24^{\circ}C$ balanced optimum carbon dioxide and oxygen concentration in the package to maintain quality. The 10,000cc film was appeared the significantly highest ethylene concentration at $5^{\circ}C$, $11^{\circ}C$, and $24^{\circ}C$, this film had the lowest $O_2$ permeability. Visual quality, firmness, and soluble solids were maintained in 20,000cc films both at $5^{\circ}C$ and $11^{\circ}C$, the 40,000cc film at $24^{\circ}C$. There was no any trend in titratable acidity and vitamin C content of treated packed film types and temperatures at cherry tomatoes packages. Therefore, the appropriate MA condition for $5^{\circ}C$ and $11^{\circ}C$ is $20,000cc/m^2.day.atm$ $O_2$ permeability film; for $24^{\circ}C$ it is $40,000cc/m^2.day.atm$ $O_2$ permeability film because those films extended the storability through the firmness, soluble solids as well as visual quality.

• Korean Journal of Weed Science
• /
• v.6 no.2
• /
• pp.110-123
• /
• 1986

To know the ecological pattern of bulrush (Scirpus juncoides Roxb.) seeds and overwintreed stumps in germination and sprouting responses as affected by different temperature (7 trt.), light intensity (5 trt.), shading intensity (S trt.), light quality (specturm spectrum; 6 trt.), soil acidity (7 trt.), stump sizea (weight base; 5 trt.), and molding depth (6trt.), respectively, this serial studies were conducted by use of growth chamber, incubator, Wagner pot and petri-dish. Most efficient treatment was obtained from 25-$35^{\circ}C$ temperature, higher light intensity in 2-11 klux range, 95% shading intensity, clear and yellow film for seeds/clear and blue film for stumps, soil pH 5.53, 3-4g stump weight, 0-5% wxygen concentration, 1 ㎝ flooding depth for seeds, and 1-1.5cm molding depth for seeds/0.5-1.0 cm molding depth for stumps, respectively, among others.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.12 no.2
• /
• pp.84-90
• /
• 2009

We incubated marine columnar sediments at $25^{\circ}C$ for 230 days to simulate the responses of phosphorus in the sediment which was exposed to freshwater. The incubation was composed of three different treatments (FW: freshwater, FWA: freshwater under anoxic condition, and SW: seawater as a Control). Six particulate fractions of phosphorus in sediment were obtained through sequential extraction and, for comparison, phosphate concentrations in porewater and superlying water were also determined. After the incubation, evidently higher concentrations of phosphate were found in FW and FWA compared to SW. Mass extinction of living organisms in marine sediment from freshwater shock and consequent decay of their corps probably contributed such high phosphate spike in the overlying water. Higher concentrations of BD-P(lron-bound P) were found in FW compared to SW. After exposure to the freshwater, we could determine that penetration depth of dissolved oxygen in marine sediment will be deeper. A result of increases of ferrous compounds in freshwater where contained less sulfide has been obtained. Because of these phenomena, BD-P was increased in FW. On the contrary, BD-P was decreased in FWA since poor dissolved oxygen concentration. In FWA, total amount of Leachable P(SUM of LOP) has been remarkably increased through the experiment, which strongly suggested the easy conversion of the leachable P into reactive P. This experiment has shown that most of diverse P species in marine sediment were leachable under freshwater and low oxygen condition. Therefore reclamation of natural tidalfalt and consequent freshwater introduction seems to trigger the conversion of diverse P-species to leachable P in the marine sediments, which will exert high benthic load of phosphate to the overlying water.

• Membrane Journal
• /
• v.27 no.2
• /
• pp.154-166
• /
• 2017

Polymeric films for gas barrier applications such as food packaging and electronic devices have attracted great interest due to their cheap, light and easy processability among gas barrier materials. Especially in electronic devices, extremely low gas permeance is necessary for maintaining the device performance. However, current polymeric barrier films still suffer from relatively high gas permeance than other materials. Therefore, there have been strong needs to enhance the gas barrier performance of polymeric barrier films while keep their own advantages. Recently, graphene is highlighted as a 2D-layered material for gas barrier applications. However, owing to the poor workability and difficulty to produce in engineering scale, graphene oxide (GO) is on the rise. GO consists of oxygen-containing functional groups on surface with intrinsic 2D-layered structure and high aspect ratio, and it can be well-dispersed in aqueous polar solvents like water, resulting in scalable mass production. Here, we prepared GO incorporated polyimide (PI) nanocomposites. PI is widely used barrier polymer with high mechanical strength and thermal and chemical stability. We demonstrated that PI/GO nanocomposites could perform as a gas barrier. Furthermore, surfactants (Triton X-100 (TX) and Sodium deoxycholate (SDC)) are introduced to enhance the gas barrier performance by improving the degree of dispersion of GO in PI matrix. As a result, TX enhanced the gas barrier performance of PI/GO nanocomposites which is similar to predicted value. This finding will provide new insight to polymer nanocomposites for gas barrier applications.

• Membrane Journal
• /
• v.17 no.2
• /
• pp.124-133
• /
• 2007

In this study, we treated lake water by 2 kinds of multichannel ceramic micro filtration membranes. We could investigate effects of $N_2-back-flushing$ time (BT) and transmembrane pressure (TMP), and find optimal operating conditions. The BT were changed in $10{\sim}60$ sec, TMP in $0.6{\sim}2.0$ bar at fixed filtration time (FT) 8 min, flow rate 2.0 L/min and back-flushing pressure 2.0 bar. Also, the optimal conditions were discussed in the viewpoints of resistance of membrane fouling $(R_f)$, dimensionless permeate flux $(J/J_o)$, permeate flux (J) and total permeate volume $(V_T)$. As result, optimal back-flushing conditions for HC04 ($0.4{\mu}m$ pore size) and HC10 membrane $(1.0{\mu}m)$ were BT=10 sec and BT=20 sec, respectively. Then, higher TMP should increase the driving force, and could produce more VT. Average rejection rates of pollutants were higher than 95.4% for turbidity, $12.7{\sim}20.1%\;for\;COD_{Mn},\;0.0{\sim}6.4%\;for\;NH_3-N,\;1.9{\sim}4.6%$ for T-N and $34.9{\sim}88.4%$ for T-P.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.405-406
• /
• 2013

Ga-doped ZnO (GZO)는 $300^{\circ}C$ 이상의 온도에서는 전기적으로 불안정하기 때문에 CIGS, CdTe, DSC와 같은 태양전지의 높은 공정온도 때문에 사용이 제한적이다. ZTO thin film은 Al2O3, SiO2, TiO2, ZnO tihin film과 비교하여 산소 및 수분에 대하여 투과성이 상대적으로 낮은 것으로 알려져 있다. 따라서 GZO single layer에 비하여 ZTO-GZO multi-layer를 구성하여 TCO를 제작하면, 높은 공정온도에서도 사용 가능하다. 실제 제작된 GZO single layer (300 nm)에서 비저항이 $7.69{\times}10^{-4}{\Omega}{\cdot}cm$에서 $500^{\circ}C$에서 열처리 후 $7.76{\times}10^{-2}{\Omega}{\cdot}cm$으로 급격하게 상승한다. ZTO single layer (420 nm)는 as-grown에서는 측정 불가했지만, $400^{\circ}C$에서 열처리 후 $3.52{\times}10^{-1}{\Omega}{\cdot}cm$ $500^{\circ}C$에서 열처리 후 $4.10{\times}10^{-1}{\Omega}{\cdot}cm$으로 열처리에 따른 큰 변화가 없다. 또한 ZTO-GZO multi-layer (720 nm)의 경우 비저항이 $2.11{\times}10^{-3}{\Omega}{\cdot}cm$에서 $500^{\circ}C$에서 열처리 후 $3.67{\times}10^{-3}{\Omega}{\cdot}cm$으로 GZO에 비하여 상대적으로 변화폭이 작다. 또한 ZTO의 두께에 따른 영향을 확인하기 위하여 ZTO를 2 scan, 4 scan, 6 scan 공정 진행 및 $500^{\circ}C$에서 열처리 후 ZTO, ZTO-GZO thin film의 비저항을 측정하였다. ZTO의 경우 $3.34{\times}10^{-1}{\Omega}{\cdot}cm$ (2 scan), $3.62{\times}10^{-1}{\Omega}{\cdot}cm$ (4 scan), $4.1{\times}10^{-1}{\Omega}{\cdot}cm$ (6 scan)으로 큰 차이가 없으며, ZTO-GZO에서도 $3.73{\times}10^{-3}{\Omega}{\cdot}cm$ (2 scan), $3.42{\times}10^{-3}{\Omega}{\cdot}cm$ (4 scan), $3.67{\times}10^{-3}{\Omega}{\cdot}cm$ (6 scan)으로 큰 차이가 없음을 확인하였다. 염료감응 태양전지에 적용하여 기존에 사용되는 FTO대신에 ZTO-GZO를 사용하며, 가격적 측면, 성능적 측면에서 개선 가능할 것으로 생각된다.

• Membrane Journal
• /
• v.12 no.2
• /
• pp.107-119
• /
• 2002

Carbon-silica ($C-SiO_2$) membranes can be easily prepared by the pyrolysis of two-phase copolymers containing an aromatic imide block and a siloxane block and remarkably high permselectivities of $He/N_2, O_2/N_2,$ and $CO_2/N_2$. The pyrolysis of the imide-siloxane block copolymers was carried out at different final temperatures, $600^{\circ}C, 800^{\circ}C,$ and $1000^{\circ}C$ under an inert atmosphere, and is the first reported case of the precursors being used for the preparation of carbon membrane. The polymeric precursors were synthesized in a wide range of siloxane content and different final morphology, and the pyrolozed membranes were tested with a high vacuum time-lag method at $25^{\circ}C$ and 76cmHg of feed pressure. In experiments with He, $CO_2, O_2 \;and \;N_2$, the membranes were found to have good $O_2/N_2$ selectivity up to 32.2 and $O_2$ permeability on the order of $10-8/cm^2(STP)cm/cm^2seccmHg.$.