• Food Science and Preservation
• /
• v.23 no.1
• /
• pp.34-41
• /
• 2016

The quality characteristics of black garlic vinegar produced by acetic acid fermentation were analyzed over a 25 day period. Black garlic vinegar was produced using black garlic 3, 6, 9 and 12 folds with water, and initial alcohol concentrations of 6~12%. The pH values of the vinegar samples were in range of 3.85~4.46 after 25 days fermentation, and the sugar contents were highest after 9 days of fermentation ($12.00{\sim}13.50^{\circ}Brix$). The total polyphenol concents of vinegars were in the range of 20.65~52.04 mg/100 mL 25 days fermentation. Pyrogallol and vanillic acid were detected in the completely fermented vinegars, and their contents increased with black garlic content. Five organic acids (lactic acid, acetic acid, citric acid, succinic acid and propionic acid) were detected after 25 days of fermentation, with the total amount of organic acids being 5,327.34~6,307.64 mg/100 mL, and the total abetic acid contents beging the highest of the organic acids at 4208.90~5,570.29 mg/100 mL. After 25 days of fermentation, the total minerals contents were higher, and depending on the quantity of black garlic added. Of the minerals, the of potassium content was the highest (366.23~1,619.67 mg/L).

• Korean Journal of Food Science and Technology
• /
• v.28 no.3
• /
• pp.399-404
• /
• 1996

Encapsulation of lysozyme using lecithin vesicles and its stimilated release properties were studied. Lecithin vesicles were prepared by the dehydration-rehydration (DR)method. The highest encapsulation efficiency (EE) value of 80.1% was obtained by sonicating the multilamellar vesicles (MLVs) at 100 KHz for 120 min in bath sonicator. The value of entrapment progressively increased with the concentration of lysozyme, while the EE value decreased with the increase of enzyme concentration up to 50mg per 100mg per 100mg of lecithin, and then became nearly constant. At the pH of 5.9, only a small amount of lysozyme was released from DR vesicles during incubation at $37^{\circ}C$ As the pH decreased to 3.0, lysozyme was released more rapidly. Lysozyme release was accelerated for 24h and reached a plateau after 72h incubation with 1% Tween 80, $Ca^{2+}$ gave a pulse-like-release in the first hour, which was followed by a slow release.

• Fire Science and Engineering
• /
• v.33 no.4
• /
• pp.35-40
• /
• 2019

In this study, the mass flow rate of the heat release rate equation, which is the major factor of the oxygen consumption method, was analyzed for the fundamental investigation of the cone-calorimeter (5 m length and 0.3 m diameter). The shapes of a completely empty inside, 3 mm pore diameter mesh and pore diameter 10 mm honeycomb with 0.76 porosity were constructed using the cone-calorimeter. To calculate the mass flow rate, four bi-directional probes and thermocouples were installed in a uniform position in the vertical direction of flow. The velocity gradient and flow perturbation were measured from the increase in Reynolds number. As the flow capacity increased, the speed gradient increased in all three shapes relative to the turbulence intensity. In addition, the deviation of extended uncertainty to the mass flow was completely low in the order of empty space, mesh (d_p = 3 mm) and honeycomb (d_p = 10 mm and 𝜖 = 0.76) at the 95% confidence level. The results can be used in designs to improve the flow stability of the cone calorimeter.

• Journal of the Mineralogical Society of Korea
• /
• v.21 no.4
• /
• pp.435-442
• /
• 2008

Natural, synthetic, and treated diamonds were studied by NMR and EPR. It was demonstrated that natural and synthetic diamonds, treated and non-treated diamonds, high pressure high temperature (HPHT) treated and electron beam treated diamonds could be distinguished among each other based on the $^{13}C$ NMR spectra acquired for relatively short periods of 100 minutes. The $^{13}C$ NMR linewidths of gem quality synthetic diamonds were broader than 1.6 ppm due to the paramagentic effects of transition metals, generally used as catalysts, while the linewidths of gem quality natural diamonds were narrower than 0.5 ppm regardless of the methods of treatment. The linewidth (0.5 ppm) for a HPHT treated, gem quality natural diamond was as broad as more than twice of the linewidth (0.2 ppm) of an electron beam treated diamond. The $^{13}C$ NMR signal intensities of treated, gem quality natural diamonds were as strong as more than 10 times of the intensities of non-treated, gem quality natural diamonds. When correlated with the concentrations of the paramagnetic defects (electrons) obtained from the EPR spectra, the relative $^{13}C$ NMR signal intensities increased in proportion to the concentrations of the paramagnetic electrons contained in each sample but the electron beam treated diamond was an exception. This suggested that the lattice component, in addition to the paramagnetic defect component, should also be considered in determining the $^{13}C$ NMR signal intensity of the electron beam treated diamond.

• Journal of the Korean Society for Railway
• /
• v.17 no.4
• /
• pp.270-280
• /
• 2014

In this study, to examine the causes of cracks in continuously reinforced concrete tracks (CRCTs) and the main factors affecting cracking, a field survey on the status of cracks and crack patterns in the Gyeong-bu high speed line was conducted, and the crack patterns of CRCT due to the temperature difference between the top of the slab (TCL) and the bottom of the subbase (HSB) and the drying shrinkage of concrete were predicted by a nonlinear finite element model considering the structure of CRCT. The results of the numerical analysis show that cracks will be developed at the interface between the sleeper and the TCL, and under the sleeper due to the temperature difference and concrete shrinkage. This corresponds well to the crack locations found in the field. Also, it is found that the most significant factors are the coefficient of thermal expansion with respect to the temperature difference, and the drying shrinkage strain with respect to shrinkage. According to the results, the reinforcement ratio should be carefully determined considering the structures of CRCT because the crack spacing is not always proportional to the reinforcement ratio due to the sleepers embedded in the TCL.

• Korean Journal of Agricultural Science
• /
• v.19 no.1
• /
• pp.65-78
• /
• 1992

The paper describes the comparison between observed and predicted stress-strain characteristics of marine silty clay in Dangjin district. For prediction, the hyperbolic model which is applied the parameters acquiring by physical and triaxial compression test was adopted, and the obtained results were summarized as follows: 1. The Young's modulus were increased with decreasing of moisture contents and increasing of dry density. 2. The most affective factor to hyperbolic model is lateral stress and dry density. and than cohesion and internal friction angle. 3. The comparision between the statistical and hyperbolic values of maximum deviator stress have few accordance. and the statisticals is lower than the hyperbolics. 4. Without. much labor and tiresome procedures, effective computer program was made and applied, but technical procedure for prevents test errors of parameter calculation is importants.

• Journal of the Korean Chemical Society
• /
• v.33 no.1
• /
• pp.70-81
• /
• 1989

Reverse phase liquid chromatographic elution behaviors of salicylic acid and its derivatives were studied with classical and modern high-performance liquid chromatography(HPLC) using Amberlite XAD-4 and XAD-7 resin packed columns. Capacity factors(k') were determined in the comparatively high concentration(from 0. 010F to 0. 150F) of ferric nitrate-50% methanol solution to elucidate the elution behaviors with classical method. On the other hand, k's were measured in the various concentrations of methanol and ferric nitrate(from $2.5{\times}10^{-4}F\;to\;1.0{\times}10^{-3}F$) solution of pH 2. 25 and 293K with HPLC to explain the elution mechanism of them, and to find their optimum separation condition. As a result, it was found that log k's of salicylic acid and its derivatives were decreased with increasing the concentration of ferric ion, and the decreasing slopes of the compounds on the increasing ferric ion concentrations were related with each stability constant of ferric salicylates. Some isomers of derivatives of salicylic acid could be separated in the optimum condition.

• Korean Journal of Food Science and Technology
• /
• v.38 no.2
• /
• pp.284-289
• /
• 2006

Effects of mulberry fruit extract (MFE) on the levels of serum mineral and serum oxidative stress markers on 31 middle-aged humans (16 males and 15 females) supplemented with MFE for 4 weeks were investigated. Contents of mineral per 100 g MFE were 80.66 (Ca), 12.26 (Mg), 6.26 (Fe), 0.05 (Cu), and 4.04 mg (Zn). Relative scavenging activities of MFE and its cyanidin-3-glucoside on 1,1-diphenyl-2-picrylhydrazyl (DPPH) were 34 and 85%, respectively, using ascorbic acid as standard. Anthropometry measurements, serum mineral (Ca, Mg, Fe, Cu, and Zn)levels, and serum oxidative stress markers were analyzed before and after supplementation of MFE. After supplementation of MFE, no significant differences were observed in anthropometry measurements and levels of serum thiobarbituric acid reactive substance (TBARS) in males and females, and ferric-reducing ability plasma (FRAP) in males, whereas serum mineral levels (Fe in males, and Fe, Cu, and Zn in females) and serum FRAP levels (both males and females) increased significantly.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.44-44
• /
• 1999

저진공(1 kPa~ 100 kPa)은 대기압 측정, 비행고도, 기체의 온도 측정, 질량의 부력 보정, 레이저의 굴절률 측정등에 사용되는 영역으로 과학적 중요성을 갖고 있다. 또한 대기압 이상의 압력 측정과 고진공 측정의 경계적 역할도 수행하고 있어 압력 표준기의 국제 비교에 필수적으로 권장되는 역역이다. 이 영역에 주로 사용되는 압력 표준기는 수은 압력계(Mercury manometer)와 분동식 압력계(Deadweight piston gauge or Pressure)가 있다. 이들은 이동이 불편하거나 불가능하므로 표준기의 국제 비교에 사용되는 전달 표준기로는 보다 이동이 간편한 탄성 압력계인 CDG(Capacitance diaphragm Gauge)가 있다. 이 게이지는 반도체 산업의 공정 제어용으로도 많이 사용되고 있다. 그러나 게이지와 함께 사용되는 컨트롤러의 부피가 크고 무거우며 영점 이동이 커서 측정때 마다 재조정하여야 하는 단점이 있다. 본 논문에서는 이 같은 단점을 극복하기 위해 수정빔 진동형 진공 센서를 잔달 표준기로 사용하는 것에 대한 연구를 수행하였다. 수정빔 진동형 압력 센서는 수정빔으 공진주파수가 스트레인에 비례하는 것을 이용하여 제작된 센서로 주로 대기압 이상의 고압 측정에 많이 사용되고 있다. 먼저 수정빔의 압력과 주파수간의 관계를 측정하고 또한 내장된 수정 온도센서의 공진 주파수를 측정하여 온도 보상을 위한 자료로 사용하였다. 규격에 나와 있는 수정빔의 기하학적 형상으로부터 거동에 관한 이론 모델식을 구하고 압력교정 자료로부터 얻어진 데이터를 이 식과 비교 분석하여 적합한 특성식과 인자를 구하였으며 게이지의 불확도를 추정하였다.모델은 길이가 유한한 0-차원 실린더 모델로 가정하였고, 이에 대한 기하학적 성질 및 열역학적 성질은 유효계수를 고려하여 산출하였다. 진공용기 이중 벽 내부로 흐르는 질소가스의 유량과 온도의 계산은 진공용기 내벽과 외벽을 각각 독립적인 열전달 요소로 가정하여 구성한 모델을 이용하였다. 전체 해석에서 각 열전달 요소의 비열 값은 온도에 따라 변화하는 비열의 특성을 반영하였으며. 진공용기와 플라즈마 대향 부품의 방사율(emissivity)은 앞서 가정했던 각 온도 상승 곡선에 대해서 각각 0.1, 0.2, 1.3의 경우를 가정하여 계산하였다. 직선적으로 증가하는 온도 상승 곡선중 2$0^{\circ}C$/hr의 온도상승율을 갖는 경우가 다른 베이킹 시나리오 모델에 비해 효과적이라 생각되며 초대 필요 공급열량은 200kW 정도로 산출되었다. 실질적인 수치를 얻기 위해 보다 고차원 모델로의 해석이 필요하리라 생각된다. 끝으로 장기적인 관점에서 KSTAR 장치의 베이킹 계획도 살펴본다.습파라미터와 더불어, 본 연구에서 새롭게 제시된 주기분할층의 파라미터들이 모형의 학습성과를 높이기 위해 함께 고려된다. 한편, 이러한 학습과정에서 추가적으로 고려해야 할 파라미터 갯수가 증가함에 따라서, 본 모델의 학습성과가 local minimum에 빠지는 문제점이 발생될 수 있다. 즉, 웨이블릿분석과 인공신경망모형을 모두 전역적으로 최적화시켜야 하는 문제가 발생한다. 본 연구에서는 이 문제를 해결하기 위해서, 최근 local minimum의 가능성을 최소화하여 전역적인 학습성과를 높여 주는 인공지능기법으로서 유전자알고리즘기법을 본 연구이 통합모델에 반영하였다. 이에 대한 실

• The KIPS Transactions:PartA
• /
• v.19A no.3
• /
• pp.129-138
• /
• 2012

In distributed memory architectures like clusters, each node stores a portion of data. How data is distributed across nodes influences the performance of such systems. The data distribution scheme is the strategy to distribute data across nodes and realize parallel data processing. Due to various reasons such as maintenance, scale up, upgrade, etc., the performance of nodes in a cluster can often become non-identical. In such clusters, data distribution without considering performance cannot efficiently distribute data on nodes. In this paper, we propose a new data distribution scheme based on the number of cores in nodes. We use the number of cores as the performance factor. In our data distribution scheme, each node is allocated an amount of data proportional to the number of cores in it. We implement our data distribution scheme using the Chapel language. To show our data distribution is effective in reducing the execution time of parallel applications, we implement Mandelbrot Set and ${\pi}$-Calculation programs with our data distribution scheme, and compare the execution times on a cluster. Based on experimental results on clusters of 8-core and 16-core nodes, we demonstrate that data distribution based on the number of cores can contribute to a reduction in the execution times of parallel programs on clusters.