• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.6
• /
• pp.2359-2368
• /
• 2013

Cone penetration tests (CPTs) have been increasingly used for site characterizations. However, the site investigations using CPTs are often limited due to soil conditions depending on the cone size and capacity of the CPT system. The small sectional area of a miniature cone improves the applicability of the CPT system due to the increased capacity of the CPT system. A continuous intrusion system using a coiled rod allows fast and cost effective site investigation. In this study, the performance of the continuous intrusion miniature cone penetration test (CIMCPT) system has been evaluated by comparison tests with the standard CPT system at several construction sites in Korea. The results show that the CIMCPT system has a same performance with the CPT system and has advantages on the mobility and applicability. According to field verification tests for scale effect evaluation, the cone tip resistance evaluated by CIMCPT overestimates by 10% comparing to standard CPTs. A crawler mounted with the CIMCPT system has been implemented to improve accessibility to soft ground, and has shown improvement over the truck type CIMCPT system. Therefore, the improved CIMCPT system can be utilized as a cost effective and highly reliable soil investigation methodology to detect the depth of soft ground and to evaluate soil classification.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.26 no.5
• /
• pp.514-522
• /
• 2020

To understand the ecotoxicological differences between representative Skeletonema sp. and Dunaliella tertiolecta, both producers as international standard test species for marine ecotoxicity testing, we compared each standard test method, and comparatively analyzed the suitability of the species for environmental assessment and their sensitivity to various test substances. Although most of the test conditions were the same in each method, there were differences in limitation of pH changing and the initial inoculation density in the validation criteria, which is supposed to originate from the low growth rate of D. tertiolecta. In terms of suitability, both species showed consistency in test performance by repeatedly meeting the validation criteria required by the standard test methods. The salinity ranges available for testing were 20 and 10 psu for Skeletonema sp. and D. tertioelecta, respectively. Finally, regarding sensitivity, the toxicity sensitivity of Skeletonema sp. was relatively higher than that of D. tertiolecta for the reference toxicant, actual polluted water discharged (ballast water), and other chemicals. This implies that using at least two species of microalgae from different classification groups could help increase the reliability and objectivity of test results in the performance of marine ecotoxicity tests using producers.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.2 no.1
• /
• pp.93-102
• /
• 2006

In order to use a recycled aggregate concrete for precast concrete box structures, the structural behaviors should be analytically and experimentally evaluated. In this study, full-scale precast concrete box structures are manufactured using the recycled aggregate (30% replacement) and natural aggregate. Then, the flexural failure test and shear failure test as well as water leakage lest for the structures arc carried out. First of all, test results of compressive strength show that recycled aggregate concrete is only 4% lower than normal concrete. In the flexural and shear failure test, the structural performances of precast box using the recycled aggregate concrete are 95% of the capacities of normal precast concrete box or more. Especially, the water leakage test shows that leakage pressure of recycled concrete box is more than the critical value, 60kPa, as well as 9% higher than normal precast concrete box. These test results are analyzed and compared with results of finite clement analysis. The comparison shows that test results are more excellent than analytical results. Also, the comparison confirms the applicability of recycled aggregate concrete for the use as practical precast concrete box structure.

• Journal of Aerospace System Engineering
• /
• v.16 no.4
• /
• pp.88-94
• /
• 2022

The vibration mode measurement test measures the natural vibration characteristics of the target specimen. The measured natural mode characteristics are compared with the numerical analysis result to verify the reliability of the numerical analysis. If necessary, it is used to supplement the numerical analysis model of the specimen used for the dynamic characteristic analysis. In this paper, the natural frequency and natural mode of the external fuel tank are respectively obtained through the vibration mode measurement test and the numerical analysis, using the finite element model. The results are compared to verify the reliability of the numerical analysis model of the external fuel tank to apply to the entire aircraft model. To measure the vibration mode of the test specimen, a bungee cord was used, to simulate the free boundary condition for the test specimen. And, 3-axis accelerometers were installed on the test specimen. The response characteristics of the test specimen were measured, by excitation with an impact hammer. As a result of the test, after performing the frequency response analysis on the response acceleration, the natural frequency of the test specimen and its vibration mode were confirmed. The reliability of the numerical analysis model was verified by comparing the frequency and vibration mode, obtained through the test and the numerical analysis.

• Land and Housing Review
• /
• v.7 no.4
• /
• pp.281-289
• /
• 2016

Structural experiment result showed that PHC(d=600mm) Pile used as a common compression member could resist 83.6 ~ 91.6 tonf of ultimate tension force, if the adhesion of P.C. bar of PHC pile to the concrete foundation is strengthened. Considering a proper safety factor to ultimate tension strength, PHC pile can substitute the anti-floating anchor, or reduce the number of anchors. For this purpose, pullout resistance behavior of a Bored pile embedded in real ground as well as structural tension strength of PHC pile must be evaluated. This study performed the static pullout tests to evaluate the pullout behavior of bored pile, and compared the test results with design value of side resistance. To evaluate the pullout resistance easily, static pullout test results were compared with dynamic loading test results using PDA. As a result, cement paste of the bored pile was hardened which is after 15 days, LH side resistance design value corresponded well to the Static pullout test results, also to the side resistance evaluated by dynamic loading test.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.8
• /
• pp.5095-5108
• /
• 2014

The aim of this study was to compare the perceptions of the role performance of a clinical research coordinator (CRC) between the investigators and clinical research associates (CRAs). Data was collected using a structured questionnaire from 39 investigators and 68 CRAs in 4 hospitals from March 7 to November 30, 2011 and analyzed using descriptive statistics and a t-test. The investigators and CRAs were aware of the importance of CRC's role and they all gave the highest values for patients care management. On the other hand, the score of the role performance items showed perceptional differences between investigators and CRAs. Therefore, the development of detailed job descriptions and manuals will be needed to reduce the perceptional differences in the role performance of the CRC.

• Journal of the Korean Society for Railway
• /
• v.12 no.4
• /
• pp.518-525
• /
• 2009

This paper describes the evaluation of structural performance test and finite element analysis to verify the design of Bimodal Tram made of sandwich composites. The sandwich composite applied to vehicle structure was composed of a aluminum honeycomb core and WR580/NF4000 glass fabric/epoxy laminate composite facesheet. The load tests of vehicle structure were conducted for vertical load, compressive load, torsion and modal analysis according to JlS E 7105. The structural Integrity of vehicle was evaluated by the measurement of displacement, stress and natural frequency obtained from dial gauge, strain gauge and gravity sensor, respectively. And finite element analysis using ANSYS v11.0 was done to compare with structural test. The results showed that the displacement, stress and natural frequency were in an good agreement with those of structural analysis using the proposed finite element models.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.973-976
• /
• 2008

Recently, it is increasingly reported that the deterioration of concrete structure under marine environments is due to diffusion and penetration of chloride ions. It is very important to estimate the diffusion coefficient of chloride ion in concrete. Estimation methods of chloride diffusivity by concentration difference is time-consuming. Therefore, chloride diffusivity of concrete is mainly conducted by electrically accelerated method, which is accelerating the movement of chloride ion by potential difference. However, there has not been any proper method for field quality control to closely determine the diffusion coefficient of chloride ion through accelerated tests using potential difference. In this paper, the various test methods for determination of chloride diffusion coefficient in concrete were investigated through comparison accelerated tests. From the results of estimated diffusion coefficient of chloride ion, relationship between the ponding test and acceleration test was examined.

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.04a
• /
• pp.364-365
• /
• 2003

토목합성재료는 지반위에 전폭으로 연결되어 사용되고 하중도 전장 및 전폭으로 전달되므로 인장강도 역시 전장 및 전폭으로 시험하는 것이 바람직하나 시험기의 용량 및 시험편 파지장치의 기술적 제약 상 전폭시험이 불가능하다. 현재 국내에서는 그래브 및 스트립 상태인 소폭으로 시험한 후 m당 인장강도로 환산하여 시공설계에 적용하고 있으므로 실제 재료의 설계 시 인장강도와 측정된 인장강도간에 차이가 있다. 그러나 미국, 유럽 등에서는 광폭시험편을 준비하여 인장강도를 측정함으로써 이러한 오차를 최소화하고 있다. (중략)

• Journal of the KSME
• /
• v.49 no.12
• /
• pp.54-59
• /
• 2009

자동차 부품 등 내구재의 파손은 긴 시간 동안 누적된 비교적 크기가 작고 빈도가 많은 입력하중에 기인하거나 상대적으로 적은 수의 큰 입력하중에 의해 유발된다. 미션 프로파일화(Mission Profiling)와 미션 합성(Mission Synthesis)은 어느 시험실에서나 공통된 장비를 이용하여 실제 환경에서 제품이 받는 동일한 수준의 피로 손상도를 보장하면서 훨씬 단축된 시험을 구현할 수 있는 시험 규격을 만들어 내는 과정이다. 이 글에서는 최신의 기술을 이용하여 이와 같은 가속화 진동내구 시험의 목적을 이루는 것에 관해서 소개한다.