• The Journal of the Acoustical Society of Korea
• /
• v.17 no.8
• /
• pp.41-47
• /
• 1998

이중 통신(Duplexer) 필터를 설계 및 개발하기 위한 최적조건을 구하기 위해 36° LiTaO3 기판 표면에 빗살무늬 변환기를 사용한 모의 실험을 수행하였으며, 전극 재료로는 Cu-Al(W3%)합금을 이용하였다. 제작한 듀플렉스 필터의 사다리(Lader)형 구조로서 직렬 공진기와 병렬 공진기의 결합으로 필터를 구성하였다. 적절한 통과대역과 저지대역을 형성 하기 위하여 직렬 공진기와 병렬 공지기의 주파수 차이를 30MHz로 했으며, 낮은 저지대역 을 형성하기 위하여 두 공진기의 전기용량의 비는 1로 하였고, 전극의 두께는 2,500Å으로 하였을 때 설계 조건과 일치하는 주파수 응답을 얻었다. 제작한 듀플렉서 필터의 주파수 특 성은 중심 주파수는 836.5MHz와 881.5MHz, 통과대역 폭은 25MHz, 삽입손실은 2.5dB 이하 및 저지대역은 -35dB이하로 나타났다.

• Fire Science and Engineering
• /
• v.29 no.1
• /
• pp.73-79
• /
• 2015

There are three kinds of design method of the fire sprinkler systems. Grid type is connected all branch as a trapezoid. Loop type is connected cross-mains like circle. The last one is a tree type most commonly used. Grid type needs computer program to calculate the friction loss and flow rate apart from very simple form. In loop type, manual calculation is possible. Design engineer can draw up and calculate the demands without computer program. Because water supplies two direction in loop type, friction loss is smaller than tree type. Water distribution in operation area is uniform because of the small differences of sprinklers discharge pressure. Loop type is superior to tree type in respect of total pressure and flow rate. Using the small diameter pipe, the labor and construction cost will be decreased in the end. Loop type sprinkler design is rarely laid out because design engineers don't know the method. This paper is intended to inform that the loop type is better than the tree type in performance and economic point of view. And also this paper intend to use the loop type easily and widely.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.1
• /
• pp.39-44
• /
• 2012

The new blind design of sunlighting has been suggested in this study. The material in this blind becomes transparent but the blind has the parabolic edge section having the perpendicular line on a side. The material of this blind is PolyMethly MethAcrylate(PMMA). In this parabolic edge section, the front side of the blind is designed perpendicular to the ground. But the back side is a little tilted to the front side. The rays of reflected sun at the front side can be easily reflected totally by the back side. If the inclination angle in this parabolic edge section at the back side is designed with $15^{\circ}$, it can transmit the rays of sun when the height of the sun is lower than $45^{\circ}$. But it can reflect the rays of sun when the height of the sun is upper than $45^{\circ}$. The suggested design of blind can be applied to the existing blind installation. Although the material in this blind becomes transparent, the rays of sun can be reflected totally at midday. There is also prospect outside of the blind because the material becomes transparent. Several inclination angles in the suggested design have been simulated for the various height of sun. Total reflections have been occurred by the suggested blind design at midday and it can be useful to shut out the sunlight.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.99-99
• /
• 2011

하천에서 위어 하류단의 세굴은 매우 중요한 현상이며 위어 형상에 따른 수리학적 흐름특성이 세굴거리 및 세굴심에도 영향을 미치므로, 적절한 하상보호공 설계를 위해 다양한 위어 하류단의 세굴 규모 및 세굴 형상을 산정하는 연구가 필요하다. 본 연구에서는 사다리꼴 래버린스 위어를 적용하여 일반적인 직선형 위어와 비교하였으며, 3차원 수치모의를 통해 하류단의 세굴 규모를 분석하였다. 현재 세굴 방지를 위하여 설치되는 위어 하류부 물받이 및 하상보호공의 설계 기준은 월류흐름에 의해 발생되는 하류부 세굴영향에 대한 고려가 미흡하며, 대부분 설계자료가 광정위어 및 예연 위어 형태만을 고려하고 있어 위어의 형상변화에 따른 고려 또한 부족한 실정이다. 따라서 하류부 세굴방지공의 안전하고 경제적인 설계를 위하여 위어의 형상 변화에 따른 위어 하류부 세굴 특성 분석에 대한 연구가 필요하다. 본 연구에서 적용한 래버린스(labyrinth) 위어는 수로 내에 설치된 횡방향 직선형 위어의 단면 형상을 변경하여 월류길이를 증가시킨 긴 마루(long crested) 위어 형태의 일종이다. 일반적으로 래버린스 위어는 월류량 증대, 수질개선 및 수심유지 효과가 필요한 수공구조물에 이용되어 하천에 적용될 경우, 관련 수공구조물의 수심 확보 측면에서 기여할 수 있는 구조물로 잘 알려져 있다. 수로폭과 유입유량을 알고 있을 경우 기존 연구자들에 의해 제시한 공식에 의해 직선형 위어의 하류단의 세굴거리와 세굴심을 산정할 수 있으며, 본 연구에서 제시한 세굴거리 비와 세굴심 비를 통해 래버린스 위어의 세굴거리 및 세굴심을 예측할 수 있었다. 분석결과 래버린스 위어의 하류단의 세굴거리는 직선형 위어에 비해 감소하고 세굴심은 증가하였으며, 총 마루길이 당 유입유량과 유입유량 조건에 따른 세굴거리 비 및 세굴심 비 변화를 통해 통수능 및 래버린스 위어의 마루길이 변화에 따른 세굴 영향범위를 조절할 수 있는 것으로 분석되었다. 추후 다양한 유량조건과 확폭비를 고려한 연구를 수행한다면 래버린스 위어의 마루길이에 따라 하상보호공 설계시 중요한 인자인 세굴거리와 세굴심을 조절할 수 있으며, 위어 형상에 따른 하류단 세굴 규모를 산정과 더불어 확장된 하상보호공 설계자료로 이용할 수 있을 것이다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.4
• /
• pp.793-798
• /
• 2016

In this work, the memory window characteristics of vertical nanowire device with asymmetric source and drain was analyzed using bipolar junction transistor mode for 1T-DRAM application. A gate-all-around (GAA) MOSFET with higher doping concentration in the drain region than in the source region was used. The shape of GAA MOSFET was a tapered vertical structure that the source area is larger than the drain area. From hysteresis curves using bipolar junction mode, the memory windows were 1.08V in the forward mode and 0.16V in the reverse mode, respectively. We observed that the latch-up point was larger in the forward mode than in the reverse mode by 0.34V. To confirm the measurement results, the device simulation has been performed and the simulation results were consistent in the measurement ones. We knew that the device structure with higher doping concentration in the drain region was desirable for the 1T-DRAM using bipolar junction mode.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.6
• /
• pp.698-705
• /
• 2010

A vehicle antenna for AM, FM, TDMB, GPS systems was designed and implemented. Omnidirectional AM antenna was designed by ferrite turn style antenna. For the FM and TDMB antenna, folded monopole antenna which helical is folded was applied. GPS antenna for the bandwidth achievement was designed by trapezoidal microstrip patch that has air substrate. Receiving signal strengths by the measurement were presented for the AM, FM and TDMB antenna. AM signal strength was -65.7 dBm, this strength is almost as same conventional pole antenna as -63.4 dBm. It can be replaced conventional pole or glass antenna by the studied antenna. Signal strengths for FM and TDMB were -55.66 and -43.50 dBm at center frequency, they are 5~10 dB higher than conventional antenna. Measurements of bandwidth and gain for the GPS antenna showed 135 MHz under VSWR 2 : 1 and 4.31 dBi, gains over GPS band were 3~5 dB higher than ceramic patch antenna.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.32 no.1
• /
• pp.74-82
• /
• 2014

The purposes of this study is to investigate spatial structure characteristics of earthen walled fortresses based on topography, which are locational and Plane morphology, Cross sections of earthworks. Target areas of this study are 37 earthen walled fortresses which are designated as cultural properties. This study is conducted with methodologies of literature review, field investigation, investigation on topography materials and relation analyses of topography&spatial structure. The results from study on spatial structure of earthen walled fortresses are as follows. First, Earthen walled fortresses on flat topography were adjacent to water systems like rivers or streams. Plane morphology showed regular shapes. The cross section morphology presented trapezoid the most with earthworks of which outer and inner walls were built. Second, More than 70% of earthen walled fortresses on hilly topography had water system within close range of approximately 1.5km. Plane morphology was mainly with more than 73% of irregular types. Cross sections of earthworks were of morphology with more than 86% of bordered type and another type leaning against existing topography like mountains. Third, 59% of earthen walled fortresses in mountain areas had water system within their close range, which indicated that they depended on external water system less than those with hilly topography. Plane morphology was mainly with more than 67% of irregular types. Cross sections of earthworks were of monoslope method with more than 94% of bordered type and another type leaning against mountains.

• The Korean Journal of Applied Statistics
• /
• v.22 no.1
• /
• pp.141-151
• /
• 2009

According to the type of microdata, the various methods have been in use for masking microdata. Multiplicative noise is the one of popular schemes for masking continuous variables. In this paper, we introduce the method of masking based on multiplicative noise and show some results of the application on the 2006 Householder Income and Expenditure Survey (HIES) data. To create the multiplicative noise factor, we used the triangular distribution. truncated triangular distribution, trapezoidal distribution, and double triangular distribution. Also, formulas for the domain estimation for the data masked by the multiplicative noise are developed.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.15 no.3
• /
• pp.167-175
• /
• 2003

In this study, reflection of regular waves over a train of submerged breakwaters is experimentally investigated. Wave reflection from various-shaped submerged breakwaters is examined by using laboratory experiment and eigenfunction expansion method. Shapes of submerged breakwaters are rectangular, triangular, trapezoidal and semi-circular. Laboratory measurements are compared with predicted coefficients obtained from the eigenfunction expansion method. Although measured coefficients are slightly smaller than predicted ones, the overall agreement is very good. The present study can provide a criterion for the proper choice of a shape of submerged breakwaters in practical situation.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.1
• /
• pp.88-95
• /
• 2004

Micro stepping method is adopted in order to eliminate effectively the resonant phenomena and to increase the positional resolution. Exist micro-step method by using Sinusoidal waveform, drive circuit is complex by using micro controller and ROM, it have fault on cost Increase. This paper proposed trapezoidal current wave form for simple control circuit and micro stepping method by using a low cost controller. This paper proposed method verify by using CPLD(EPM9320RC208-15) of low cost. This paper make experiment that comparison of exist method and proposed method. This paper obstruct a escape of motor by using high speed detect.