• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.4
• /
• pp.117-124
• /
• 2009

The purpose of the study was to improve quality of high volume fly ash concrete. The study evaluated on the possibility of early quality improvement of high volume fly ash concrete with early strength gain admixture ('GA' below) developed by the preceding research. The study regarded applying naphthalene admixture ('NA' below) to mix proportion substituting FA 15 % to be plain. In the event of substituting FA 20, 25 and 30 %, the study compared engineering properties of concrete with plain by applying GA. Because of features of fresh concrete, fluidity falls down when GA is applied. Therefore, its use amount shall be increased. Only, in W/B 60 %, it was beneficial since slump loss was reduced about 35~70 mm than plain. The study could see that AE use should be increased proportionally since air content was reduced by coming from AE absorption operation of unburned coal content included in FA according to an increase in the amount of FA use. Reduction effect of bleeding could be anticipated since the amount of bleeding appeared at least in FA 20 %. Because of hardened concrete, time of setting appeared in the same level as plain when GA was applied. Therefore, it is judged that delay of setting can be reduced. In compressive strength, the study could check the same strength development as plain when GA was applied, having nothing to do with W/B and curing temperature. However, it is thought that we shall pay attention to GA use in the event of FA 30 % substitution. Freezing and melting resistance had less early value than plain. However, it is judged that there will be no problem of frost resistance since there is no a large difference between freezing and melting resistance and plain in overall. In accelerated neutralization, it was analyzed that a problem of weakening in neutralization appointed as a demerit when FA was applied in mass in proportion with GA use could be settled to some extent.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.40 no.6
• /
• pp.757-767
• /
• 1995

This experiment was done to determine the optimum concentration of IAA for root development in plants regenerated from the callus culture of barley embryos. Two concentrations of 2,4-D, 3ppm and 5ppm selected as an optimum among five different concentrations in the previous experiment were used for callus induction and proliferation in this experiment. For callus induction, 3ppm of 2,4-D produced 35.6% in immature embryos and 4.4% in mature embryos, while 5ppm gave 33.8% in immature and 5.6% in mature embryos. Out of 320 immature embryos cultured, 111 embryos were induced to calli and 684 plants were produced from them, while only 16 embryos were induced to calli from 320 mature embryos and 92 plants were restored. The rates of callusing and plant regeneration were 34.7%, 214% in immature embryos and 5.0%, 28.7% in mature embryos, respectively. The average root lengths and root numbers of plants restored from callus at five different IAA concentrations of 0ppm, Ippm, 5ppm, l0ppm and 30ppm were 7.9mm, 3.6; 18.4mm, 5.2; 16.1mm, 3.9; 8.5mm, 3.5 and 6.4mm, 3.4, while plants directly obtained from mature embryos were 14.8mm, 4.9; 4.9mm, 3.6; 4.3mm, 3.1; 3.6mm, 2.6 and 3.2mm, 2.1, respectively. Therefore, 1ppm gave the best result for the root. promotion in callus, whle 0ppm, a control, gave the largest root developmemt in embryos. High concentration of lAA(30ppm) in callus and any exogeneous supplement of lAA in embryos negatively affected to the root lengths and root numbers. Genotypic effect was also observed in given four varieties, Bruce, Klages, Olbori and Albori. For chromosome doubling, when 0.1% colchicine was applied on 428 plants under three different conditions such as air circulation, temperatures and growth stages, 319 plants of doubled haploids were obtained so that the rate was 74.5%

• Korean Journal of Heritage: History & Science
• /
• v.53 no.3
• /
• pp.62-79
• /
• 2020

The rock-carved seated Avalokiteśvara statue at Ganghwa Bomunsa Temple is a giant rock-carved Buddhist statue that was built in 1928 during the Japanese colonial era. Although it is a year-recorded Buddhist statue that occupies a prominent place in modern Korean Buddhist sculpture history, it has not been the subject of in-depth discussion due to weak research on modern Buddhist sculptures. In this study, to examine the various significant aspects of the rock-carved Seated Avalokiteśvara statue at Bomunsa Temple as a modern Buddhist sculpture, I have managed to determine its construction year, artificers, and patrons by deciphering the inscription around the rock-carved statue; in addition I have researched the effects of the rock shapes and landforms on the formation of the Buddhist statue by comparing and analyzing the points of view of both artificers and worshipers. I have also identified the specific circumstances of the time of construction from interviews with the descendants of artificers. A monk from Geumgangsan Mountain, Lee Hwaeung, took the role of sponsor and chief painter to construct the rock-carved seated Avalokiteśvara statue at Bomunsa temple. In the beginning of its construction in 1928, more than 100 donators jointly sponsored the construction of the statue. Gansong Jeon Hyoungphil sponsored alone at the time of the place of worship's expansion in 1938. Bomunsa Temple has been regarded as one of the top-three sacred places of Avalokiteśvara Bodhisattva together with Naksansa Temple in Yang Yang and Boriam in Nam Hae, due to the construction of the rock-carved statue. It took about three months to construct the statue. Lee Hwaeung drew a rough sketch and then Un Songhag and five masons from Ganghwa Island took part in the carving process. We can observe the line drawing technique around the rock-carved statue because the statue was carved based on the rough sketch of the monk painter. The aspect of Lee Hwaeung as a painter is revealed; therefore, we can identify the clue of painting pattern leading to Seogongchulyou- Hwaunghyoungjin- Ilonghyegag. The rock-carved seated Avalokiteśvara statue at Bomunsa Temple is a typical Avalokiteśvara that wears a jeweled crown and holds Kundica. It makes a strong impression as it has a big square-shaped face and a short neck and is unsophisticated in general. The artificers solved the issue of visual distortion of the rock-carved statue caused by carving on a 10-meter high and 40-degree sloping rock by controlling motion to its maximum, omitting detailed expression by emphasizing symmetry, and adjusting the head-to-body proportion to be almost one-to-one. In this study, especially, I presume the unified form of sacred sculptures and Buddhist altars, without making a Buddhist altar like the rock-carved seated Avalokiteśvara statue at Bomunsa Temple, to be a key characteristic of modern Buddhist sculptures. Furthermore, I make newly clear that the six letters of Sanskrit carved on nimbus, which had been interpreted as a Six-Syllable Mantra, are a combination with Jeongbeopgye and Sabang Mantras. In addition, three iron rings driven on eaves rock were used as a reference point, and after construction they were used as a decoration for the Bodhisattva with hanging wind chimes.

• Journal of Yeungnam Medical Science
• /
• v.25 no.1
• /
• pp.1-18
• /
• 2008

Although Lamivudine and adefovir dipivoxil are efficacious drugs for preventing hepatocellular carcinoma (HCC) in chronic hepatitis B patients, their efficacy is far from completely satisfactory. The risk of liver cirrhosis and HCC begins to increase at an HBV DNA level of $10^4$ copies/ml. Even with latent or past HBV infection, episomal covalently closed circular DNA(cccDNA) plays a key rolein the persistence, relapse and resistance of HBV in its natural course or during therapy. The annual incidence of HCC in YUMC is 1.8% and 4.7% patients/year in the antiviral treatment and control groups, respectively. The ability to achieve a high rate of sustained HBV suppression with low risk of drug resistance is the ultimate goal in the treatment of chronic HBV infection. The efficacy of universal immunization with striking reductions in the prevalence of HBV in localized countries needs to be spread worldwide. With hepatitis B immunization and effective antiviral therapy, global control of HBV infection and HBV-related complications, including HCC, are possible by the end of the first half of the $21^{st}$ century.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.6
• /
• pp.899-915
• /
• 2018

In this study, in order to construct an eco-friendly advanced road transportation network, the multi-layer tunnel, which is a small-sized car road, is designed to have a height of less than 60 cm. However, the shape of the tunnel is low and the height of the traffic sign is small. In order to solve these problems, traffic sign characters were designed in three dimensions, and the possibility of applying the design of the three - dimensional sign that can obtain greater visibility than the existing signs at the same distance and the possibility verification through virtual simulation were performed. The three-dimensional sign is horizontally installed on the ceiling of the multi-layer tunnel. To be seen vertically, it is enlarged by a certain ratio by the perspective, and the width and height are enlarged. Respectively. In addition, 3D simulation was performed to verify the visibility of the stereoscopic signs when the driver ran through the stereoscopic sign design specifications. As a result of the design and experimental study, it was confirmed that the stereoscopic sign could be designed through the theoretical formula and that it could provide the driver with a larger traffic sign character because there is no limitation of the facility limit compared to the existing vertical traffic sign. Also, we confirmed that it can be implemented in the side wall by using the stereoscopic sign design principle installed on the ceiling part. It was confirmed that the design of the stereoscopic sign can be designed to be smaller as the distance that the driver visually recognizes the sperm is shorter, the height of the protrusion vertically at the lower part of the stereoscopic sign becomes higher. As a result of 3D simulation running experiment based on the design information of the stereoscopic sign, it was confirmed that the stereoscopic sign is visually the same as the vertical sign at the planned distance. Although the detailed research and institutional improvement of stereoscopic signs have not been made in Korea and abroad, it is evolved into a core technology of new road traffic facilities through various studies through the possibility of designing and applying stereoscopic signs developed through this study Expect.