• Journal of the KSME
• /
• v.54 no.3
• /
• pp.42-46
• /
• 2014

전통적인 개복수술에 비해서 경감된 수술 후 회복기간 등 여러 가지 장점이 있는 최소절개수술은 수술자들에게는 훨씬 복잡하고 배우기 어려운 기법으로 알려져 있다. 이 글은 최소절개수술의 기법을 향상시키는 데 도움이 되는 다양한 계측 및 제어 기술을 검토하고 새로운 디바이스를 소개하는 데 초점을 둔다.

• The korean journal of orthodontics
• /
• v.34 no.5 s.106
• /
• pp.448-457
• /
• 2004

As computer Programs for cephalometric analysis were developed in diagnosis & treatment planning, digital imaging of film-based cephalograms came to be needed. When a digital camera is used, a problem encountered the image distortion produced according to the focal length, which causes errors in indentifying landmarks. In addition, changes in the image size and compression ratio will inevitably produce a low quality image, causing errors in identifying landmarks. Hence. we have found the focal length producing the least image distortion when digital imaging the film-based cephalograms and the minimal digital camera setting which helps to identify the correct landmarks using the COOLPIX4500 digital camera (Nikon, Japan). The results were as follows The image distortion was minimized at a focal length of 16.4mm (79.4mm when converted into a 35mm film camera) when digital imaging the film-based cephalograms. When wide imaging, with a focal length of under IS.4mm, barrel distortion was found and when tole imaging. with a focal length of over 15.4mm pincushion distortion was found. The minimal digital camera setting was $2272{\times}1704$ pixel at normal (1/8) compression from which we can identify the correct landmarks at the same level as tracing the film-based cephalograms manually. As a result. when digital imaging the film-based cephalograms, using a COOLPIX4500 digital camera (Nikon, Japan), the focal length should be 16.4mm the pixel image size over $2272{\times}1704$, and the compression ratio over normal (1/8).

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.1
• /
• pp.129-137
• /
• 2000

In this paper, a new method of noncontact measurement has been developed for a 3 dimensional topography in semiconductor wafer, implementing a new optical probe based on the precision defocus measurement. The developed technique consists of the new optical probe, precision stages, and the measurement/control system. The basic principle of the technique is to use the reflected slit beam from the specimen surface, and to measure the deviation of the specimen surface. The defocusing distance can be measured by the reflected slit beam, where the defocused image is measured by the proposed optical probe, giving very high resolution. The distance measuring formula has been proposed for the developed probe, using the laws of geometric optics. The precision calibration technique has been applied, giving about 10 nanometer resolution and 72 nanometer of four sigma uncertainty. In order to quantitize the micro pattern in the specimen surface, some efficient analysis algorithms have been developed to analyse the 3D topography pattern and some parameters of the surface. The developed system has been successfully applied to measure the wafer surface, demonstrating the line scanning feature and excellent 3 dimensional measurement capability.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.1 no.2
• /
• pp.27-31
• /
• 2000

Thermal imaging system is implemented for the measurement and the analysis of the thermal distribution of the target objects. The main Part of the system is thermal camera in which a focal plane array typed sensor is introduced The sensor detects mid-range infrared spectrum or target objects and then it output generic video signal which should be processed to form a thermal image frame. A digital signal processor(DSP) in the system inputs analog to digital converted data. performs algorithms to improve the thermal images and then outputs the corrected frame data to frame buffers for NTSC encoding and for digital outputs.. To enhance the quality of the thermal images, two point correction method is applied. Figures indicate that the corrected thermal images are much improved.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.25 no.2
• /
• pp.74-80
• /
• 2005

A new dimension measuring method for the measurement of diameter of an object has been developed using laser triangulation. The 3D data of an object was calculated from the 2 dimensional image information obtained by the laser stripe using the laser triangulation. The system that use existing theory can measure the diameter of hole not only in a normal plane but also ill an incline plane. However, in the existing theory, since the lens with fixed feral length was used, the area of measurement was fixed. The simplest way to solve this problem is to change distance between a CCD camera and object. Other way is to use a zoom lens having variable focal length. In this paper, the zoom lens with variable focal length was used. Therefore, we ran experiment with magnification that is optimized according to size of object using zoom lens with variable focal length.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.422-422
• /
• 2015

수문학적 모델링은 수자원계획에 있어 가장 핵심적인 도구 중에 하나이다. 강우-유출모형의 매개변수 추정시 장기간의 자료를 활용하는데 초점이 맞추어져 있으며, 일반적으로 5년 이상의 자료를 활용하여 매개변수를 추정하는 경년변동(inter-annual variability) 매개변수 추정 방법이 추천되고 있다. 수문학적 변동성 측면에서 볼 때 강우, 온도, 유역의 조건 등의 연내변동성(intra-annual variability)이 경년보다 크게 나타나고 있으나, 이러한 특성을 고려한 수문모형의 매개변수 추정은 이루어지고 있지 않다. 이러한 점에서 연내변동성으로 기인하는 비정상성을 고려한 매개변수 추정 방법의 도입이 필요할 것으로 판단되며, 본 연구에서는 계측유역을 대상으로 다양한 시간규모에서 매개변수 추정을 수행하고 최적의 시간규모를 도출하고자 한다. 이를 위해서 DDS(dynamically dimensioned search) 알고리즘을 도입하여 최적화를 수행하였으며, 다양한 시간 규모에서 모형의 적합특성을 평가하였다. 교차검증을 통하여 매개변수의 통계적 유의성을 확보하였으며, 전통적인 매개변수 추정 절차와 비교 검토를 수행하였다.

• Journal of the KSME
• /
• v.25 no.4
• /
• pp.320-326
• /
• 1985

지난 10여년간의 연소분야에 대한 연구는 크게 세가지 방향에서 괄목할 만한 발전을 이루어 왔다. 그 첫째는 대용량 컴퓨터의 개발에 따른 수치해석능력의 신장을 들 수 있고, 둘째는 실 험에서 레이저를 이용한 비접촉 계측방법의 발달을 들 수 있다. 또한 이론적 관점에서는 1974 년이래 유체역학에서 프란틀의 경계층 이론에 비견될 수 있는 접합점근방법(matched asymptotic technique)를 이용하여 예혼합 화염의 전파속도, 확산화염의 구조 및 점화/소화현상, 열폭발문제, 화염의 안정성 등에 관한 엄격한 해석이 가능하게 되었다. 이로서, 종래의 현상적, 물리적 설 명으로 이해될 수 없었던 분야를 해석할 수 있었다. 이에 따라 본 강좌에서는 연소분야의 이 론적 연구에 초점을 맞추어 접합점근방법의 기초개념 및 해석방법을 소개하고자 한다. 이를 위해 2장에서 확산 화염과 예혼합 화염의 특성을 설명하고, 3장에서 화염면 극한의 해석, 4장에서 확산 화염의 구조해석을 통한 점화/소화현상 및 5장에서 예혼합 화염에의 응용 등을 소개한다.

• Journal of IKEEE
• /
• v.26 no.2
• /
• pp.219-225
• /
• 2022

The textile industry in Korea, the dyeing sector is an energy-intensive sector and has low per-unit productivity due to its labor-intensive nature. If the defective rate of dyed fabrics is high, additional costs are incurred due to an increase in production cost due to re-dyeing. Therefore, the goal of the dyeing factory was to minimize the defect rate rather than to save energy. It was difficult to check the dyeing state of the fabric in real time due to the risk of accidents due to burns or pressure when dyeing in a high-temperature and high-pressure environment. In this paper, a complex sensor that can measure the exhaustion rate of dye solution in the dyeing machine using turbidity, pH, and conductivity sensors was proposed, and the experimental method and experimental results were analyzed.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.4
• /
• pp.301-308
• /
• 2016

In this study, a novel method referred as non-marker vision-based displacement measuring system(NVDMS) was introduced in order to measure the displacement of structure. There are two distinct differences between proposed NVDMS and existing vision-based displacement measuring system(VDMS). First, the NVDMS extracts the pixel coordinates of the structure using a feature point not a marker. Second, in the NVDMS, the scaling factor in order to convert the coordinates of a feature points from pixel value to physical value can be calculated by using the external conditions between the camera and the structure, which are distance, angle, and focal length, while the scaling factor for VDMS can be calculated by using the geometry of marker. The free vibration test using the three-stories scale model was conducted in order to analyze the reliability of the displacement data obtained from the NVDMS by comparing the reference data obtained from laser displacement sensor(LDS), and the measurement of dynamic characteristics was proceed using the displacement data. The NVDMS can accurately measure the dynamic displacement of the structure without the marker, and the high reliability of the dynamic characteristics obtained from the NVDMS are secured.

• The korean journal of orthodontics
• /
• v.30 no.1 s.78
• /
• pp.53-66
• /
• 2000

This study was performed to find out the effect of projection errors on cephalometric linear and angular measurements according to head rotation during taking lateral cephalometric radiographs. Seventeen skulls with permanent dentition and no gross asymmetry were obtained from the Department of Anatomy, Medical School, Chosun University. Total 527 x-ray films were taken with $1^{\circ}$ interval from the reference position($0^{\circ}$) to ${\pm}15^{\circ}$ around the vertical axis (Z axis) which is perpendicular to the midpoint of the line connecting the center of two ear rods in submento-vertex direction. Statistical analysis was performed by paired t-test if there were statistically significant differences between the mean of the reference position($0^{\circ}$) and that of each rotation angle. The following results were obtained. 1. The projection errors of angular measurements were smaller than those of linear measurements. 2. The projection errors of angular measurements including midline landmarks were smaller than those including bilateral landmarks. 3. The horizontal linear measurements were gradually decreased when the stroll was rotated toward the film, but slightly increased and then decreased when the skull was rotated toward the focal spot. However, the changes were smaller in focal direction. 4. The projection errors of horizontal linear measurements were larger than those of vertical linear measurements. 5. The projection errors of vertical linear measurements were increased with increased distance from the rotation axis to vertical measurements. It is concluded that the use of angular measurements rather than linear measurements is recommended to minimize the projection errors.