• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.11
• /
• pp.83-89
• /
• 2008

The Effect of Space Velocity(SV) on NOx conversion rate was performed to develop NOx reduction after-treatment system. SV is calculated from engine exhaust gas volume and SCR catalyst volume. Found the Urea injection duty of maximum efficiency for NOx conversion if increase SV, NOx Conversion rate is down. Especially, when SV is more than $110,000h^{-1}$, NOx conversion rate decrease suddenly. Same case, if SV is lower than $40,000h^{-1}$, NOx conversion rate is down. Also, the characterization of Urea-SCR system was performed. Three candidate injectors for injecting Urea were tested in terms of 속 injection rate and NOx reduction rate. The performances of SCR catalytic converter on temperature were investigated. The performance of Urea-SCR system was estimated in the NEDC test cycle with and without EGR. It was found that nozzle type injector had high NOx conversion rate. SCR catalytic converter had the highest efficiency at the temperature of $350^{\circ}C$. EGR+Urea-SCR system achieved NOx reduction efficiency of 73% through the NEDC test cycle.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.4
• /
• pp.154-162
• /
• 2004

In this study, a mathematical model for analyzing the shifting transients of the passenger car with an automatic transmission is proposed. The proposed model comprises a power transmission system and a vehicle system, which are coupled. In order to extract the modeling parameters, on-road car test is carried out. The model is composed of a detailed powertrain, an engine/AT housing, a simplified suspension system, tires and a vehicle body model. On the test, the vehicle accelerations and pitch ratio are measured by using accelerometers and a gyro sensor. The speeds, the brake signal, and the throttle position are taken from sensors which already exist in the vehicle. Considering natural ftequencies, which is calculated from the measured accelerations, and the characteristic equation, vehicle model parameters are identified. Dynamic behaviors during upshift or downshift are simulated using the proposed vehicle model. By comparing and analyzing the simulation result and on-road car test data, the vibration of the Engine/AT housing influences the shifting transients. The effect of model parameters are also studied. Among model parameters, the location of engine mountings influences the vibration of the vehicle body.

• Journal of the korean Society of Automotive Engineers
• /
• v.8 no.4
• /
• pp.24-35
• /
• 1986

현재 주요 가스상물질은 미국의 경우 규제전보다 일산화탄소가 96%, 탄화수소 96%, 질소산화물 76%가 개선되어 어느정도 안정단계에 들어 갔다고 볼 수 있다. 그러나, 입자상물질규제는 디이 젤자동차의 증가와 더불어 1986-1994기간동안 대폭적으로 강화되고 있다. 그러나 자동차 배출 가스중에는 수백가지의 화학물질이 존재하고 인체에 유독한 물질은 규제물질외에도 엄청나게 많다. 따라서 1977년 8월에 개정된 미국의 대기정정법(CAA, clean air act)에는 "신규 제작자동 차나 엔진에 사용되는 어떠한 방지장치, 시스템 또는 부품도 공중보건, 복지 및 안전에 부당한 위험을 일으키거나 일으키는 요인이 될 수 없다"(참조, CAA 202 (a) 및 CFR 86.084-5)고 규 정하고 있다. 이에 따라 미국환경청에서는 회람 등을 통하여 가능한 독성물질에 대하여 경우에 따라 측정할 것을 요구하고 있다. 국내 환경보전법에도 자동차연료첨가제 사용할 때 현저하게 유해한 물질이 배출된다고 인정하는 때에는 그 사용을 규제할 수 있게 되어있고 새로 제정될 자동차 배출가스 시험검사방법 및 절차에 관한 규정에 이에 관한 사항을 추가할 움직임이 있다. 물론 미규제물질의 규제하는 인체에 대한 피해정도나 측정방법 등의 여러 가지 문제가 수반되나 장기적인 국민보건과 환경보전 측면에서 신중하게 다루어져야 되리라 봐서 여러 가지 오염물질의 현황이나 분석방법 등에 대하여 기술코자 한다.여 기술코자 한다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.254-254
• /
• 2012

최근 친환경 에너지원 및 에너지 저감기술을 바탕으로 한 자동차 부품산업이 재편되고 있다. 그 중, 극한의 산화전해질 환경에서 견뎌야하는 연료전지 분리막 소재와, 자동차 연비향상을 위한 엔진소재 개발 경쟁이 가열되는 상황이다. 이러한 소재에는 공통적으로 고 내식성과 내 마모성의 특성이 요구되는데, 스테인레스강은 이러한 조건에 적합한 소재이다. 왜냐하면, 사용분위기에 의해 산화막이 두꺼워지고 이로 인해 저항이 증가하는 현상 때문에 연료전지 부품에 질화를 하여 이런한 현상이 일어나지 않으면서 내식성은 유지하기 때문이다. 하지만, 표면경도가 낮아 내 마모성 저하로 부품의 수명을 떨어뜨리는 단점이 있다. 따라서, 고 내식성 유지하되, 표면경도는 향상하는 기술이 필요한데, S-phase 과고용 질화기술은 이러한 문제를 해결할 것으로 보여진다. 하지만, 이러한 층의 형성에도 불구하고, 스테인레스강 자체 소재제작 과정에서의 품질문제 및 가공경화로 인한 문제와 더불어 질화처리 후 표면계질의 석출상이나 크랙형성으로 인해 내식성은 오히려 저감되는 문제를 지니고 있다. 이에 대한 대안으로, 표면 질화처리 후 침탄 공정을 추가 도입하였다. 따라서, 본 연구 에서는 기존 질화공정에서 내식성 저하원인에 대한 분석 및 고찰하고, 또한 새롭게 제안된 질화 침탄 기술을 통해 질소뿐만 아니라 탄소원자의 침입으로 내식성 저하를 방지하는 동시에 표면경도 향상하는 새로운 연구결과를 보여주고자 한다.

• Journal of Biosystems Engineering
• /
• v.28 no.1
• /
• pp.27-34
• /
• 2003

Present combustion engines have reached almost at the limit of development due to the fundamental structural problems. This study was carried out to propose a new concept internal combustion engine which has great potential advantages to the conventional engines. Proposed new concept engine is a kind of rotary engine. A rotor is rotating concentrically in a cylinder which is divided into two partitioning valves. and it makes four compartments in the cylinder. The volumes of each of four compartments are changing continuously with the rotor movement, and performs the functions of intake, compression. expansion and exhaust simultaneously. The results of this study can be summarized as follows. 1. Expected theoretical thermal efficiency is 44.9 percent at the condition of 1000rpm and compression ratio of 8.0. which is almost the same as that of the conventional engines. i.e., piston and Wankel rotary engine. 2. The new concept engine has 2. working strokes in every revolution. Therefore. the new concept engine can reduce the specific weight and volume than four-stroke piston engine. 3. The torque variation is very small. therefore minimal noise and vibration are expectable. 4. The new concept engine can reduce mechanical energy loss than piston engine because neither crank mechanism nor eccentrical motion exists.

• Journal of Biosystems Engineering
• /
• v.30 no.6 s.113
• /
• pp.354-359
• /
• 2005

This is a fundamental study to develop a bio-gas utilization technology using livestock manure. Especially, this study was carried out to develop an engine using bio-gas. A bio-gas engine was designed and manufactured by modification of a diesel engine of 3 cylinders powering 13.31 kW/2800 rpm, changing the fuel supplying system fit for bio-gas. The result showed that, when the Air/Fuel ratio was controlled with fixed spark timing, the power of biogas-fueled engine is about $10.6{\~}14.6\%$ lower then that of LNG-fueled engine because of low volumetric efficiency. The engine output and torque was $11.85{\~}13.3$ kW, $39.5{\~}40.8\;N{\cdot}m$, respectively at the engine speed of 2600 rpm. Bio-gas consumption rate was 260.20 g/kW/hr, 315.20 g/kW/hr in engine speed or 1000 rpm, 2800 rpm, respectively.

• Journal of Internet Computing and Services
• /
• v.11 no.4
• /
• pp.85-94
• /
• 2010

In this paper, we propose a location-prediction structure that can provide user service in advance. It consists of seven steps and supplies intelligent services which can forecast user's location. Context information collected from physical sensors and a history database is so difficult that it can't present importance of data and abstraction of data because of heterogeneous data type. Hence, we offer the location-prediction that change data type from heterogeneous data to homogeneous data. Extracted data is clustered by SOFM, then it gets user's location information by ARIMA and realizes the services by a reasoning engine. In order to validate the proposed location-prediction, we built a test-bed and test it by the scenario.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.5
• /
• pp.151-156
• /
• 2013

The experiment was done on cars travelling at the speeds of 20km/h, 60km/h and 100km/h using the performance testing mode for chassis dynamometer. In this experiment, the relativity between the secondary waveform coming from ignition coil and exhaust emissions were measured in case of cars with failures, in oxygen sensor, spark plugs. The following results obtained by analysis of the relativity between the secondary waveform and exhaust emissions. 1) When the oxygen sensor is failure, the average value of CO emission measured was 6.8 times higher than the standard CO emission value and the average value of HC emission measured was 2.3 times higher than the standard emission level. 2) When engine parts are in failure, more fuel enters the cylinder due to longer opening duration of injector, and it tended to make CO and HC emission values increase. 3) Combustion duration, the shape of flame propagation during spark line, and the size of the discharge-induced energy were the three main elements that directly cause variations in CO and HC emission values.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.04a
• /
• pp.152-156
• /
• 2007

It is very important to understand about mass flow rate variations of propellants generated by pressure fluctuation in the combustion chamber. Therefore, we have studied quantifying the variation of mass flow rate generated by pressure fluctuation. The flow velocity in orifice is acquired through theoretical approach after measuring the pressure in orifice and the flow area in orifice is measured by film thickness measuring device. Our results agreed with it in the very small error range comparing our results with velocity and mass flow rate in steady state. Thus, our result based on theoretical approach will help about measuring mass flow rate in non-steady state.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.3
• /
• pp.34-39
• /
• 2014

A study is analyzed on the design factor of center-body diffuser and performed on conceptual design of center-body diffuser with computational fluid dynamic. The flow field of center-body diffuser is calculated using axisymmetric two-dimensional Navier-Stokes equation with $k-{\epsilon}$ turbulencemodel. The center-body diffuser is compared with second throat exhaust diffuser in terms of starting pressure, the degree of vacuum pressure and the design factors. The counter flow jet on cone-tip of the center-body is applied for thermal protection system in the center-body diffuser.