• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.410-411
• /
• 2019

본 논문에서는 홀 센서를 사용하지 않고 단상 영구자석 동기 전동기의 초기 회전자 자극을 검출하여 안정적인 오픈루프 기동 및 센서리스 운전 기법을 제안한다. 제안한 회전자 초기 자극 검출 방법은 비대칭 공극을 갖는 단상 영구자석 동기 전동기에 고주파 전압을 인가한 후 회전자 초기 극성에 따른 자기회로의 비 포화 및 포화여부를 저역통과필터를 이용하여 빠르게 검출하는 방법을 제안하였다. 제안된 초기 자극 검출 방법은 다수의 실험 결과를 통해 안정적 기동 및 센서리스 운전이 가능함을 입증하였다.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.812-813
• /
• 2015

본 논문은 권선계자형 동기전동기(WFSM : Wound Field Synchronous Motor)의 토크리플을 저감시키기 위한 설계 기법을 제시하고자 한다. 돌극형 회전자의 극판(Pole Plate)을 좌우 비대칭으로 축방향 길이을 반으로 나누어 2가지 모델에 대한 합성 파형을 분석한다. 기존의 연구된 스큐 기법과 비슷하게 합성 파형에 의해서 토크리플이 저감된다. 그리고 비대칭 기법과 스큐 기법을 비교하는 형식으로 운전 영역 내에서의 몇 가지 운전 점에서 특성을 비교 분석하였다.

• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.435-436
• /
• 2020

본 논문에서는 단상 영구자석 동기 전동기의 센서리스 운전을 위한 회전자 자극 검출 기법을 제안한다. 제안한 회전자 초기 자극 검출 방법은 비대칭 공극을 갖는 단상 영구자석 동기 전동기에 고주파 전압 및 옵셋 전류를 인가하여 회전자 자극 위치에 따른 전류 옵셋의 크기를 검출함에 있다. 이를 위해 가상의 dq축 모델을 이용한 고정자 전류의 크기를 비교하여 회전자 자극을 검출하고자 한다. 제안된 방법은 다수의 실험 결과를 통해 타당성을 입증하였다.

• Journal of IKEEE
• /
• v.23 no.3
• /
• pp.1020-1026
• /
• 2019

In this paper, a rotor polarity detection algorithm is proposed to control the single-phase permanent magnet synchronous motors(SP-PMSMs) for high speed sensorless operation. Generally, the sensorless control of a SP-PMSM is switched to the sensorless operation in a specific speed region after the open loop startup. As a result, it is necessary to detect the rotor polarity to maintain a constant rotational direction of the SP-PMSM at the starting process. There, this paper presents a novel rotor polarity detection method using a high frequency voltage signal and offset current which is generated by current regulator. The proposed algorithm verified the effectiveness and usefulness of the rotor polarity detection through several experiments.

• Journal of KSNVE
• /
• v.9 no.4
• /
• pp.835-840
• /
• 1999

Cause of excessive vibration signals with twice the rotational speed of a 2-pole generator rotor in balancing for fossil power plants was investigated. The 2-pole generator rotor is treated as a typically asymmetric rotor in vibration analysis, and produces asynchronous vibration with twice the rotational speed for its own inertia and stiffness asymmetry. This paper introduces practical balancing procedure and experimental vibration data of the asymmetric 2-pole rotor in balancing, and presents the results of investigation into sources of the excessive vibration signals.

• Journal of IKEEE
• /
• v.23 no.2
• /
• pp.622-627
• /
• 2019

This paper propose an initial rotor position detection method for sensorless operation of a single-phase permanent magnet synchronous motor(SP-PMSM) with asymmetric air-gap. In general, the sensorless control based on back-emf estimation is difficult to estimate the back-emf at the zero and low speed regions. For this reason, an open loop start-up technique is indispensable, and it is also necessary to detect the initial position of the rotor in order to rotate in a certain direction. In this paper, we propose a method to detect rotor polarity by adding offset voltage to high frequency voltage signal based on the magnetic characteristics of SP-PMSM. The validity and usefulness of the proposed algorithm are verified through several experimental results.

• Proceedings of the KIPE Conference
• /
• 2011.11a
• /
• pp.153-154
• /
• 2011

본 논문은 비대칭 2상 SRM의 센서리스 속도제어를 위한 초기각 검출 및 초기 기동방식과 자속관측기를 적용한 센서리스 제어에서 전동기의 온도 및 파라미터 변동에 의한 자속 오차 성분으로 인해 발생하는 위치 추정오차를 보상하기 위한 새로운 보상기를 제안한다. 제안된 방식은 전압펄스 인가로 초기각을 검출하고 검출된 초기 위치정보를 바탕으로 동일한 전압펄스 인가를 통해 비여자상이 여자상이 되는 회전자 위치를 검출하여 상여자를 교체하는 초기기동을 통해 자속관측기를 적용한 센서리스 제어로 안정적으로 진입하도록 한다. 이 때, 제안된 추정위치 보상기를 통해 추정된 센서리스 위치를 순시적으로 보상한다.

• Journal of IKEEE
• /
• v.24 no.4
• /
• pp.1004-1010
• /
• 2020

This paper proposes an initial rotor magnetic pole detection method for single-phase permanent magnet synchronous motors. The target motor cannot obtain position information based on the back emf in the low speed and stop state. Therefore, an open loop starting process is required, and in this process, initial rotor position information for low current and soft start is need. The proposed initial rotor magnetic pole detection algorithm considers the effect of asymmetric air- gap and magnetic flux. In addition, the high-frequency voltage signal injection and the offset voltage for accurate detection is used. As a result, the permanent magnet poles are is determined by acquiring the maximum value of the induced current using the virtual dq-axis.

• Journal of Power System Engineering
• /
• v.11 no.1
• /
• pp.16-19
• /
• 2007

The large generator rotor used in fossil power plant has the possibility of high 2X vibration due to asymmetric shaft stiffness. The generator rotor is machined into pole faces to reduce stiffness difference and then is tested through 2X vibration measurement when the balancing works are performed in the balancing shop. However, there are many cases of large difference values between 2X vibration in the balancing shop and 2X vibration in site. This paper presents a new method to estimate 2X vibration in site with more accuracy and applied for the retrofit of a fossil 400 MW class deteriorated generator. It shows that the new generator rotor is manufactured with a good 2X vibration characteristics and is operated in a low 2X vibration level although the generator rotor has high 2X vibration in the balancing shop.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.6 no.1
• /
• pp.43-53
• /
• 2002

Current torsional provisions focus n restricting torsional effect of asymmetric wall structures by proportioning strength of wall based on the traditional assumption that stiffness and strength are independent. Recent studies have pointed out that stiffness of structural wall is dependent on the strength. This implies that actual stiffness of walls can be determined only after torsional design is finished and current torsional provisions may result in significant errors. To overcome this shortcoming, this paper proposes deformation based torsional design for asymmetric wall structures. Contrary to the current torsional provisions, deformation-based torsional design uses displacement and rotation angle as design parameters and calculates base shear for inelastic torsional response directly. Main purpose of deformation based torsional design is not to restrict torsional response but to ensure intended torsional mechanism according to the capacity design concept. Because displacement and rotation angle can be used as performance criteria indicating performance level of asymmetric structures, this method can be applied to the performance based seismic design effectively.