• Clean Technology
• /
• v.26 no.3
• /
• pp.211-220
• /
• 2020

This experimental study investigates the design parameters to achieve ultra low NOx combustion of coal using a 80 kW capacity single-burner furnace. The influence of key design parameters such as SN, overall and burner-zone equivalence ratios, primary/secondary air ratio, overfire air (OFA) ratio were tested for a total of 81 cases. The results showed that weak swirl intensity of the burner leads to higher NOx emission whereas strong swirl intensity accompanies increased CO concentration desipte lower NOx emission. Therefore, finding an appropirate swirl intensity is essential for the burner design. Larger flow rate of secondary air increased NOx emission, whereas smaller flow rate stretches the flame and increased CO emission. The lowest NOx emission of 82 ppm (6% O₂) was achieved at the optimal condition of the present burner deisgn. It is expected to furrther lower the NOx emission by introducing splitting the burner secondary air into three or four streams.

• The Journal of Korean Academy of Prosthodontics
• /
• v.56 no.1
• /
• pp.40-49
• /
• 2018

It is reported that the causes of unaesthetic proportion of anterior teeth vary widely. Especially, when the unaesthetic tooth proportion of the mandibular incisors arises due to the wear of the anterior teeth accompanied by the compensation of the alveolar bone, it may cause serious functional and aesthetic problems. In such case, it should be considered that the evaluation of vertical dimension and tooth proportion as well as smile line, soft tissue and hard tissue morphology. And, increase of vertical dimension or clinical crown lengthening followed by prosthodontic restorations is needed to improve the interdental mesial/distal, width/length ratio considering the anterior guidance. This case report demonstrates functional and aesthetic improvements through systematic diagnosis and treatment procedures in a 48-year-old male patient with unaesthetic anterior teeth proportion because of tooth wear accompanied by the compensation of alveolar bone and defect of several central incisors due to chronic periodontitis.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.3
• /
• pp.654-666
• /
• 2018

This study was determined the effects of dietary omega-6 and 3 fatty acid ratios (n-6/n-3, 0, 4:1, 15:1, 30:1) on lipid metabolism in obese model animal rats. Blood triacylglycerol, total cholesterol, LDL-C, glucose, ALT, AST, insulin, and leptin concentrations in n-6/n-3 group were decreased by 22.21, 20.60, 52.96, 15.71, 11.97, 9.13, 37.57, 45.98%, respectively, while HDL-C and phospholipid concentrations were increased by 28.38, 80.39% respectively, compared with control group, as especially in 4:1 group showed the greatest effect. SREPB-$1{\alpha}$ and SREPB-2 mRNA in liver tissues were down-regulated in n-6/n-3 group, but LPL-mRNA of PPARs in adipose tissue was up-regulated compared with control group. The adipocyte size in liver tissues was decreased in the order of n-6/n-3 ratio of 30:1, control, 15:1 groups, and the adipocyte size in adipose tissues was decreased in the order of n-6/n-3 ratio of control, 30:1, 15:1, 4:1 groups.

• The Journal of Korean Academy of Prosthodontics
• /
• v.53 no.3
• /
• pp.262-275
• /
• 2015

The treatment of areas demanding esthetic requirements, such as maxillary anterior teeth, should take into account the achievement of a healthy, harmonious to the surrounding tissue, and an attractive smile line. In this case report, smile line, soft tissue and hard tissue morphology, and the anatomy and proportion of the tooth, must be considered. In patients with unesthetic maxillary anterior ratio due to inadequate gingival contour and diastema caused by peg lateralis, it would be challenging to achieve an esthetic restoration by orthodontic treatment alone. In such case, after orthodontic treatment, dento-gingivo-facial compositional diagnosis and analysis, followed by gingivectomy and prosthodontic restoration is needed to improve the interdental mesial/distal, width/length ratio to achieve a satisfactory esthetic result. In addition, when improving the tooth proportion of peg lateralis by prosthodontic treatment, Porcelain laminate veneer (PLV), which results in less tooth structure loss, reproduction of similar shade to that of the proximal tooth and high transparency, is recommended. This case report demonstrates esthetic improvements by prosthodontic restoration through systematic diagnosis and treatment procedure in patients with unesthetic maxillary anterior proportion after orthodontic treatment due to peg lateralis by means of two female patients aged twenty years old.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.61 no.1
• /
• pp.1-8
• /
• 2016

The objective of this study was to evaluate quality properties, including amylopectin content, and texture analysis of brown rice and germinated brown rice cultivars in Korea for rice processing products. The amylopectin short chain content of germinated brown rice was significantly higher than that of brown rice. Texture analysis test showed that germinated brown rice Jinbo had the lowest hardness and toughness as well as and highest stickiness and adhesiveness. The correlation between degree of polymerization of amylopectin and texture analysis was also evaluated. In particular, germinated brown rice, short-chain amylopectin showed a negative correlation with hardness and toughness, whereas long-chain amylopectin showed a positive correlation with hardness, toughness, and adhesiveness. These results indicate that there is a relationship between degree of polymerization and texture analysis.

• Food Science and Preservation
• /
• v.14 no.1
• /
• pp.30-34
• /
• 2007

This study investigated the effects of microcapsule wall materials and mixing ratios on the characteristics of microcapsules containing squid liver oil Emulsion stability was increased as Na-caseinate levels lose. Changes in mixing ratios of Na-caseinate and cyclodextrin caused micioencapsulation efficiencies to rise, fall, and then rise again. The particle size aid moisture contort of microencapsulated powders were not affected by the mixing ratios of wall materials. As the cyclodextrin content rose, water uptake was increased. The polyunsaturated fatty acid composition was shown to be higher then 50% in all powders, and the ratio of polyunsaturated fatty acid composition to saturated fatty acid composition was. 2.11 when the Na-caseinate and cyclodextrin mixing ratio was 4:6.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.109-112
• /
• 2008

It has better seismic performance and construction performance in precast column than in conventional RC column. In this research, seismic performances of precast column are analyzed by OpenSEES. Main variables of analysis are concrete strength, jacking ratio of tendon, amount of tendon and size of segment. As the amount of tendon and jacking ratio are increased, the flexural strength is also increased. And there is very little effect as it varies concrete strength and size of segment. But high initial jacking ratio leads to early yielding of tendon. And it is considered that a size of segment is related on construction problem. And also, strain in core concrete is less than ultimate strain. Consequently, it is considered that the amount of transverse steel will be reduced.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.39 no.3
• /
• pp.256-261
• /
• 1994

To investigate the effects of topping method on the yield and major agronomic traits of three varieties differed in plant type of Hibiscus manihot the experiments were carried out Mokpo Branch Station of Crop Experiment Station, in 1993. Fresh weight of root, dry weight of culm, dry weight of capsule and dry matter ratio on root were highest in the long culmed variety, and at the plots with topping of growing point in main culm and branches(Treatment No.3). Considering from the above results, optimum topping method seemed to be topping of growing point in main culm and branches in the long culmed variety.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.1
• /
• pp.67-74
• /
• 2012

A numerical analysis was carried out to estimate the effect of the gap size ratio on the performance of condensers under noncondensable gas ventilation using the porous medium approach (PMA). In the PMA, the details of the tube bundle in the condenser are considered to be those of a porous medium, and the flow resistance term is added in the momentum equation. Three-dimensional analysis of the condensation for a McAllister condenser was conducted with the PMA using Fluent and user-defined functions (UDFs). The gap size effect on the condensation was negligible under pure steam conditions. However, the gap size effect was dominant in condensation with noncondensable gas and external venting. As the gap size decreased, the condensation rate increased for noncondensable gas in an external venting system.

• Journal of the Korean Geotechnical Society
• /
• v.37 no.7
• /
• pp.35-42
• /
• 2021

An experimental study was carried out on kaolinite-sand mixtures with various proportions of kaolinite content. To investigate physical behaviour of mixtures, index properties and compaction test results were analysed in various aspects. Moreover, to clearly see the interaction between kaolinite and sand particles, the observational analysis through microscopic image analysis device was conducted. The test results showed that an increase in the amount of kaolinite could create a strong bonding structure which resulted in higher specific surface available for activities of kaolinite particles. Also, an increase in the amount of the kaolinite resulted in an increase in the percentage of water sorption. Then it could accelerate the occupation rate of water which tended to take up the space that would have been occupied by solid particles, and accordingly, resulted in the decreased maximum dry unit weight and increased initial void ratio. Based on the microscopic image analysis, the samples were individually classified into three types of mixture such as sand dominant, intermediate fine content, and fine dominant. In addition, the fine and coarse grains seem to interact well in the mixtures with the fine content ranging from 25 to 40%.