• Magazine of the Korea Concrete Institute
• /
• v.10 no.4
• /
• pp.171-182
• /
• 1998

Vibration-controlled concrete has been developed by using various concrete mixtures, such as latex, rubber powders, plastic resins and polystyrene(styrofoam). As part of the recycling research of obsolete aged tires and plastic materials, various vibration-reducing mixtures are used for 10 concrete panels having above 200 kg/cm$^2$ in uniaxial compressive strength. Plywood box with sand uniformly saturated by the raining device has been used for the analysis of the impact wave, of which data have been transfered by the FFT technique to comparatively investigate damping ratios of 10 concrete panels.According to wave propagation analysis on vibration-controlled concrete for this research, it can be concluded that Latex concrete has relatively larger damping ratios than those for noncontrolled normal concrete in a similar compressive strength

• Proceedings of the Korean Society of Disaster Information Conference
• /
• 2017.11a
• /
• pp.257-259
• /
• 2017

최근에 국내에서 입법된 "지하안전관리에 관한 특별법"의 지하안전영향평가 등에서 지하매설물 및 굴착공사 관리의 중요성을 강조하고 있지만, 아직까지는 지하를 개발함에 있어 지반의 안전과 관련된 사항은 미흡한 실정으로 도심지 지반침하( Sinkhole) 현상이 매년 증가하고 있다. 그리고 지반침하(Sinkhole)는 발생이 될 경우 인명피해는 물론 도로나 주변 건물들에 막대한 피해를 줄 수 있는 소지가 충분한 대상으로 사료됨에도 불구하고 이러한 현상을 건설현장에서 심각하게 받아들이는 분위기는 어느 곳에서도 감지되지 않는다. 다만 정부부처나 공공기관에서 국회차원의 지대한 관심에 부응하여 이에 대해 광범위한 연구와 조사에 막대한 예산을 투입하여 다방면에서 진행되고 있는 것으로 파악되고 있다. 또한 이러한 연구결과의 자료를 근거로 하여 지반침하 사고의 주요 원인을 조사해본 결과 상하수도관 손상과 무리한 인접굴착공사 및 대부분의 대형건축공사 현장에 채택되고 있는 부력방지 대책의 일환인 영구배수공법의 무분별한 적용을 들 수 있었다. 이러한 상황에서 그 중 비용과 난이도를 고려현장에서 용이하게 저감할 수 있는 방법인 영구배수공법을 선정하여 영구배수공법의 이론적 고찰과 공학적 타당성(구조체 부상방지 안전성 검토기준)을 연구하여 무분별한 영구배수공법 적용으로 지반침하(Sinkhole)가 발생하는 것을 막아 인명피해와 도로나 구조물의 안전성을 확보하고 나아가 영구배수공법 적용으로 항구적 발생하는 천문학적인 유지관리비의 절감이 목적이다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2018.05a
• /
• pp.19-19
• /
• 2018

최근 경주, 울산, 포항 등 경상도 지역에서 잇달아 발생한 대규모 지진으로 인해 사회기반시설물의 내진 안전성이 이슈가 되고 있다. 지진 안전 국가라고 여겨지던 우리나라는 상대적으로 지진에 대한 대비가 매우 부족한 실정이며, 자칫 대규모 피해로 이어질 우려가 있다. 특히 상수관망의 경우, 지중에 매설되어 있는 특성상 지진에 취약하고, 그 피해를 발견하기 어려워 장기적인 피해가 불가피하다. 상수관로의 지진피해는 누수와 파손으로 구분할 수 있으며, 파손관의 경우 용수공급능력을 크게 저하시키기 때문에 신속한 복구가 요구된다. 파손관의 복구는 부근에 위치한 차단밸브를 닫아 피해관로의 통수를 차단한 후에 복구 작업을 진행하는 것이 일반적이다. 이때, 차단밸브의 위치에 따라 단수구역이 광범위하게 발생할 수 있어 시스템 전반의 용수공급능력 저하로 이어질 가능성이 있다. 본 연구에서는 지진 발생 후 피해관로의 효율적인 복구전략 마련을 위한 상수관망 지진피해 복구 시뮬레이션 모형을 개발하였다. 개발 모형은 피해복구에 따른 상수관망 시스템의 용수공급능력을 정량적으로 산정할 수 있으며, 지진 발생과 같은 비정상 상황의 시스템 용수공급능력을 수리학적으로 정확하게 해석하기 위해 압력기반의 해석(Pressure-driven analysis, PDA)을 적용하였다. 또한, 피해관로의 복구 시, 차단밸브에 의해 발생되는 단수구역을 탐색한 후, 수리해석 모의에 적용함으로써 현실적인 용수공급 상황을 모의할 수 있도록 하였다. 본 연구에서는 개발모형을 활용하여 차단밸브의 위치 및 개수가 단수구역의 범위 및 지진복구에 미치는 영향을 정량적으로 비교 분석하였으며, 이를 통해 효율적인 지진피해 복구 전략을 제시하였다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 1999.05a
• /
• pp.254-260
• /
• 1999

Meteor Burst Communication can provide effective and economical means of communication where long distance VHF NLOS data transmission is needed; often ranges more than 1000 km. It has been, however, so far considered unsuitable for short distance application because of phenomenal decrease in burst durations, which leads to decreation of total duty rate of the system. This paper extensively analyzes characteristics of shot distance MB(Meteor Burst) path and shows the low duty rate may be improved by increasing burst rate through adapting antenna beam width to cover entire hot-spot region in the space and, by compensating effective burst length through cutting down man-made noises introduced by antenna. Based on the analysis, we are developed a small-opening-cavity antenna, especially designed for short distance MB path. In operation, the antenna is to be buried under ground surface so as to improve directivity and reduces noise introduction. The antenna exhibits power gain of 3 dB with 90 degree beam width and thus enables to illuminate entire hot-spot regions with the elevation angle of 8-90 degree which is the case of transmission less than 100 km. Directivity horizontal to earth surface is suppressed to minimum which enables to cut man-made noises from near-by sources down to more than 3 dB from the level reported with conventional 4 element Yagi. A series of experiments performed on 100 km MB paths have conformed that, with the antenna installed at receiving site, the burst rate and duration time have been noticed to increase by 10 and 20 percent respectively from the values obtained by conventional 4-element Yagi antenna under same testing condition.

• Elastomers and Composites
• /
• v.46 no.4
• /
• pp.335-342
• /
• 2011

The virgin and recycled polyethylene composites with various ratio of fly ash were manufactured by using a fully intermeshing co-rotating twin screw extruder for the reuse of fly ash from power plant and post-consumed polyethylene. Fly ash were blended with virgin HDPE and recycled polyethylene at the weight fraction of 0 to 40 wt.%. Mechanical properties such as yield strength, abrasion resistance, and slow crack resistance were measured with ISO and ASTM standards. The experimental results for the various composites showed that the elongation at break and the yield stress of the composites decreased with increasing fly ash contents. Generally, the abrasion resistance of PEs decreased with increasing sandpaper grits but the abrasion resistance of the composites increased with fly ash content at finer abrasive surface. The slow crack growth resistance of virgin HDPE, recycled JRPE and the JRPE composite showed higher slow crack growth resistance up to 50% of load at notch depth of 20% and 30%, but KRPE and the KRPE composite showed much lower resistance than virgin HDPE, JRPE and the JRPE composite. Time to break, measured with NCLS test method, of all PEs and the composites satisfies the regulation of Korean Industrial Specification for sewer pipe and support application.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.6
• /
• pp.788-801
• /
• 1998

Meteor Burst Communication can provide effective and economical means of communication where long distance VHF NLOS data transmission is needed ; often ranges more than 1000 km. It has been, however, so far considered unsuitable for short distance application because of phenomenal decrease in burst durations, which leads to decreation of total duty rate of the system. This paper extensively analyzes characteristics of shot distance MB(Meteor Burst) path and shows the low duty rate may be improved by increasing burst rate through adapting antennal beam width to cover entire hot-spot region in the space and, by compensating effective burst length throughcutting down man-made noises introduced by antennal. Based on the analysis, we are developed a small-opening-cavity antennal, especially designed for short distance MB path. In operation, the antenna is to be buried under ground surface so as to improve directivity and reduces noise introduction. The antennal exhibits power gain of 3 dB with 90 degree beam width and thus enables to illuminate entire hot-spot regions with the elevation angle of 8-90 degree which is the case of transmission less than 100 km. Directivity horizontal to earth surface is suppressed to minimum which enables to cut man-made noises from near-by sources down to more than 3 dB from the level reported with conventional 4 element Yagi. A series of experiments performed on 100km MB paths have conformed that, with the antenna installed at receiving site, the burst rate and duration time have been noticed to increase by 10 and 20 percent respectively from the values obtained by conventional 4-element Yagi antennal under same testing condition.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.9
• /
• pp.167-176
• /
• 2004

Underground structures will be affected by the additional surcharge loads such as traffic load et al. Terzaghi (1956) suggested the equation on the influences of surcharge loads in vertically backfilled spaces. In field, the shapes of backfill spaces are not always formed vertically. Then the Terzagi (1956) equation is not suitable to use because of boundary condition. This study suggests equation to calculate the stress in backfilled space caused by surcharge loads when the backfilled space is sloped symmetrically. The suggested equation is verified by carbon box test and numerical analysis. The experimental results show good agreement with the suggested equation but the numerical analysis result shows a little disagreement. The differences are estimated to be caused by the fact that ground made by carbon rod has become more dense and internal frction and wall friction has increased itself as surcharge load is added but that this increase can not be considered in the numerical analysis. The suggested equation shows good agreement with Terzaghi (1956) equation in case of sloped backfill ground. According to the results, it is considered that the suggested equation can be applied not only to sloped space but also to vertical space. Further investigation using full scale experiment is needed.

• International Journal of Highway Engineering
• /
• v.12 no.3
• /
• pp.27-35
• /
• 2010

Asphalt Plug Joint(APJ) is an buried expansion joint that enabling the smooth connection of expansion gap and road pavement by filling the gap with bituminous mixture of 20% bitumen and 80% aggregate by weight, so it secures evenness and expansion or contraction using the material's properties. Although APJ is designed to have a 6-7 year lifecycle, there are some cases where it is damaged within the first six months. This early damage cause traffic congestion due to frequent repair works, and social cost exceeding the installation cost of the joint. So, in this research, we have developed a new system of Buried Folding Lattice Joint(BFLJ) which can overcome the disadvantages of APJ, and have analyzed and compared it's performance with the conventional APJ through experiment with specimens. As a result of the experiment, APJ had crack formation on both ends of the gap plate, spreading to the surface of the expansion joint. With this result, we can conclude that the reason for early damage is the tension failure due to the concentration of strain in the asphalt mixture along the end of gap plate and the debonding along the joint section. In contrast, the newly developed BFLJ induced even transformation in the joint by applying moving stud and high performance material, and resolved APJ's disadvantage of strain concentration. Therefore, it could be seen that the newly developed BFLJ could overcome the disadvantages of APJ and prevent early damage.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.23 no.2
• /
• pp.89-99
• /
• 2021

This study was carried out to understand how factors of decomposition such as quality of the substrate (tree species), forest types, and soil·meteorological conditions affect decomposition rates and dynamics of carbon (C) and nitrogen (N) of branches in adjacent Pinus densiflora and Quercus variabilis stands in Sancheong and J inju in Southern Korea. The branch bags (30 cm × 30 cm) with branch samples (a diameter of 2.0 - 4.0 cm and length of 10 cm) were placed on the forest floor at each stand in May 2018. The branch bags were collected in August and November 2018, February and May 2019, respectively. The decomposition rates of branches in P. densiflora stands were 4.49 % for Sancheong, and 5.75 % for Jinju. Whereas, the decomposition rates in Q. variabilis were 20.01 % for Sancheong, and 24.68 % for Jinju, respectively. The decomposition of branches was more rapid in Q. variabilis compared with P. densiflora in both regions. C and N in decomposed branches were more mineralized in Q. variabilis, whereas C and N were more accumulated in P. densiflora. These results indicated that the decomposition rates, C and N of decomposed branches may be affected by differences in substrate quality such as initial N concentration and C/N ratio rather than differences between both regions including different environmental factors.

• Journal of the Korean GEO-environmental Society
• /
• v.22 no.3
• /
• pp.5-13
• /
• 2021

Due to population growth and industrial development, the amount of industrial waste is increasing every year. In particular, in a thermal power plant using finely divided coal, a large amount of coal ash is generated after combustion of the coal. Among them, fly ash is recycled as a raw material for cement production and concrete admixture, but about 20% is not utilized and is landfilled. Due to the continuous reclamation of such a large amount of coal ash, it is required to find a correct treatment and recycling plan for the coal ash due to problems of saturation of the landfill site and environmental damage such as soil and water pollution. In recent years, the use of a fluid embankment material that can exhibit an appropriate strength without requiring a compaction operation is increasing. The fluid embankment material is a stable treated soil formed by mixing solidifying materials such as water and cement with soil, which is the main material, and has high fluidity before hardening, so compaction work is not required. In addition, after hardening, it is used for backfilling or filling in places where compaction is difficult because higher strength and earth pressure reduction effect can be obtained compared to general soil. In this study, the possibility of use of fluidized soil using high water content cohesive soil and coal ash is considered. And it is intended to examine the flow characteristics, strength, and bearing capacity characteristics of the material, and to investigate the effect of reducing the earth pressure when applied to an underground burial.