• 대한기계학회논문집
• /
• 제15권1호
• /
• pp.139-144
• /
• 1991

본 연구에서는 절삭가공시 생성되는 칩의 형상해석의 일환으로 2차원 절삭시 칩은 절삭날에 수직한 방향으로 공구경사면을 흘러간다는 기본적인 전제조건과 Kluft 등의 칩흐름각 예측에 대한 제안중 노으즈반경(nose radius) 및 기울임각의 영향을 중 첩시키고, 또한 절삭날에 연하여 미변형 칩두께(undeformed chip thickness)가 달라지 는 경우 칩흐름의 세기는 이에 비례한다는 Baart등의 가정을 도입하여 칩흐름각에 대 한 새로운 해석을 시도하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.1059-1062
• /
• 1995

In cutting system, relative displacement between rool and workpiece is very important. Even though there have been so many works for modeling cutting process of end-milling, most of them have considered only one displacement of either tool or workpiece instead of both. In this paper, the relative displacement between tool and workpiece is considered for modeling cutting process of end-milling using simple experimental modal analysis and cutting force simulation program is developed. In cutting force model, instantaneous uncut chip thickness model is used and Runge-Kutta method is used for the simulation of time varying cutting system.

• 한국공작기계학회논문집
• /
• 제15권2호
• /
• pp.73-80
• /
• 2006

This paper describes a analysis on the chip thickness model required for cutting force simulation in ball-end milling. In milling, cutting forces are obtained by multiplying chip area to specific cutting forces in each cutting instance. Specific cutting forces are one of the important factors for cutting force predication and have unique value according to workpiece materials. Chip area in two dimensional cutting is simply calculated using depth of cut and feed, but not simply obtained in three dimensional cutting such as milling due to complex cutting mechanics. In ball-end milling, machining is almost performed in the ball part of the cutter and tool radius is varied along contact point of the cutter and workpiece. In result, the cutting speed and the effective helix angle are changed according to length from the tool tip. In this study, for chip thickness model analysis, tool and chip geometry are analyzed and then the definition of chip thickness and estimation method are described. The resulted of analysis are verified by compared with geometrical simulation and other research. The proposed chip thickness model is more precise.

• 한국기계가공학회지
• /
• 제11권4호
• /
• pp.7-12
• /
• 2012

The cutting force for peripheral end-milling considering run-out property was estimated and its result was compared with that of measured one. An experimental coefficient modelling was used for the formulation of theoretical end-milling force by considering the specific cutting force coefficient. Also, the specific cutting force, that is the multiplication of specific cutting force coefficient and uncut chip thickness, was used for the prediction of end-milling force. The end-milling force mechanics with run-out was presented for the estimation of theoretical force in peripheral end-milling by considering the geometric shape of the workpiece part. As a result, the estimated end-milling force shows a good consistency with the measured one. And it can be used for the prediction of force history in end-milling with run-out which incurs different start and exit immersion angle in entering and exiting condition.

• 한국정밀공학회지
• /
• 제18권7호
• /
• pp.143-148
• /
• 2001

In this study, a mechanistic model of cutting force components in up and down end milling process is presented. Using this cutting force model of 4-tooth endmills with various helix angles, cutting force variation of inconel 718 has been predicted. Predicted values of cutting force components are coincide well with the measured ones. As helix angle increases, overlapping effects of the active cutting edges increase. In up endmilling the magnitudes of radial and feed cutting force componts FX and FY are lowest when the helix angle is $40\{\circ}$, but in down endmilling the magnitudes of these values increase slightly as helix angle becomes large.

• Composites Research
• /
• 제24권4호
• /
• pp.23-28
• /
• 2011

최근 항공용 재료 산업 분야에서 널리 사용되고 있는 CFRP의 활용이 증가되고 있다. 하지만, CFRP와 같은 복합재료 부품의 결합 시에 단점이 있다. 복합재료를 이용한 다양한 구조를 제조하기 위해선 많은 홀 가공이 필요하다. 일반적으로 CFRP 홀 가공시 내구성이 매우 강한 polycrystalline crystalline diamond (PCD) 드릴을 사용한다. 하지만, 단가가 비싸고 가공 속도가 느리기 때문에 내구성은 PCD 드릴에 비해 약하나 드릴 형상 변화를 통해 가공 속도를 조절 할 수 있고, 비교적 가격이 저렴한 chemical vapor deposition (CVD) 다이아몬드 코팅 드릴의 사용량이 증가 되고 있다. 본 연구에서는. PCD 드릴과 CVD 다이아몬드 코팅 드릴의 홀 가공성을 비교 평가하였다. 먼저, 홀 가공 조건 식 (날당 이송량, 절삭 속도)을 이용하여 CFRP 홀 가공성을 평가했으며, CFRP 가공 시 드릴링 과정에서 발생하는 시편 내부의 열적 손상 정도를 비교했다. 열화상 카메라 촬영한 홀 가공 시 발생되는 온도를 이용한 경험식을 만들어 두 드릴의 발열 정도에 따른 홀 가공성을 비교 평가하였다. 또한, 홀 가공 시 발생하는 칩(chip) 배출 여부에 따른 홀 내부의 상태를 평가하여 CVD 다이아몬드 코팅 드릴과 PCD 드릴의 CFRP 홀 가공성을 비교했다. 전반적으로 PCD 드릴의 홀 가공성이 CVD 다이아몬드 드릴에 비해 우수한 성능을 나타냈지만, 홀 생성 속도는 CVD 다이아몬드 드릴이 PCD 드릴에 비해 빠른 결과를 나타냈다.