• Proceedings of the KSR Conference
• /
• 2002.10b
• /
• pp.820-825
• /
• 2002

As the speed of rail transit is higher, it is very important to secure the safety and confidence of the braking device and in the point of view, by means of the rise of the temperature from the friction between the disk and pad which are the actual part of a braking system, the damage of brake disk is the main cause to lose the safety of braking device. Therefore, in this study, to predict the danger of a disk brake and to know its max. temperature in the train service the module of a temperature measurement by the non-contact method was developed.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.11a
• /
• pp.147-152
• /
• 2000

This paper presents the thermoelastic analysis and 3-D failure analysis of the carbon/carbon brake disk. The mechanical properties of the carbon/carbon brake disk were measured for both in-plane and out of plane directions. The mechanical properties were used as the input of the thermoelastic analysis and 3-D stress analysis for the brake disk. The gap between rotor clip and clip retainer was an important parameter in the loading transfer mechanism of the rotor. The change of gap was considered separating the mechanical deformation and thermal deformation. Because the rotor clip and clip retainers were not contacted, the clip retainers and rivets were excluded from the rotor analysis model. The disk was modeled by using the cyclic symmetry condition and the contact problem between the rotor disk and rotor clip was considered. From the results of the 3-D stress analysis, the stress concentration at the key hole of the brake disk was confirmed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.11
• /
• pp.1692-1696
• /
• 2004

This paper presents the thermally induced hot spot characteristics of rubbing surface in the friction pad disk brake. During the braking period, the rubbing surface with irregular asperities that are strongly engaged in rough surface, wear, and deformed surface due to a friction heating may produce an irregular distorted geometry of the disk surface. The tribological interactions between the disk and the pads are unstable if the contact stress is severe, in which the irregularity develops the contact pressure distribution, leading eventually to localized contact, high temperature and formation of hot spots. The computed results of contact spots that are simulated using a coupled thermal-mechanical analysis present sinusoidal distortions and localized extrusions of the disk surface, which are strongly related to a hot spot in the practical disk brake.

• Transactions of Materials Processing
• /
• v.17 no.6
• /
• pp.407-411
• /
• 2008

A brake system in automobile is one of the important parts that directly affect the safety of passengers. Particularly, disk brake module is applied to almost all kinds of automobile brake system due to its remarkable braking power and braking distance. In the disk brake module of an automobile, the bolt for tire wheel is assembled to the disk brake hub by interference fit(bolt pressing process). The process induces small deformation whose range is within tens of ${\mu}m$ and this deformation may cause the runout badness of the whole disk brake module, and even braking problems such as judder or squeal phenomena which makes the loss of braking efficiency. In this study, bolt pressing fit into hub was simulated by $ANSYS^{TM}$, a commercial structure analysis program. Also, the aspect and the cause of hub displacement were analyzed and the solution for decreasing runout of hub was proposed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.2
• /
• pp.126-134
• /
• 2007

Although there has been substantial research on the squeal noise for the automotive brake system, robust design issues with respect to control factors equivalent to design variables in optimization, noise factors due to system uncertainties, and signal factors designed to accommodate a user-adjustable setting still need to be addressed. For the purpose, the robust design applied to the disk brake system has been investigated by DOE (Design of Experiments) based Taguchi analysis with dynamic characteristics. The specific goal of this methodology is to identify a design with linear signal-response relationship, and variability minimization. The finite element models of the disk brake assembly have been constructed, and the squeal noise problems have been solved by complex eigenvalue analysis. As the practical robust design to reduce the brake squeal noise, material properties of pad, disk, and backplate, thickness and geometry of pad are selected as control factors, material properties of pad and disk, and the contact stiffness have been considered as noise factors, and friction coefficient between pad and disk is chosen as a signal factor. Through the DOE based robust design, the signal-to-noise ratio and the sensitivity for each orthogonal array experiment have been analyzed. Also, it has been proved that the proposed robust design is effective and adequate to reduce the brake squeal noise.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.2
• /
• pp.160-167
• /
• 2004

A two degree-of-freedom mathematical model is presented to investigate the friction mechanism of a disc brake system. A contact parameter is introduced to describe the coupling between the in-plane and the out-of-plane motions. The model with the contact parameter is considered under the assumption that the out-of-plane motion depends on the friction force along the in-plane motion. In order to describe the relationship between the friction force and the out-of plane motion, the dynamic friction coefficient is considered as a function of both relative velocity and normal farce. Using this friction law, a contact stiffness matrix along the normal direction can be obtained. The out-of-plane motion is then investigated by both the stability analysis and the numerical analysis for various parametric conditions. The results show that the stiffness parameters of the pad and the disc must be controlled at the same time. Also, the numerical analysis shows the existence of limit cycle caused by the effect of intermittent contact stiffness.

• Tribology and Lubricants
• /
• v.23 no.6
• /
• pp.312-317
• /
• 2007

In general, a brake system of axle for heavy duty machine as a wheel excavator makes use of wet-type multiple disk brakes. These disk bakes are very important parts of heavy duty machine because they are advanced in durability and braking power, and can be designed compactly. Thus, we designed and made wet-type multiple disk brakes of axle for the 14ton class wheel excavator to be localization of these imported all. These disk brakes were made a comparative test with the existing disk brakes by the SAE No.2 dynamometer, and the friction characteristics as dynamic and static friction coefficient and wear depth of friction paper were measured.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.89-90
• /
• 2008

This paper studies the effect of pad at initial stage and wear during braking on the dynamic contact pressure distribution. Wear is influenced by variable factor (contact pressure, sliding speed, radius, temperature) during dynamic braking and variation in contact pressure distribution. Many researchers have conducted complex eigenvalue analysis considering wear characteristic with Lim and Ashby wear map. The conventional analysis method is assumed the pad has smooth and flat surfaces. The purpose of this paper is to validate that wear rate induced by braking is considered for the precise squeal prediction. After obtaining pad wear from experiment, it is incorporated with FE model of brake system. Finally, the comparisons in fugitive nature of squeal will be carried out between the complex eigenvalue analysis and noise dynamometer experiment.

• Tribology and Lubricants
• /
• v.22 no.3
• /
• pp.149-154
• /
• 2006

This paper presents the braking friction and wears on the rubbing surfaces of a friction pad-disk brake. In this study, four friction disk specimens are sampled from unused and used disks in which are taken from the disk brake system when the friction induced vibration and noise problems have been occurred during a braking period at a running period of 10,000 km, 20,000 km, and 30,000 km in random. The experimental results indicate that the tribological characteristics of an unused disk brake shows equal and stable as a friction coefficient and temperature distributions during a braking friction/wear test period including a total friction mode from the start to running periods. But the used disk brake shows unstable and uneven friction modes between an outside and inside rubbing surfaces of a disk brake in terms of a friction coefficient and wears. This may lead to a friction induced friction vibration and noise problems of a used disk brake.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.05a
• /
• pp.235-239
• /
• 2002

The objective of the experiment is to investigate the effect of microstructures of gray cast iron oil wear characteristics of automotive disc brakes. Six different gray cast iron rotors were manufactured by changing carbon equivalent and cooling rate. The change of DTV (disc thickness variation) before and after wear tests was measured to examine the wear properties according to the microstructures of gray iron discs since the DTV generation is caused by the circumferential uneven wear. Experimental results showed that the morphology of graphite flake and hardness in gray cast iron were crucially associated with the change of DTV. In particular, the DTV changes of rotor decrease when the length and area fraction of graphite flake in brake rotors increase and hardness of brake discs reduces.