• Resources Recycling
• /
• v.30 no.5
• /
• pp.57-66
• /
• 2021

In this study, we attempted to separate and recover Cu from low-grade copper ore by a hydrometallurgical process. The leaching sample obtained after crushing and sieving by 0.355 mm of low-grade copper ore contained 1.5% Cu, 4.7% Fe, 1.0% Mn, and 0.3% Zn. The Cu in the oxide ore was very well leached into sulfuric acid and 97% Cu leaching efficiency was achieved at 80℃ and 3 M sulfuric acid (H₂SO₄). From the leaching solution, Cu was separated by solvent extraction from Fe, Mn, and Zn using LIX984N. The separation tendency between Cu and other metals was confirmed through the distribution ratio and separation factor. By plotting the McCabe-Thiele Diagram, the optimum condition for recovering Cu is 5 vol.% LIX984N, 2-stage counter-current solvent extraction, and an O/A ratio of 0.5. Using this method, 99% of the Cu was extracted and a CuSO₄ solution was finally obtained that contained 1.6 g/L Cu after the stripping process using 2 M H₂SO₄.

• Journal of Korean Society of Forest Science
• /
• v.100 no.2
• /
• pp.136-141
• /
• 2011

This study was conducted to confirm the application as ingredients of cosmetics through an examination of the function for anti-cancer and anti-microbial of the fraction isolated from Pyrus ussuriensis leaves. The dried leaf of P. ussuriensis were extracted with acetone-$H_{2}O$ (6:4, v/v), concentrated and fractionated with the upper layer of acetone on a separatory funnel. Each fraction was freeze dried, then a portion of acetone soluble powder was chromatographed on a Sephadex LH-20 column using a series of aqueous methanol as eluents and also used the MIC-gel using a series of aqueous methanol as developing solvent. The isolated compounds were identified by silica-gel TLC. The growth inhibition activity was measured using the MTT assay by the mouse meltioma (B16F10) cell. The cancer cell growth inhibition rate of fractions isolated from P. ussuriensis leaf was 80%. In anti-microbial activity test, the fraction of P. ussuriensis with 0.25 mg/disc resulted in the clear zone of 1.3 cm and 2 cm for Staphylococcus aureus and S. epidermidis of gram positive bacillus, respectively. In Escherichia coli of gram negative bacillus, the fraction with 0.5 mg/disc resulted in the clear zone of 1.1 cm~1.5 cm each fraction. From these results, we confirmed that acetate fraction of P. ussuriensis has a great potential as a natural ingredients with a anti-cancer and anti-microbial source.

• Information Display
• /
• v.23 no.4
• /
• pp.12-21
• /
• 2022

반도체 기반 양자점 (QD)소재와 CsPbX3 (X=Cl, Br, I)기반 perovskite 양자점 또는 나노결정 소재(PNC)는 매우 우수한 양자효율과 좁은 발광 선폭으로 고색재현성 디스플레이 색변환 소재 또는 발광 소재로서 각광을 받고 있다. 그러나, 기존 화학적 합성법을 통해 제조되는 QD 및 PNC 소재는 취약한 열 및 화학적 안정성으로 인해 장기 내구성의 개선이 요구된다. 이들 QD 및 PNC 소재는 모두 완전 무기 소재인 산화물 기반 유리 소재내에 생성이 가능하며, 이를 통해 장기 내구성을 근본적으로 개선할 수 있다. 반도체 기반 QD 함유 유리소재 (QDEG)의 경우, 유리 내 core/shell 구조를 가진 QD의 생성으로 양자효율의 향상이 가능했으나, 콜로이드 기반 양자점 (cQD)과 달리 다중 shell의 형성이 어려워 양자효율이 제한되고, 발광 선폭이 넓어 고색재현성 디스플레이용 색변환 소재로 적용되기에는 아직 한계가 있다. 한편, Perovskite 양자점 (또는 나노결정) 함유 유리소재 (PNEG) 소재는 QDEG과 달리 콜로이드 기반의 PNC (c-PNC)가 가지는 우수한 양자효율과 20 nm 수준의 좁은 선폭을 유리 내에서도 가지며, c-PNC 대비 열적, 화학적 및 광학적 안정성이 획기적으로 향상되어 실질적인 응용 가능성을 높이고 있다. 특히, 일반적인 용융-급랭법으로 제조하여 대량생산에 용이하고, 분말 또는 판상 등 다양한 형태로의 제작이 가능한 장점이 있다. 현재까지 제조된 PNEG의 최대 PL-QY는 450 nm 여기 시 녹색 및 적색에서 약 60% 수준이며, Al₂O₃ 분말을 이용할 경우 최대 80% 수준까지 달성이 가능하다. 또한, PNEG과 blue LED를 이용하여 백색 LED를 구현할 경우 color filter를 적용하지 않을 때, NTSC 대비 최대 약 130 % 수준의 높은 색재현 영역을 보여 주고 있으며, 실제 LCD용 BLU로 적용 시 기존 상용 c-QD 소재와 동등 이상의 색재현 영역을 보이고 있어, 실질적인 응용 가능성이 매우 높음을 확인하였다. PNEG의 상업적인 응용을 위해서는 몇 가지 추가적인 연구 개발이 필요하다. 기존 c-QD 또는 c-PNC는 나노 수준 크기의 입자가 액상에 분산된 형태로 입도 제어가 용이하나, PNEG의 경우 분말 제조 시 유리 형성 후 분쇄를 통해 제조되며, 입도가 대개 수십 ㎛ 이하로 작아질 경우 PL-QY가 저하되어, 향후 잉크젯 공정 응용을 위해서는 고효율의 분말 제조공정 개발이 필요하다. 또한, 유리 소재의 경우 절연체로서 기존 QD 소재 대비 electro-luminescence(EL) 소자의 활성층으로 사용하는데 제약이 있어 PNEG을 이용한 EL 소자 제작에 대한 연구도 필요하다. 마지막으로, 기존 c-PNC 소재와 같이 Pb가 함유되지 않은 PNEG 소재의 개발이 선결되어야 할 것으로 판단된다. 이와 같은 해결 과제들에도 불구하고, PNEG 소재는 기존 c-QD 소재 대비 매우 우수한 안정성을 기반으로 고품위 고색재현 디스플레이용 색변환 소재로서 다양한 응용에 활용될 수 있을 것으로 기대된다.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.8 no.2
• /
• pp.130-139
• /
• 2000

Serial basic tests were conducted for the determination of fundamental kinetics and for the actual application of kinetic parameter to food waste digestion with precise measurement of methane production under a thermophilic condition. The effects of food particle size, sodium ion concentration, and volatile solid (VS) loading rate on the anaerobic thermophilic food waste digestion process were investigated. Results of serial test for the determination of fundamental kinetic coefficients showed the value of k (maximum substrate utilization rate coefficient) and KS (half-saturation coefficient) as $0.24hr^{-1}$ and $700mg/{\ell}$, respectively, for non-inhibiting organic loading range. No inhibition effect was shown until $5g/{\ell}$ of sodium ion concentration was applied to a serum bottle reactor. However, the volume of methane gas was decreased gradually when the concentrations of more than $5g/{\ell}$ of sodium ion applied. All sizes of food waste particle showed the same constants (A : 0.45) but the maximum substrate utilization rate constant ($k_{HA}$) was inversely proportional to particle size. As an average particle size increased from 1.02 mm to 2.14 mm, $k_{HA}$ decreased from $0.0033hr^{-1}$ to $0.0015hr^{-1}$. The result reveals that particle size is one of the most important factors in anaerobic food waste digestion. There was no inhibition effect of sodium ion when VS loading rate was $30g/{\ell}$. And maximum injection concentration of VS loading rate was determined about $40g/{\ell}$.

• Applied Biological Chemistry
• /
• v.36 no.4
• /
• pp.271-276
• /
• 1993

This study was carried out to prepare anchovy based powder for instant soup packed in tea bag which can be used handily as a extractives, and to determine the taste compounds of extractives of anchovy based powder for instant soup. The anchovy based powder for instant soup was made by adding of 72% in the redried anchovy, 14% in the sea tangle, 7% in the mushroom and 7% in the katsuobushi to the total mixtures. And the anchovy based powder for instant soup was packed in tea bag. The desirable extraction time are 5 min in package in tea bag with air permeability $100\;m^3/m^2/min$ and over 20 min in package in tea bag with air permeability $65\;m^3/m^2/min$, respectively. Judging from the result of extraction rate of total nitrogen, color and sensory evaluation in extractives of anchovy based powder for instant soup extracted by optimal extraction time, the quality in extractives of instant soup packed in tea bag with air permeability $100\;m^3/m^2/min$ was superior to those of instant soup unpacked in tea bag and of instant soup packed in tea bag of air permeability $65\;m^3/m^2/min$. The principal taste compounds of extractives of anchovy based powder for instant soup packed in tea bag with air permeability $100\;m^3/m^2/min$ were IMP (9.26 mg/100ml in 5% solution) and free amino acids (24.30 mg/100 ml in 5% solution) such as histidine, proline, lysine and taurine. Total creatinine, betaine and TMAO were seemed to act an auxiliary role in taste of extracives of anchovy based powder for instant soup packed in tea bag with air permeability $100\;m^3/m^2/min$.

• Journal of Bio-Environment Control
• /
• v.4 no.1
• /
• pp.50-58
• /
• 1995

These studies were carried out to develop a system for non -destructive and continuous measurement of fresh weight and to analyse the growth response of leaf lettuce under the different nutrient solution and light condition with this system. The developed measurement system was consisted of four load cells and a microcomputer. The output from the system was highly positive correlation with the plant fresh weight above the surface of the hydroponic solution. The top fresh weight of plant could be measured within the error $\pm$ 1.0g in the range of 0 - 2000g. The top fresh weight of leaf lettuce increased 44 times at 18th day after transferring to the nutrient solution, and the maximum growth rate was observed at 13th day after transferring. The growth rate was 10.7- 29.6% per day during 18 days. Optimum concentration of the nutrient solution for the growth of lettuce was 1.4 - 2.2 mS/cm of EC level. When the light condition was changed from dark to light, the fresh weight was temporarily decreased, but the fresh weight increased under the opposite condition. Top fresh weight of leaf lettuce in the darkness normally increased within 12 hours after darkness treatment, and then slowly increased until 78 hours under continuous dark condition. After that times, the fresh weight began to decrease.

• Journal of Bio-Environment Control
• /
• v.7 no.1
• /
• pp.63-70
• /
• 1998

This study was carried out to investigate the interaction of selenate and sulfate ion in nutrient solution supplyed with selenate ion. At early growth stage, the growth of Mongolian wormwood was best at 3mM sulfate ion and 2mg/$\ell$Na$_2$SeO$_4$ treatment. As they were grown and matured, at the later growth stage, the effect of antagonism between selenate and sulfate ion on the growth of each plant decreased. At supplying with selenate ion in nutrient solution, the uptake of selenate by plant had negative correlation with sulfate ion concentration in nutrient solution. The higher sulfate ion concentration, the less selenium uptake. However, the effect of antagonistic interaction of selenate and sulfate ion on the selenium uptake increased with plant age. Whereas, the uptake of sulfate ion had positive correlation with sulfate ion concentration in nutrient solution at supplying with selenate ion in nutrient solution. The uptake of sulfate ion increased with increase of sulfate ion concentration in nutrient solution. The effect of this interaction with selenate and sulfate ion increased with growth and maturity of plant. However, at 3mM sulfate ion concentration in nutrient solution, sulfate ion concentration in plant tissue decreased markedly.

• Journal of Ginseng Research
• /
• v.32 no.3
• /
• pp.179-186
• /
• 2008

Effect of pulverization on total solid, crude saponin, and acidic polysaccharide contents of dried red ginseng main root were tested. Several particle size samples, including red ginseng main root (non pulverized), $10{\sim}40$ mesh powder, $40{\sim}100$ mesh powder, and >100 mesh powder were used in the extraction. The sequential solvent extraction method (1st: 70% EtOH at $70^{\circ}C$ for 12 hr, 2nd: 70% EtOH at $70^{\circ}C$ for 12 hr, 3rd: water at $70^{\circ}C$ for 12 hr) was applied to extract the saponins and acidic polysaccharide. Extraction yield of total solid of pulverized red ginseng ($10{\sim}40$ mesh size) was increased to 20% compared with that of non-pulverized. Especially, the crude saponin content of pulverized red ginseng ($10{\sim}40$ mesh size) showed an increase of 47% over non-pulverized. No difference in the component ratio was observed by pulverization, when the individual ginsenosides were quantified by HPLC. Also, extraction yield of acidic polysaccharide of pulverized red ginseng ($10{\sim}40$ mesh size) was increased 57% compared with that of non-pulverized. The results suggested that pulverization might be useful for increasing the extraction yield of red ginseng components.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.7
• /
• pp.504-509
• /
• 2018

The purpose of this study was to manufacture a high-performance titanium yellow pigment. Anatase type $TiO_2$ was the skeleton of the pigment and $Sb_2O_3$ is used as the color assistant for the coloring agent, $Cr_2O_3$. Mixed raw materials for the pigment were $TiO_2$(98%), $Sb_2O_3$(99.5%), and $Cr_2O_3$(99.5%). The raw materials were mixed by a dry process and crystallized by calcination at $1,000{\sim}1,200^{\circ}C$. The crystalline material was pulverized in a Jar Mill under $1{\mu}m$ by a wet process and dried for 12 hours at $100^{\circ}C$. The pigment was finally made by a fine grinding process. To determine the best temperature for calcination, 4 temperature sections ($1000^{\circ}C$, $1100^{\circ}C$, $1150^{\circ}C$, and $1200^{\circ}C$) were set up. The X-ray diffraction peak of the rutile crystalline structure was highest at $1,150^{\circ}C$. The yellow ceramic pigment, which has the rutile structure, was applied for coating materials. The synthesized pigments underwent a discoloration tests on the acid resistance, alkaline resistance, weather resistance and heat resistance. In addition, a detection test on harmful heavy metals ($Cr^{+6}$) was done. The resulting values (${\Delta}E$) of the weather resistance test (2000hr), acid resistance test, alkaline resistance test, and heat resistance test were 0.74, 0.16, 0.07 and 0.29. The resulting value for heavy metals testing was 34ppm.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.7
• /
• pp.514-520
• /
• 2014

In this study, the production potential of alternative coagulant ($Al_2(SO_4)_3$ solution) having the identical coagulation activity with respect to the commercial coagulant was investigated. The raw material of alternative coagulant was a spent catalyst including aluminium (waste activated alumina) generated in the manufacturing process of the polymer. The alternative coagulant was produced through a series of processes: 1) intense heat and grinding, 2) chemical polymerization and substitution with $H_2SO_4$ solution, 3) dissolution and dilution and 4) settling and separation. To determine the optimal operating conditions in the lab-scale autoclave and dissolver, the content of $Al_2O_3$ in alternative coagulant was analyzed according to changes of the purity of sulfuric acid, reaction temperature, injection ratio of sulfuric acid and water in the dissolver. The results showed that the alternative coagulant having the $Al_2O_3$ content of 7~8% was produced under the optimal conditions such as $H_2SO_4$ purity of 50%, reaction temperature of $120^{\circ}C$, injection ratio of $H_2SO_4$ of 5 times and injection ratio of water of 2.3 times in dissolver. In order to evaluate the coagulation activity of the alternative coagulant, the Jar-test was conducted to the effluent in aerobic reactor. As a result, in both cases of Al/P mole of 1.5 and 2.0, the coagulation activity of the alternative coagulant was higher than that of the existing commercial coagulant. When the production costs were compared between the alternative and commercial coagulant through economic analysis, the production cost reduction of about 50% was available in the case of the alternative coagulant. In addition, it was identified that the alternative coagulant could be applied at field wastewater treatment plant without environmental problem through ecological toxicity testing.