• 한국도로학회:학술대회논문집
• /
• 2002.10a
• /
• pp.89-92
• /
• 2002

The objective of this research is to evaluate engineering properties of recycled aggregates, slag as coarse & fine aggregate and waste foundry sand(WFS) as fine aggregate, in hot mix asphalt(HMA). In this research, soundness, gradation and particle analysis, abrasion, specific gravity and absorption test were carried out. The optimum asphalt binder content(OAC) for various HMA combinations of recycled aggregate was determined by Marshall Mix Design. The ranges determined is between 7.2% and 7.5%. Indirect tensile test, resilient modulus test, creep test were carried out for characterization of rutting behavior of various combination of HMA. Judging from the limited tests, the HMA with recycled aggregates is not as good rutting resistance as the HMA with common aggregates. After finishing the Wheel tracking test, the application or feasibility for the use of recycled aggregate as asphalt paving material will be determined.

• The Journal of Engineering Geology
• /
• v.26 no.4
• /
• pp.593-600
• /
• 2016

To understand the mechanical properties of rock masses and intact rock in Korea, data from 4,280 in situ and laboratory tests from 107 tunnels on general national roads were analyzed. The mechanical properties (unit weight, cohesion, friction angle, modulus of deformation, Young's modulus, Poisson's ratio, uniaxial compressive strength, tensile strength, coefficient of permeability, and specific gravity) were analyzed by rock types and strength of rock in each rock type. The results of analysis, the mean specific gravity was highest in gneiss. The coefficient of permeability and Poisson's ratio show the highest mean values in granite and metamorphic rock, respectively. In addition, the unit weight, cohesion and friction angle in sedimentary rock, modulus of deformation, Young's modulus, uniaxial compressive strength and tensile strength in volcanic rock have the highest mean values. The values for each mechanical property showed wide ranges by the heterogeneity and anisotropy of rock masses in spite of detailed analysis by rock type and classification of rocks according to the strength.

• Journal of the Korean Society for Railway
• /
• v.17 no.1
• /
• pp.43-51
• /
• 2014

In the earth structures of railways, large coarse granular materials are widely used as fill materials. However, experimental studies that consider the dynamic properties of these coarse granular materials have rarely been carried out in Korea due to the lack of a large scale test apparatus in this country. In this study, large scale cyclic triaxial tests were carried out for materials such as reinforced roadbed (subballast, graded crushed stone), transition zone gravel, and the upper subgrade of a railway. These specimens were prepared according to certain conditions (dry unit weight, grain size distribution, and so on) specified in the Korea railroad design standard. Based on these large triaxial test results, normalized shear modulus and damping ratio curves according to small strain level are suggested. A model and coefficients for each material are also proposed.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.1 s.68
• /
• pp.21-32
• /
• 2004

In this study, a continuous optimum design model with its application program for plane steel frame structures developed. In the model, the sequential unconstrained minimization technique (SUMT) transforming the nonlinear optimization problem with multidesign variables and constraints into an unconstrained minimization problem and the refined plastic hinge analysis method as one of the most effective second-order inelastic analysis methods for steel frame structures were implemented. The total weight of a steel frame structure was taken as the objective function, and the AISC-LRFD code requirements for the local and member buckling, flexural strength, shear strength, axial strength and size of the cross-sectional shapes of members were used for the derivation of constraint equations. To verify the appropriateness of the present model, the optimum designs of serveral plane steel frame structures subject to vertical and horizontal loads were conducted.

• Journal of Biosystems Engineering
• /
• v.9 no.1
• /
• pp.34-45
• /
• 1984

우리가 소비하는 식량의 확보는 단위 수량의 증대 뿐만 아니라, 생산이후 수확, 조제가공 및 건조 저장과정에서의 곡물 손실 방지 또는 감소로 인한 간접 증산으로도 이룩될 수 있는데, 현재 우리나라에서는 수확 이후의 곡물 손실량이 전체 생산량의 약 11%에 달하는 것으로 추정되고 있다(12). 여기서 식량의 중요 손실원으로 기계적 원인과 곡물 자체의 특성에 의한 두가지 요인을 고려할 수 있다. 따라서 쌀의 물리적 특성이 규명되면 각 과정에서 발생되는 기계적 손실을 더욱 줄일 수 있을 것이다. 이러한 중요성에도 불구하고 지금까지 우리나라에서는 벼의 물리적 특성에 관한 연구가 거의 없는 실정이다. 특히 우리나라에 많이 보급되고 있는 통일계 품종은 관행 품종에 비하여 물리적 특성이 크게 다르다고 인정되고 있다. 따라서 본 연구는 벼와 현미의 특성을 기계적 및 유동학적 측면에서 함수율 및 품종별로 규명하여, 농업기계의 설계 및 작동조건, 그리고, 조제가공의 기초적 자료로 제시하고자 하였다. 실험 결과를 요약하면 다음과 같다. 1. 준 정하중의 압축시험에서 함수율은 벼와 현미의 기계적 및 유동학적 특성에 큰 영향을 미쳤으며, 특히 높은 함수율에서는 점성적인 특성이, 낮은 함수율에서는 탄성적인 특성이 나타났다. 2. 벼와 현미의 함수율이 24-12% (습량기준)의 범위에 있을 때 현미의 항복점은 2.0-7.2kg, 벼의 항복점은 2.5-7.6kg을 나타냈으며, 전반적으로 현미보다 벼의 항복점이 0.5-1kg 더 높았다. 또한 함수율이 18%(습량기준) 이하에서는 일반계 품종이 통일계 품종보다 압축 강도가 더 높았으나 18% 이상의 높은 함수율에서는 더 낮게 나타났다. 그리고 낮은 함수율에서 현미의 항복점은 현미 두께 대 길이의 비의 증가에 따라 직선적으로 감소하였다. 3. 현미의 최대압축 강도는 함수율 24-12%(습량기준)의 범위에서 2.94-10.4kg을 나타냈으며, 14% 수준의 낮은 함수율에서는 현미의 최대 압축 강도는 5.66-11.4kg으로 품종간에 높은 유의성이 있었다. 따라서 벼와 현미의 크기가 최대 압축 강도에 큰 영향을 미친 것으로 사료된다. 4. 함수율 12-24%(습량기준)의 범위에서, 현미의 항복점에서 변형은 0.20-0.40mm를 나타냈으며, 함수율이 약 17%일 때 최소치를 보였다. 벼의 항복점에서 변형은 0.20-0.41mm 였으며 통일계 품종이 일반계 품종보다 변형이 더 많이 생겼다. 5. 함수율 24-12%(습량기준)의 범위에서, 일반계 품종의 레질리언스(resilience)는 $0.142-0.603kg{\cdot}mm$, 통일계 품종의 레질리언스는 $0.229-0.601kg{\cdot}mm$로 나타났다. 함수율이 19% 이하에서는 일반계 품종이 통일계 품종보다 더 높게 나타났으며 19% 이상에서는 반대 현상이 일어났다. 또한 14%의 낮은 함수율에서, 현미의 레질리언스는 현미 두께 대 길이의 비의 증가에 따라 감소하였다. 벼의 레질리언스는 함수율의 감소에 따라 증가했으며, 그 범위는 $0.285-0.850kg{\cdot}mm$이었다. 6. 현미의 터프니스(toughness)는 함수율 24-12%(습량기준)의 범위에서 $0.841-2.795kg{\cdot}mm$이었다. 또한 일반계 품종과 통일계 품종 사이에는 유의성이 없었으나. 품종간에는 높은 유의성이 있었다. 7. 현미의 탄성계수와 스티프니스(stiffness)는 함수율의 감소에 따라 직선적으로 증가하였다. 현미의 함수율이 24-12%(습량기준)의 범위에 있을 때 탄성계수는 $7-40kg/mm^2$, 스티프니스는 8-34kg/mm를 나타냈다.

• 한국지구물리탐사학회:학술대회논문집
• /
• 1999.08a
• /
• pp.48-64
• /
• 1999

For quantitative evaluation of geotechnical engineering properties such as rippability and diggability, clear interpretation on the subsurface velocity structures should be preceded by figuring out top soil, weathered and soft rock layers, shape of basement, fracture zones, geologic boundary and etc. from the seismic refraction data. It is very important to set up suitable field parameters, which are the configuration of profile and its length, spacings of geophones and sources and topographic conditions, for increasing field data quality Geophone spacing of 3 to 5m is recommended in the land slope area for house land development and 5 to 10m in the tunnel site. In refraction tomography technique, the number of source points should be more than a half of available channel number of instrument, which can make topographic effect ignorable. Compared with core logging data, it is shown that the velocity range of the soil is less than 700m/s, weathered rock 700${\~}$1,200m/s, soft rock 1,200${\~}$1,800m/s. And the upper limit of P-wave velocity for rippability is estimated 1,200 to 1,800m/s in land slope area of gneiss. In case of tunnel site, it is recommended in tunnel design and construction to consider that tunnel is in contact with soft rock layer where three lineaments intersecting each other are recognized from the results of the other survey.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.4
• /
• pp.503-509
• /
• 2019

The demand for smaller, faster, and multi-functional mobile devices in increasing at a rapidly increasing rate. In response to these trends, Stacked Chip Scale Package (SCSP) is used widely in the assembly industry. A film type adhesive called die attach film (DAF) is used widely for bonding chips in SCSP. The DAF requires high flowability at high die attachment temperatures for bonding chips on organic substrates, where the DAF needs to feel the gap depth, or for bonding the same sized dies, where the DAF needs to penetrate bonding wires. In this study, the mixture design of experiment (DOE) was performed for three raw materials to obtain the optimized DAF recipe for low elastic modulus at high temperature. Three components are acrylic polymer (SG-P3) and two solid epoxy resins (YD011 and YDCN500-1P) with different softening points. According to the DOE results, the elastic modulus at high temperature was influenced greatly by SG-P3. The elastic modulus at $100^{\circ}C$ decreased from 1.0 MPa to 0.2 MPa as the amount of SG-P3 was decreased by 20%. In contrast, the elastic modulus at room temperature was dominated by YD011, an epoxy with a higher softening point. The optimized DAF recipe showed approximately 98.4% pickup performance when a UV dicing tape was used. A DAF crack that occurred in curing was effectively suppressed through optimization of the cure accelerator amount and two-step cure schedule. The imizadole type accelerator showed better performance than the amine type accelerator.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.9 no.5 s.45
• /
• pp.53-61
• /
• 2005

In order to evaluate the limit earthquake resistance of multi-story steel frames influenced by the strength and stiffness ratios of members, a series inelastic response analysis were carried out. From the analysis results, the damage distribution rules of multi-story steel frames were proposed. Conclusions are summarized as follows; 1)As the stiffness ratios of beam and column becomes small, the damage concentrates on the lower end of columns of the first story. 2) Considering the strength and stiffness ratios of the beam and column with weak beam type mechanism, the equations predicting the damage distribution of multi-story steel flames were proposed. 3) Through the equation which was supposed in this study, it is speculated that the damage distribution of the rigid or semirigid beam collapse type multi-story steel structure building can be predicted.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.273-276
• /
• 2008

The use of FRP(Fiber Reinforced Polymer) bars to replace conventional steel bars in reinforcing concrete structures is currently encouraged by many structural engineers, especially for their noncorrosive properties. The partial inferiority of the bond and mechanical properties for FRP bars, however, leads to wider and deeper cracks compared with those of steel reinforced concrete structures. This paper presents experimental results of concrete beams reinforced with FRP bars tested under static loading conditions up to failure. The study focuses on the effects of the reinforcement ratio on the behavior of concrete beams at various stages during loading. The study also attempts to establish a theoretical basis for the development of simple and rational design procedures for concrete beams reinforced with FRP bars.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.7 no.3
• /
• pp.31-38
• /
• 2003

Lap splices were located in the plastic hinge region of most bridge piers that were constructed before the adoption of the seismic design provision of Korea Highway Design Specification on 1992. But sudden brittle failure of lap splices may occur under inelastic cyclic loading. The purpose of this study is to analytically predict nonlinear hysteretic behavior and ductility capacity of reinforced concrete bridge piers with lap splices under cyclic loading. For this purpose, a nonlinear analysis program, RCAHEST(Reinforced Concrete Analysis in Higher Evaluation System Technology) is used. Lap spliced bar element is developed to predict behaviors of lap spliced bar. Maximum bar stress and slip of lap spliced bar is also considered, The proposed numerical method for seismic performance evaluation of reinforced concrete bridge piers with lap splices is verified by comparison with reliable experimental results.