• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.10
• /
• pp.974-984
• /
• 2012

This research introduces a new method to attenuate flip-over vibration generation in the flat blade windshield wiper by adjusting the contact pressure between the windshield glass and the blade. The knocking force in the flip-over action of the blade is decreased by inducing gradual tilting-over along the rubber strip of the blade. This gradual tilting-over is induced by introducing a non-uniform contact pressure distribution between the blade and windshield glass. The contact pressure distribution is adjusted by controlling the unloaded profile of the body spring in the blade using a procedure proposed in a previous study. Two blades, one blade designed to generate a uniform pressure distribution and the other designed to generate non-uniform pressure distribution, are developed using the procedure. Contact pressure distributions of the developed blades are measured using a special device and compared with the intended distributions confirming the similarities between the two groups. Vertical and lateral vibrations of the two blades are measured under realistic operating condition simulated by a wiper test rig. The vertical vibrations of the blade with non-uniform contact pressure are substantially smaller than corresponding vibrations of the blade with uniform contact pressure over the entire rubber strip.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.240-244
• /
• 2017

Experimental verification in the rig test stage for component development is a vital link between the aeromechanical design and structural integrity validation process. Based on this premise, Non-Intrusive Stress Measuring System was adopted on the axial compressor test rig to measure the static and dynamic tip deflection of all blades by using tip-timing sensors. Through analyzing vibration characteristics, we evaluated the vibratory stresses seen on the blades fatigue critical location; detected synchronous resonances which are the source of High Cycle Fatigue (HCF) in blades; presented non-synchronous vibration response by aerodynamic excitation and individual blade mis-tuning patterns.

• Aerospace Engineering and Technology
• /
• v.1 no.1
• /
• pp.1-7
• /
• 2002

This paper describes the analysis method about the dynamic characteristics and vibratory load through HDS(Helicopter Design Study). To analyze the dynamic characteristics of helicopter rotor blade, the natural frequencies and modes are calculated according to rotor operational speed(Ω). Generally the proximity of rotor natural frequency and N times of rotor operational speed is a dominant component to determine the helicopter vibration. Also we can predict the airframe vibration by calculating the airload of rotating blade exactly. We expect to establish the design procedure of rotor dynamics by describing the two major analysis methods necessary to rotor design.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1991.04a
• /
• pp.111-116
• /
• 1991

주파수 영역에서 로터의 thickness noise는 블레이드의 여러가지 기하학적인 조건, 즉 블레이드 수, 블레이드의 사잇각, 에어포일의 모양 그리고 반경방향의 블레이드 끝모양에 따라서 해석되어진다. 본 논문은 비 등간격 로터의 기하학적 조건에 따른 음신호의 위상간섭 영향을 고찰하기 위해서 등간격을 이루는 로터에 대해서 해석된 Hanson의 방법을 확장하였다. thickness noise를 6개의 블레이드를 가진 로터에 대하여 15.deg., 30.deg., 45.deg., 비 등간격을 이루는 경우와 각각에 45 tip angle로 sweepback되었을 때 먼 거리의 음향학적 음신호와 그 스펙트럼을 계산하였다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.04a
• /
• pp.492-497
• /
• 2011

Helicopter uses a rotor system to generate lift, thrust and forces, and its aerodynamic environment is generally complex. Unsteady aerodynamic environment arises such as blade vortex interaction. This unsteady aerodynamic environment induces vibratory aerodynamic loads and high aeroacoustic noise. Those are at N times the rotor blade revolutions (N/rev). But conventional rotor control system composed of pitch links and swash plate is not capable of adjusting such vibratory loads because its control is restricted to 1/rev. Many active control methodologies have been examined to alleviate the problem. The blade using active control device manipulates the blade pitch angle at arbitrary frequencies. In this paper, Active Trailing-edge Flap blade, which is one of the active control methods, is designed to modify the unsteady aerodynamic loads. Active Trailing-edge Flap blade uses a trailing edge flap manipulated by an actuator to change camber of the airfoil. Piezoelectric actuators are installed inside the blade to manipulate the trailing edge flap.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.04a
• /
• pp.680-681
• /
• 2012

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.4
• /
• pp.99-104
• /
• 2003

This paper described the general dynamic point for rotor design and the design procedure of low vibration blade. Generally, rotor rotating natural frequencies are determined to minimize hub loads, blade vibration and to suppress ground resonance at rotor design stage. First, through rotor frequency diagram, natural frequencies must be far away from resonance point and rotating loads generated from blade can be transformed to non-rotating load to predict fuselage vibration. Vibration level was predicted at each forward flight condition by calculating cockpit's vertical acceleration transferred from non-rotating hub load assuming a fuselage as a rigid body. This design method is applied to design current Next-generation Rotor System Blade(NRSB) and will be applied to New Rotor which will be developed Further.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.7
• /
• pp.634-641
• /
• 2009

In this work, the behavior of vibratory hub loads induced due to the uncertainties of composite material properties for each of the participating rotor blades is investigated. The random material properties of composites available from the existing experimental data are processed by using the Monte-Carlo simulation technique to obtain the stochastic distribution of sectional stiffnesses of composite blades. The coefficients of variation (standard deviation divided by the mean) obtained from the sectional stiffness constants are used as an input to the comprehensive aeroelastic analysis code that can evaluate the hub loads of a rotor system. It is found that the uncertainty effects of composite material properties inevitably bring a dissimilarity to the rotor system. The influence of hub vibration response with respect to the individual stiffness (flatwise bending, chordwise bending and torsion) changes is also identified.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.7
• /
• pp.575-582
• /
• 2018

The spaceborne cooler is applied to cool down of the focal plane of the infrared detector of the observation satellite. However, this cooler induces unnecessary micro-jitter which can degrade the image quality of the high-resolution observation satellite. In this study, we proposed a multi-layered blade type vibration isolator to attenuate micro-vibration generated from a spaceborne cooler, while assuring structural safety of the cooler under severe launch loads without an additional launch-lock device. The blade of the isolator is formed with multi-layers in order to obtain durability against fatigue failure and an adhesive is applied between each layers for granting high damping capability under launch vibration environment. In this study, the basic characteristics of the isolator were measured using the free-vibration test. The effectiveness of the isolator design was demonstrated by launch vibration test at qualification level.

• Journal of KSNVE
• /
• v.8 no.5
• /
• pp.765-774
• /
• 1998