• Journal of the Korean Ceramic Society
• /
• v.39 no.6
• /
• pp.582-588
• /
• 2002

IrO$_2$-RuO$_2$ films were deposited on plasma sprayed TiO$_2$ buffer layer above Ti metal by sol-gel and dip-coating method. Organic vehicle (ethyl cellulose and $\alpha$-terpineol) and glass frit were added to improve adherence of the coatings. Taguchi method and L$_{18}$ (2$^1$$\times$3$^{7}$ ) orthogonal arrays were evalvated in terms of current density to determine the optimal combination of levels of factors that best satisfy the bigger is better quality characteristic. The observed conditions were as fellows: ethyl cellulose (100 cp), drying temperature and time (17$0^{\circ}C$,20 min), heat treatment temperature and time (75$0^{\circ}C$,10 min), the weight ratio of IrO$_2$-RuO/powders to glass frit (99:5), final heat treatment time (120 min) and flow rate of air (5 sccm), respectively. ANOVA analysis suggested that the influence of the factors within $\alpha$= 0.1 was significant with a 90% confidence level.

• Composites Research
• /
• v.32 no.6
• /
• pp.355-359
• /
• 2019

The high efficient water splitting system should involve the reduction of high overpotential value, which was enhanced by the electrocatalytic reaction efficiency of catalysts, during the hydrogen evolution reaction (HER) and the oxygen evolution reaction (OER) reaction, respectively. Among them, transition metal-based compounds (oxides, sulfides, phosphides, and nitrides) are attracting attention as catalyst materials to replace noble metals that are currently commercially available. Herein, we synthesized optimal monodisperse Co₃[Co(CN)₆]₂ PBAs by FESEM, and confirmed crystallinity by XRD and FT-IR, and thermal behavior of PBAs via TG-DTA. Also, we synthesized monodispersed Co₃O₄ nanocubes by calcination of Co₃[Co(CN)₆]₂ PBAs, confirmed the crystallinity by XRD, and proceeded OER measurement. Finally, the synthesized Co₃O₄ nanocubes showed a low overpotential of 312 mV at a current density of 10 mA·cm^-2 with a low Tafel plot (96.6 mV·dec^-1).

• Membrane Journal
• /
• v.27 no.2
• /
• pp.154-166
• /
• 2017

Polymeric films for gas barrier applications such as food packaging and electronic devices have attracted great interest due to their cheap, light and easy processability among gas barrier materials. Especially in electronic devices, extremely low gas permeance is necessary for maintaining the device performance. However, current polymeric barrier films still suffer from relatively high gas permeance than other materials. Therefore, there have been strong needs to enhance the gas barrier performance of polymeric barrier films while keep their own advantages. Recently, graphene is highlighted as a 2D-layered material for gas barrier applications. However, owing to the poor workability and difficulty to produce in engineering scale, graphene oxide (GO) is on the rise. GO consists of oxygen-containing functional groups on surface with intrinsic 2D-layered structure and high aspect ratio, and it can be well-dispersed in aqueous polar solvents like water, resulting in scalable mass production. Here, we prepared GO incorporated polyimide (PI) nanocomposites. PI is widely used barrier polymer with high mechanical strength and thermal and chemical stability. We demonstrated that PI/GO nanocomposites could perform as a gas barrier. Furthermore, surfactants (Triton X-100 (TX) and Sodium deoxycholate (SDC)) are introduced to enhance the gas barrier performance by improving the degree of dispersion of GO in PI matrix. As a result, TX enhanced the gas barrier performance of PI/GO nanocomposites which is similar to predicted value. This finding will provide new insight to polymer nanocomposites for gas barrier applications.

• Membrane Journal
• /
• v.29 no.1
• /
• pp.51-60
• /
• 2019

In order to improve gas separation properties of polymeric membranes which have been widely applied in the industry field, aluminosilicate hollow nanoparticles named as allophanes were synthesized by sol-gel method and formulated in Poly(dimethylsiloxane) (PDMS) matrix to investigate the gas separation properties of PDMS membrane. Transmission electron microscope (TEM), Energy dispersive X-ray analysis (EDX), X-ray diffractometer (XRD), Surface area and pore size analyzer (BET) and Fourier transform infrared spectrophotometer (FTIR) were carried out to characterize the synthetic allophanes. Then the PDMS mixed matrix membranes were prepared by adding different volume fraction of allophanes. To examine the effect of allophanes addition in PDMS matrix using unmodified allophane and modified ones, the gas permeation experiments were performed using oxygen, nitrogen, methane and carbon dioxide. As the volume fraction of modified allophane increased up to 4.05 Vol% the permeability of four test gases through PDMS mixed matrix membranes increased. Also, the selectivity of $O_2/N_2$ and $CO_2/CH_4$ increased with the contents of the modified allophane. Further improvement of gas separation properties of PDMS mixed matrix membranes containing higher volume percent of allophanes can be expected as long as well dispersion of allophanes in PDMS matrix can be achieved for better PDMS membranes.

• Korean Chemical Engineering Research
• /
• v.57 no.4
• /
• pp.512-518
• /
• 2019

To develop a membrane electrode assembly (MEA) with lower Pt loading and higher performance in proton exchange membrane fuel cells (PEMFCs), it is an important research issue to understand interfacial structure of Pt/C catalyst and ionomer and design the catalyst layer structure. In this study, we prepared short-side-chain Nafion-based ionomer dispersion using propylene glycol (PG) as a solvent instead of water which is commonly used as a solvent for commercially available ionomers. Cathode catalyst layers with different ionomer content from 20 to 35 wt% were prepared using the ionomer dispersion for the fabrication of four different MEAs, and their fuel cell performance was evaluated. As the ionomer content increased to 35 wt%, the performance of the prepared MEAs increased proportionally, unlike the commercially available water-based ionomer, which exhibited an optimum at about 25 wt%. Small size micelles and slow evaporation of PG in the ionomer dispersion were effective in proton transfer by inducing the formation of a uniformly structured catalyst layer, but the low oxygen permeability problem of the PG-based ionomer film should be resolved to improve the MEA performance.

• Applied Chemistry for Engineering
• /
• v.21 no.1
• /
• pp.58-62
• /
• 2010

CNT-$TiO_{2}$ nano complexes were prepared from $TiOSO_4$ and multi-walled carbon nanotube (MWCNT) by hydrolysis. The CNTs were dispersed uniformly with anatase $TiO_{2}$ in the prepared $TiO_{2}$-CNT complexes. The increasing MWCNT ratio leads to increased crystalline carbon and O/Ti ratio. The decomposition degree of methylene blue was experienced according to UV radiation time for study adsorption and photocatalytic activity. The samples having high MWCNT ratio show high adsorption and photodegradation. The high specific surface area, functional group having oxygen, low band gap energy, high electric conductivity, high volume to surface ratio, uniform structure and properties of MWCNT assist photocatalytic activity of CNT-$TiO_{2}$ complex.

• The Journal of the Convergence on Culture Technology
• /
• v.1 no.2
• /
• pp.65-69
• /
• 2015

Teeth and bones are very resistance to high temperatures and remain recognizable even after prolonged exposures to heat. The effects of heating and burning on teeth have been studied with the aim of discerning a characteristic signature withstanding high temperature, but there have been few studies about a human cremated ash, especially Korea. We are recognizable by elemental composition and can be detected in human cremated ash samples by Scanning electromicroscopy/Energy dispersive X-ray spectrometry analysis(SEM/EDS), cremated, at $800{\sim}900^{\circ}C$ for 1 hour. In this temperature range, different crystals morphologies(spherical, irregular and hexagonal) are observed in SEM. Calcium(Ca) and oxygen(O) increases steadily after cremation in EDS. We suggest that cremated bone have been provided with calcium oxide(CaO) formation at temperature above $900^{\circ}C$. This study offers basic data to assess the structure and elemental compositions of human ash and to determine if these remain identifiable after exposure to extreme temperatures.

• Applied Chemistry for Engineering
• /
• v.31 no.1
• /
• pp.108-114
• /
• 2020

In this study, NH₃-selective catalytic oxidation (SCO) efficiencies according to calcination/reduction conditions were compared when preparing various Ru[1]/TiO₂ catalysts. The Ru[1]/TiO₂ red catalyst had better NH₃ conversion and NH₃ to N₂ conversion than those of Ru[1]/TiO₂ cal. Physico-chemical properties of Ru[1]/TiO₂ catalysts were confirmed by Brunauer Emmett Teller (BET), X-ray diffraction (XRD), transmission electron microscope (TEM), X-ray photoelectron spectroscopy (XPS) and temperature programmed reduction (H₂-TPR) analyses, and the properties were shown to affect the dispersion and surface adsorption oxygen species (O_β) ratio of the active metal.

• Journal of the Korean Vacuum Society
• /
• v.10 no.4
• /
• pp.416-423
• /
• 2001

Microstructural, optical and dielectric properties of $SrTiO_3$ thin films were investigated. These films were deposited on the ITO glasses by rf-magnetron sputtering at room temperature and subequently heat treated in $O_2$ atmosphere at various temperatures. It has been found from X-ray diffraction patterns that as-deposited films prepared at room temperature are amorphous, while the films heat treated at temperature range of 400~$600^{\circ}C$ reveal the structure of pyrochlore. On the other hand, the structure of perovskite is dominantly observed in the films heat treated at temperatures over $650^{\circ}C$ in which the drastic changes of optical band gap and dielectric constant are observed. In addition, the phase transition peak is observed at $272^{\circ}C$ in the films heat treated at $600^{\circ}C$, while the dielectric dispersion is observed at near $310^{\circ}C$ in the films heat treated at $650^{\circ}C$.

• Journal of the Mineralogical Society of Korea
• /
• v.15 no.1
• /
• pp.44-58
• /
• 2002

A new polymorph of tridymite, an incommensurately modulated phase (IC phase), has been identified. While the symmetry of the IC lattice is same as that of the Ll phase, the geometry of the IC lattice structure is same as the basis of the L3 structure with a different modulation (modulation vector q=0.22 $c*_{H}$;$\lambda$ 37 ). On the other hand, the characteristic curved diffuse diffration observed from the Ll atoms could occur even at room phase suggests that the dynamic disordering of atoms, especially oxygen atoms could occur even at room temperature. The phase transition of Ll to L3 by grinding is gradual but very conspicuous: LllongrightarrowL1+IClongrightarrowIC+L3longrightarrowL3. However, it is revealed that real transition processes of individual grains are directly related to the local stress fields and preexisting microstructures.