• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.3
• /
• pp.41-48
• /
• 2017

The combustion characteristics of gaseous methane-gaseous oxygen, an eco-friendly bipropellant injected by shear coaxial injector, were investigated. Flame was photographed under various combustion conditions using a DSLR camera, and the characteristics of the flame shape was quantified by image post-processing. From the view point of stabilization, the diffusion flame could be divided into anchored flame regime and blow-off regime. As the oxidizer Reynolds number ($Re_o$) increased, a probability of the formation of anchored flame increased with the length of flame. The shear coaxial injector used in this experiment was found to require a large length-to-diameter ratio of combustion chamber because it formed a relatively long flame in the injection direction due to a poor mixing depending only on the momentum diffusion of two propellant jets.

• Journal of the Korean Institute of Gas
• /
• v.16 no.3
• /
• pp.48-53
• /
• 2012

The purpose of this paper studies the failure cases including with system of liquefied phase injection in liquified petroleum gas vehicle. The first case, resulting with inspection the injector of LPG, it occasionally certified the injection damage phenomenon that the fuel efficiency(km/l) was decreased to 5% by carbon deposit with injector hole when the driver operates the vehicle. The second case, it certified the interference phenomenon of air flow with carbon deposit in ISA system control for idle speed of engine and throttle body suppling air into engine. As a result, the fuel efficiency was decreased 7%. The third case, the outer air during intake stroke was intermittently flowed in this gasket gap because of weaken adhesion power phenomenon for cylinder block by intake manifold gasket tearing. Consequentially, it certified the decrease for fuel efficiency to 3% by risen the amount of fuel injection as the air inflow quantity. These failure examples reduced the power performance of engine and the fuel efficiency of vehicle. It have to minimize of failure phenomenon preparing through quality management.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.1
• /
• pp.17-25
• /
• 2017

An experimental study was performed for the combustion-field visualization of the burner which burns the liquid hydrocarbon fuel atomized by an ultrasonic oscillator. Configurations of the flame and temperature gradient were caught by both high-speed camera and thermo-graphic camera, and those images were analyzed in detail through a post-processing. In addition, the fuel consumption was measured using the balance during the combustion reaction. As a result, the consumption of atomized fuel increased with the increasing flow-rate of carrier-gas, but any correlation between the air/fuel ratio and carrier-gas flow-rate was not found at the low flow-rate condition. Also, the combustion-field grew and reaction-temperature rose due to the strengthening of combustion reaction with the increasing flow-rate of carrier-gas and power consumption of ultrasonic oscillator.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.05a
• /
• pp.391-394
• /
• 2012

Recently, for appling to industrial engines to CRDI diesel engine to meet enhanced emission regulatory standards in native and foreign, ECU that be controlled only automaker develop engine control algorithm that adjust injection timing and injection as user's need and use testing, verification for engine performance and emissions reduction. For development only CRDI diesel engine emulator, using CKP and CMP sensor performance property of CRDI engine control ECU input element, in this paper, there determine the diesel knocking and propose design methodology of engine balance correction algorithm design of the correction algorithm. And there propose efficient Improvement for fuel efficiency increasing and reduction of emissions.

• Journal of ILASS-Korea
• /
• v.25 no.3
• /
• pp.95-102
• /
• 2020

Six shear coaxial injectors for a 3 tonf-class liquid rocket engine using oxygen and methane as propellants were designed and manufactured by considering geometric design parameters such as a recess length and a taper angle. Cold-flow tests on the injectors were performed using water and air as simulants. By changing the water mass flow rate and air mass flow rate, the injection pressure drop under single-injection and bi-injection was measured. The discharge coefficients through the injector oxidizer-side and fuel-side were calculated and the discharge coefficient ratio between bi-injection and single-injection was obtained. Under single-injection, the recess served to reduce the injection pressure drop on the injector fuel-side. For the injectors without recess, the discharge coefficients under bi-injection were almost the same as those under single-injection. However, for the injectors with recess, the taper angle and bi-injection had a significant effect on the discharge coefficient.

• Journal of ILASS-Korea
• /
• v.16 no.1
• /
• pp.44-50
• /
• 2011

An object of this study is to understand the correlation of injection characteristics and injector dimensions according to biodiesel mixture. The Injection characteristics of different types of common-rail injectors are the number of nozzle holes (5~8), jet cone angle ($146^{\circ}{\sim}153^{\circ}$), hydraulic flow rate (830~900 ml/min) injection quantity and response time. Prior to characteristic experiment, the reference injector has been selected in 6 candidates injectors under the investigation of injected quantity according to the biodiesel mixture so that injector type can be determined. The injector is used for the characteristic experiment which varied the various operating conditions including pressure 23 MPa, 80 MPa, 160 MPa, changing in injection duration 0.16 ms~1.2 ms and even mixture ratio. The result shows that the nozzle hole number and cone angle influence the injection quantity much more than nozzle hole diameter at low injection pressure and the nozzle hole diameter at high injection pressure, post injection duration.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.149-152
• /
• 2009

Spray characteristic parameters such as droplet mean velocity, diameter, and volume flux are measured at various locations of spray in order to investigate the evolutionary feature of droplets exiting from a direct-injection type thruster nozzle-orifice. The experimental results indicate that the large droplets with high velocity at the center of upstream are broken-up into smaller droplets with low velocity due to their continuous momentum loss to surrounding air along with spray evolution toward downstream. Also it is found that the high volume flux expands its distribution in radial direction as a results of spray spreading and dispersion.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.99-102
• /
• 2009

LES(Large eddy simulation) of breakup and atomization of a liquid jet into cross turbulent flow was performed. Two phase flow between a gas phase and a liquid phase was modeled by a mixed numerical scheme of both Eulerian and Lagrangian methods for gas and liquid phases respectively. The first and second breakup of liquid column was observed. The penetration depth in cross flow was comparable with experimental data for several variant of a liquid-gas momentum flux ratio by varying liquid injection velocities. SMD(Sauter Mean Diameter) distribution downstream of jet was analyzed.

• Journal of the Korean Ceramic Society
• /
• v.38 no.6
• /
• pp.545-550
• /
• 2001

본 연구에서는 분사연소합성(SCS)을 위한 기초단계로서 용액연소합성에 대한 거동을 살펴보고자 알루미나 합성을 모델로 하였으며 이를 위해 전구체에 대한 열분해거동, 그리고 각 온도에서의 평형종 분압 계산 및 합성과정을 조사하였다. 각각의 열중량 분석(TGA) 결과 산화제와 환원제(연료)의 열분해 이력이 서로 다르게 나타났으며, 열역학 응용 프로그램인 ChemSag에 의한 평형종 분압의 계산에서 연소속도를 저하시킬 수 있는 $CO_2$와 수증기 가스 분압이 상당부분 존재하였다. 산화제/환원제 혼합물의 열분석(DTA/TG) 결과 산화제와 환원제의 열분해 거동의 차이, 그리고 매우 작은 시료의 양으로 인해 263$^{\circ}C$에서 발열피크가 매우 작게 나타났다. 열분석 시료에 비해 발열 에너지를 높이기 위해 산화제와 환원제 혼합 전구체를 비이커에서 증기압을 조절하며 가열시켜 본 결과 27$0^{\circ}C$에서 $\alpha$-Al$_2$O$_3$생성물을 얻을 수 있었다. 따라서 분사연소합성 반응을 통해 세라믹 원료를 합성하기 위해서는 연소과정 중 열분해 거동과 평형종의 분압을 고려하여야 한다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.369-373
• /
• 2012

최근 강화된 국내외의 배출가스 규제 조건을 충족시키기 위해, 사용자의 요구대로 연료의 분사시기와 분사량을 조절할 수 있는 CRDI ECU 제어 알고리즘의 개발이 필요하다. 따라서 본 논문에서는 산업용 CRDI 엔진 전용 ECU에 적용할 수 있는 노킹 판별 및 엔진 밸런스 보정이 가능한 노킹 분석 시뮬레이터를 개발하였다. 개발한 노킹 분석 시뮬레이터의 결과를 OBD-II 표준을 사용하여 차량 위주의 진단기를 개발하여 운전자가 직접 차량을 진단할 수 있는 운전자 중심의 진단 서비스를 제공하고자 한다. 이를 위해 자동차 고장진단 신호 및 센서 출력 신호를 유선시스템과 무선 시스템인 블루투스 모듈을 이용하여 실시간 통신이 제공 될 수 있는 OBD-II 진단기 S/W 설계 방안을 제안함으로써 차량의 연비를 향상시키고, 유해 배출가스의 발생을 최소화하여 엔진 효율성의 개선 방안을 제시하고자 한다.