• Journal of the korean Society of Automotive Engineers
• /
• v.13 no.4
• /
• pp.35-42
• /
• 1991

본 연구에서는 말단가스의 온도, 압력 그리고 농도가 변화함에 따라 어떻게 자동점화가 일어나는지를 서술하는 chemical kinetic model에 대하여 서술한다. 먼저 자동점화 현상을 화학적으로 modelling하는데 두가지 다른 접근방식에 대해 서술하고 각각 model의 예측치와 실험치와의 상관관계를 알아본 후, 마지막으로 두 model을 비교하여 본다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.153-156
• /
• 2000

This paper presents an PID type fuzzy based method for nohnear engine idle controller The output is a duty cycle(DC) for driving a idle speed cont개l valve(1SCV). For precise control of SI engine, the CPS sensor and coolant temperature are used. Visual C* language is used to make simulation panel for the fast and precise idle speed control. The dSPACE board and supported Control desk program is used in experiment ta the same purpose as simulation. The experimental results have a good agreement with simulation ones.

• 한국연소학회:학술대회논문집
• /
• 2014.11a
• /
• pp.101-102
• /
• 2014

Rising oil price and environmental problems are causing automotive industry to increase fuel efficiency. Improved fuel efficiency in gasoline engine was made possible by development of DISI gasoline engine. Since fuel is injected inside cylinder directly, in-cylinder temperature can be reduced than multi-port injection engine and this leads to increased compression ratio. However, engine performance is largely dependent on mixture formation process due to in-cylinder fuel injection. Especially for spray guided and air guided DISI gasoline engine, injection direction is important factor to mixture preparation. It is because interaction between intake flow and spray affect fuel-air mixture. Hence, in this study, mixture formation characteristics were analyzed by varying injection direction using KIVA 3V release2 code. Residual gas was considered for assuming combustion. Therefore, initial condition for in-cylinder temperature was set equal to the end state of exhaust stroke of combustion cycle. Since angle between intake air flow direction and spray direction affects fluid flow and evaporation field, mixture distribution was affected by fuel injection direction dominantly.

• Journal of Power System Engineering
• /
• v.12 no.4
• /
• pp.12-17
• /
• 2008

The purpose of this study is to analyse and compare the fuel combustion characteristics between LPG and gasoline on SI engine. Pressures of combustion chamber were measured on the state that engine speed was 2000rpm and BMEP was 2.0bar And we measured pressures of combustion chamber regarding variation of the MBT We could know that the combustion pressure of LPG fuel use engine is appeared lower than that of gasoline fuel use engine. At the lean mixture ratio area we could blow that Ignition timings are pulled very forward, and ignition timing of LPG fuel is advanced to $5\sim12^{\circ}$ CA than gasoline fuel. We learned that the value of coefficient of variation of LPG fuel is higher than gasoline fuel.

• Journal of Power System Engineering
• /
• v.11 no.4
• /
• pp.5-11
• /
• 2007

본 연구는 SI기관 실린더 내의 유동장 변이 과정을 3차원 LDV 측정 기술을 사용하여 흡입과 압축과정 동안 정량적으로 분석하였다. 실험은 헤드에 각각 2개의 흡입밸브와 배기밸브를 갖는 기관이 모터링되는 공회전 상태에서 실시하였다. 지난 30년 동안 텀블과 스월은 실린더 내의 평균 유동 정량화에, 난류운동에너지는 난류 측정에 많이 사용되어 왔다. 그러나 텀블은 solid body 회전 유동을 비교하는데 적절하며, 서로 다른 유동 패턴 비교에는 부적절 하다는 것이 보고되고 있는 실정이다. 3차원 LDV시스템의 우수한 공간 분석 능력은 순간적인 유동장구조와 더불어 상대적으로 미세한 유동장의 구조 까지도 측정이 가능 하도록 하였다. 따라서 측정한 결과로부터 유동장의 난류운동에너지 등가면을 계산할 수 있었다. 본 실험 결과는 실린더 내의 난류 유동장 특성을 난류운동 에너지 등가면 정보를 이용하여 세심하게 관찰할 수 있음을 제시하고 있다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.1 no.1
• /
• pp.80-89
• /
• 1993

Performance simulation for a Spark Ignition Wankel rotary Engine is presented in this paper. The volume of chamber at each eccentric shaft angle is evaluated by using geometric models of housing and rotor. A thermodynamic model which includes the first law of thermodynamics, combustion and convective heat transfer from chamber contents to surroundings is imployed. A thermochemical equilibrium model which considers 10 species(CO, $CO_2$, $O_2$, $H_2$, $H_2O$, OH, O, NO, $N_2$) in the burned gas region, is also employed. Four processes of gas exchange, compression, combustion and expansion are considered and the pressure, temperature and composition of chamber gas at each eccentric shaft angle in each process are computed in this performance simulation. This performance simulation must be useful for optimal design of Spark Ignition Wankel Rotray Engine with parametric study for various design parameters and operating conditions.

• Fire Science and Engineering
• /
• v.30 no.5
• /
• pp.1-8
• /
• 2016

Safety management in hazardous areas with potentially explosive gas atmospheres (here in after referred to as hazardous areas) in large scale facilities dealing with combustible or flammable materials at home and abroad is very important (significant) for the coexistence of the company and local society based on business continuity management (BCM) and reliance. For the safety management in hazardous areas, two systems are mainly used: (1) the control system for the prevention of combustible or flammable substances and (2) the explosion proof system for the elimination of ignition sources when flammable gases are leaked to inhibit the transition to fire or explosion accidents. While technology and regulations on explosion proof facilities or devices for electrical ignition sources are well developed and defined, those for thermal ignition sources need to be more developed and established. In this study, the internal combustion engine in hazardous areas was investigated to determine the risk of ignition. For this purpose, document searches were conducted on the relevant international standards and accidents cases and risk analysis reports. In addition, this study assessed the application cases of the diesel engine's safety equipment, such as spark arresters regarding the site of process safety management (PSM) system in central Korea. To practically apply these results to the hydrocarbon industry, the safety management method for explosion prevention in hazardous areas was provided by risk identification for ignition sources of internal combustion engines, such as diesel engines.

• Journal of Energy Engineering
• /
• v.11 no.1
• /
• pp.74-80
• /
• 2002

In this study, a numerical method for fuel droplet evaporation in cylinder of S.I. engine is presented. This study was newly defined non-dimensional critical droplet lifetime and modeled heating and evaporation processes of fuel droplet during intake and compression stroke of gasoline engine. The simulation results show that simultaneous increase of gas temperature and pressure in compression stroke seems to have compensative effect on droplet gasification rate. The environment variations in cylinder have little effect on the fuel droplet gasification process. The droplet size for full evaporation at the end of compression stroke can be estimated using this program.

• Journal of Power System Engineering
• /
• v.3 no.2
• /
• pp.20-25
• /
• 1999

Experiments were carried out to investigate the characteristics of formaldehyde emission from the small gasoline engine and its reduction technologies. Catalytic converters used are Pt/Rh, Pd/Rh, Pd/Pt, $62cell/cm^2$ monolith type. The measurement of formaldehyde was conducted by using the method of DNPH-GC. From the experimental results, formaldehyde emission increased in a lean mixture due to incomplete combustion of the hydrocarbons. The order of catalytic activity of formaldehyde oxidation was Pt/Rh > Pd/Rh > Pd/Pt. As the distance from the exhaust manifold to the inlet of the catalyst became far, in spite of lower catalyst temperature, formaldehyde concentration decreased because of the adsorption of formaldehyde.

• Journal of the Korean Institute of Gas
• /
• v.12 no.3
• /
• pp.7-12
• /
• 2008

In this study, a spark ignition engine operated with the DME blended LPG fuel was investigated experimentally. Performance, emissions characteristics including hydrocarbon, CO, NOx, and combustion stability of an SI engine fuelled with DME blended LPG fuel were examined at $1200{\sim}5200\;rpm$. Results showed that stable engine operation was possible for a wide range of engine loads within 20% mass content of DME fuel. Also, engine output power within 10% mass content of DME fuel was comparable to that of pure LPG fuel operation. However, engine output power was decreased and break specific fuel consumption (BSFC) was severely increased with the amount of blended fuel as the energy content of DME was much lower than that of LPG. DME blended LPG fuel is expected to be potential for enlarging DME market.