• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2857-2861
• /
• 2007

Flow and aerodynamic characteristics were analyzed numerically for a commercial passenger airplane, Boeing 747-400, flying in the cruising condition. The model geometry with 100:1 in scale was obtained by the photo scanning measurement with the maximum error of 1.4% comparing with the real airplane dimension. The three-dimensional inviscid steady compressible governing equations were solved by the finite volume method in the unstructured grid system. The convective terms were treated by the Crank-Nicholson and first-order upwind schemes. In the computational results, the strong wing-tip vortices were clearly observed and the pressure contours on the airplane surface were suggested. The lift and drag forces in the wing with engines increase by 1.49% and 3.9%, respectively compared with the case without engines. The aerodynamic forces were estimated quantitatively for each element which consists of the airplane.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.1351-1360
• /
• 2005

New construction for public transport in congested urban areas will involve tunnel construction adjacent to existing building or bridge foundations and services due to the lack of surface space. Therefore, careful assessment of the important underground structure-soil-tunnelling interaction is relatively new, currently only limited information is available. In this study, the authors carried out FE analysis and the laboratory model test using the photogrammetric technique and suggested the influence zones associated with the normalised pile tip settlement during new tunnel construction.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.37 no.6
• /
• pp.555-562
• /
• 2019

This paper presents soil deformation measurement in model chamber based on photogrammetry. We created an aluminum framed acrylic model chamber with soil inside and applied photogrammetry to measure soil deformation caused by loading tests. The soil consists of 40% black and 60% regular sand to create image contrast in soil images. In preprocessing, the self camera calibration was carried out for IOPs (Interior Orientation Parameters), followed by the space resection to estimate EOPs (Exterior Orientation Parameters) using control points located along the aluminum frame. Image matching was applied to measure the soil displacement. We tested different matching window sizes and the effect of image smoothing. Experimental results showed that 65x65 pixels of window size produced better soil deformation map and the image smoothing was useful to suppress the matching outliers. In conclusion, photogrammetry was able to efficiently generated soil deformation map.

• The korean journal of orthodontics
• /
• v.27 no.3 s.62
• /
• pp.421-430
• /
• 1997

Alveolar bone grows with development of tooth germs and roots; bone deposition occurs with tooth eruption. Bone components undergoes processes of resorption and deposition, and when the balance between them is disrupted, decrease in alveolar bone height or excessive bone deposition result. It has been hon that repositioning of teeth through orthodontic treatment can cause alveolar bone resorption which result in decreased alveolar bone height, and there have been many studies to evaluate such effects. X-ray films that could be replicated and standardized were chosen in clinical studies, and among them, bitewing films were used for objective evaluation of changes in alveolar bone level. Twenty subjects, 10 to 13-year- old (average 12.2) children with Cl I molar key, healthy oral condition, no congenital missing, no periodontal disease, and pre-and post-orthodontic bitewing films, were randomly selected for comparison of alveolar bone heights. Amounts of tooth and changes in alveolar bone heights were analyzed. The following results were obtained: 1. Amount of tooth movement in canine, premolar, and molar regions, changes in tooth axis, and changes in alveolar bone heights were measured, and the mean and median values were obtained. 2. When pre-and post-orthodontic alveolar bone levels were compared, larger changes were noticed in maxilla than mandible. 3. When mesio-distally compared, larger changes were observed in the distal sides of 3D3 and 4M3, mesial sides of 4M3 and 4D3, distal sides of 4D3 and 5M3, mesial sides of 5M3 and 5D3, md distal sides of 5D3 and 6M3. 4. When the amounts of tooth movements(TX, TY)and changes in tooth axis(A) were compared,34TX, 34TY, 34A of both sides in maxilla were greater, iud changes in alveolar bone level were greater than any other region.

• The korean journal of orthodontics
• /
• v.29 no.3 s.74
• /
• pp.317-325
• /
• 1999

In proper diagnosis of skeletal Class III malocclusion, it was important to know the pattern of three dimensional skeletal & facial disharmony. The purpose of this study was to obtain P-A cephalometric characteristics in skeletal Class III malocclusion comparing with normal occlusion. The samples were consisted of 120 subjects, divided into four groups : Male normal occlusion, Female normal occlusion, Male skeletal Class III malocclusion, Female skeletal Class III malocclusion. Posteroanterior and lateral cephalogram were taken from the subjects with a x-ray apparatus (ASHAI CX90SP, Japan) and traced on acetate paper with routine manner. The transverse and vertical values from posteroanterior cephalometry, the sagittal values from lateral cephalometry and their ratio were obtained. The results were as follows: 1. The anteroposterior discrepancy in skeletal Class III group was not due to short maxillary length(Cd-A), but to longer mandibular length(Cd-Gn) than normal occlusion group. 2. The faces of skeletal Class III group were longer than normal occlusion group. It was not due to increase of upper face height(Cg-ANS) but to increase of the lower face height(ANS-Me) especially mandibular height(Cd-Me). 3. There was no difference in the facial width values between normal occlusion group and skeletal Class III group, except upper molar width(U6-U6), lower molar width(L6-L6) and mandibular width(Ag-Ag) of female skeletal Class III group which were larger than normal occlusion group. 4. The increase of mandibular length of skeletal Class III group was reflected in the increase of lower facial height but did not have an effect on the mandibular width.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.19 no.3
• /
• pp.355-373
• /
• 2017

Tunnelling in urban areas, it is essential to understand existing structure-tunnel interactive behavior. Serviced structures in the city are supported by pile foundation, since they are certainly effected due to tunnelling. In this research, thus, pile load distribution and ground behavior due to tunnelling below grouped pile were investigated using laboratory model test. Grouped pile foundations were considered as 2, 3 row pile and offsets (between pile tip and tunnel crown: 0.5D, 1.0D and 1.5D for generalization to tunnel diameter, D means tunnel diameter). Soil in the tank for laboratory model test was formed by loose sand (relative density: Dr = 30%) and strain gauges were attached to the pile inner shaft to estimate distribution of axial force. Also, settlements of grouped pile and adjacent ground surface depending on the offsets were measured by LVDT and dial gauge, respectively. Tunnelling-induced deformation of underground was measured by close range photogrammetric technique. Numerical analysis was conducted to analyze and compare with results from laboratory model test and close range photogrammetry. For expression of tunnel excavation, the concept of volume loss was applied in this study, it was 1.5%. As a result from this study, far offset, the smaller reduction of pile axial load and was appeared trend of settlement was similar among them. Particulary, ratio of pile load and settlement reduction were larger when the offset is from 0.5D to 1.0D than from 1.0D to 1.5D.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.47 no.4
• /
• pp.377-388
• /
• 2020

The aim of this study was to evaluate the association between various predicting tools and Apnea-Hypopnea Index (AHI) to identify children with sleep disordered breathing (SDB). From 5 to 10 years old who came for orthodontic counseling, 61 children, whom had lateral cephalograms, pediatric sleep questionnaire (PSQ) records, and portable sleep monitoring results, were included in this study. A total of 17 measurements (11 distances and 6 angles) were made on lateral cephalograms. The measurements of lateral cephalograms, PSQ scales and portable sleep monitoring results were statistically analyzed. 49 of 61 (80%) patients showed AHI > 1, which suspected to have SDB and their mean AHI was 2.75. In this study, adenoid size (A/N ratio), position of the hyoid bone from mandibular plane, gonial angle, and PSQ scale were related to a higher risk of pediatric SDB. Also, oxygen desaturation index (ODI) and snoring time from sleep monitoring results were statistically significant in children with SDB using Mann-Whitney test (p < 0.05). In conclusion, evaluation of hyoid bone position, adenoidal hypertrophy, gonial angle in lateral cephalogram, and PSQ scale was important to screen out potential SDB, especially in children with frequent snoring.

• The korean journal of orthodontics
• /
• v.22 no.3 s.38
• /
• pp.735-753
• /
• 1992

The purpose of this study was to analyze the positions of upper and lower incisors according to facioskeletal patterns. The lateral cephalometric radiographs of sixty persons with normal occlusion, forty persons with Class II Division 1 malocclusion, and forty persons with Class III malocclusion all above the age of 18, were analyzed. The following results were obtained. 1. C I angle, the measurement related to masticatory system, were $89.20{\pm}4.34^{\circ}$ in normal occlusion group, $81.68{\pm}士5.95^{\circ}$ in Class II Division 1 malocclusion group and $101.96{\pm}6.31^{\circ}$ in Class III malocclusion group. 2. In comparison with the positions of upper and lower incisors according to facioskeletal patterns, Class II Division 1 malocclusion group showed that upper incisors were different significantly in all measurements and inclined labially (P < 0.05). Lower incisors were different significantly in all measurements except LI-APog, LI-APog (mm), LI-AB, LI-AB (mm) and inclined labially (P < 0.05), Class III malocclusion group showed that upper incisors were different significantly in all measurements except UI-SN, UI-OP, and inclined labially (P < 0.05). Lower incisors were different significantly in all measurements and inclined lingually (P < 0.05). 3. In all facioakeletal patterns, LI-SN and LI-PH ware correlated moderately to facioskeletal measurements, and FMA was correlated moderately to measurements of lower incisor position. 4. Regardless of the facioskeletal patterns, the reference planes equally applicable were AB line in the measurements of upper incisor and APog line in the measurements of lower incisor.

• The Research Journal of the Costume Culture
• /
• v.5 no.1
• /
• pp.151-164
• /
• 1997

This study pursues the problems of plan photogrammetry which is widely used in somatotyping at present, and find out a method which can improve accuracy of measurement on the basis of principles and mechanisms of photography-the basic foundation of the photographic analysis methods. As a result, this study proposes a new method which is based on the reference point method and perspective coordinate system. And the test measurement was operated to compare the measurement accuracy of the proposed method and the method based on reference grid screen method and perpendicular coordinate system which is commonly used at present. The result of this test measurement showed that the proposed method has higher accuracy. Two reasons can be pointed out for the improvement of measuring accuracy. The first reason is that the proposed perspective coordinate system reduces the perspective distortion of photography. And second reason is that measuring points can be closely placed to the scale and coordinate reference plan of measurement by the proposed reference point method which make possible to place measuring object (or person) at the center of scale and coordinate reference plan by utilizing reference points of measurement in the three dimensional space not on screen.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.05a
• /
• pp.217-222
• /
• 2004

사진 측광은 일시에 대량의 데이터를 얻을 수 있으므로 시간에 따라 빛이 변화하는 주광의 측정 수단으로 이용될 수 있다. 이를 위하여 자연광 아래에서 디지털 이미지와 휘도 측정치의 보정실험을 행하였으나 청공광과 백색시료를 제외한 나머지 시료에 대해서는 그리 만족스러운 결과를 가져오지 못하였다. 앞으로 Videophotometry를 실현하기 위해서는 피 계측면의 분광 반사특성에 의한 계측치의 오차를 제거하기 위한 CCD 소자의 시감도 보정, 시야를 정확하게 재현하기 위한 광학적 연구, 인간의 시각 특성에 부합하는 측정 휘도의 보정 등에 대한 연구가 이루어져야 할 것이다.