• Journal of Energy Engineering
• /
• v.7 no.1
• /
• pp.17-23
• /
• 1998

A simplified experiment was performed to figure out the atomization characteristics of highly viscous liquid of rice-bran oil by applying ultrasonic energy to improve the atomization of spray droplets. A spray system, an ultrasonic system, and three kinds of pintle-type nozzles(pin-edge angle: 5 , 10 , 15 ) were manufactured. To investigate the effects of ultrasonic energy on the atomization of a highly viscous liquid, a phase doppler particle analyzer was used for the measurement and calculation of spray droplets data. Nozzle opening pressures were chosen of 3 levels, i.e, 10, 13, 16 MPa. As a result, it could be concluded that the ultrasonic energy was effective to improve the spray atomization when applied to the fuel by means of 3 different nozzles because of the effects of the liquid fuel cavitation and relaxation between molecules caused by ultrasonic energy. The improvement rate of the spray atomization by the ultrasonic spray atomization by the ultrasonic spray compared with the conventional spray was about 10% increase in the case of pintle type nozzles. With the increase of pin-edge angles the distribution lines by nozzle opening pressures are declined for both conventional and ultrasonic sprays. This means that the increase of the pin-edge angle improves the atomization of sprays.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.1
• /
• pp.72-79
• /
• 2018

An experimental study was performed to investigate the chemiluminescence characteristics in the spray combustion of ultransonically atomized kerosene. The radical intensity of the spray flame was measured using an ICCD camera and the amount of fuel consumed was obtained by a precise flow-rate measurement technique during combustion. Fuel consumption increased linearly with the increase in carrier-gas flow rate, and typical group combustion, which is a characteristic of spray combustion, was observed. It was found from the analysis of chemiluminescence that the maximum emission intensities of OH and CH radicals decrease, and they move downstream resulting in the increase in a vivid reaction zone as the spray flow rate increases.

• Journal of the korean Society of Automotive Engineers
• /
• v.16 no.6
• /
• pp.16-21
• /
• 1994

본 연구에서는 연료의 핵심기술인 분사기술을 향상시키기 위하여 연료의 고압분사와 초음파 에너지 공급기술을 이용하여 연료의 미립화를 시도하고 EFI연료 분사방식에서 초음파 공급장치를 개발하여 추후 직접 분사식 초음파 무화장치의 개발을 위한 기초를 마련하고 직접 분사식에서 문제시되어지는 분사 초기 또는 분사 말기의 분사연료 미립화의 분사 전구간에서의 분사연료의 미립화를 시도하기 위한 기초를 마련하고자 한다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1999.10a
• /
• pp.1-1
• /
• 1999

2유체 동축인젝터(coaxial twin fluid injector)는 액체산소와 액체수소를 추진제로 사용하는 SSME(Space Shuttle Main Engine)이나 유럽의 Arian 5 Vulcain 엔진과 같은 저온추진제 엔진에 널리 사용되고 있다. 추진제를 미립화 시키는 장치로서 사용하는 다른 여러 형태의 인젝터에 비교할 때 저속의 액체산화제 주위에 고속의 가스연료가 분사됨으로서 발생되는 전단력에 의해 추진제가 미립화되는 특징을 가지며, 이러한 메카니즘은 매우 복잡하여 아직까지 정확히 규명되지 못하고 있는 실정이다.

• Journal of ILASS-Korea
• /
• v.3 no.4
• /
• pp.50-57
• /
• 1998

The utilization of resonance should be considered to get the maximum effect of ultrasonic to atomize liquid. The ultrasonic generator, transducer, horn, and all attached parts are used to produce the resonance, and specially the characteristics of liquids such as liquid load, property, and etc., for the liquid atomization affinity are considered. In this study, the variable device of liquid load was made and distilled water and city water selected as experimental liquids were sprayed by a twin-fluid spray method and their diameters, distributions, and spray quantum of spray droplets were measured by the light scattering system. And all data were observed, compared and considered relatively. In results, a lot of phenomena of liquid atomization affinity by ultrasonic appeared in accordance with liquid loads, namely head h.

• Proceedings of the KAIS Fall Conference
• /
• 2009.12a
• /
• pp.526-530
• /
• 2009

본 연구은 자동차용 가솔린엔진에 장착되는 인젝터의 연료공급 특성에 대한 것으로, 가솔린 엔진의 전자제어식 포트 연료분사는 분무장치와 흡기포트의 최적화 및 분무특성이 우수해야 엔진의 성능 향상 및 배기가스 저감의 목적을 이룰 수 있다. 4홀과 12홀 인젝터의 장착각 변화와 포트 마스킹의 형상변화에 따른 벽유량을 측정?분석하였고 분무가시화 실험을 통하여 분무성장과정과 분사각, 연료미립화 및 분무도달거리를 분석하였다. 벽류측정 실험을 통하여 벽류는 미립화정도와 흡기유동과 유속에 가장 큰 영향을 받는 것으로 판단되며, 12홀 인젝터 대비 4홀 인젝터는 분무압력에 따라 분무특성의 변화량이 크게 나타났다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.6 no.2
• /
• pp.37-44
• /
• 2002

A theoretical study of spray and combustion characteristics due to coaxial twin-fluid injection is conducted to investigate the effects of liquid jet property, droplet size, contact length and liquid jet velocity. Model is properly validated with measurements and shows good agreement. Prediction of jet contact length, droplet size, liquid jet velocity reflects genuine features of coaxial injection in physical and practical aspects. Both the jet contact length and tile droplet size are reduced in a linear manner with an increase of injector diameter. Cross sectional area of liquid intact core is reduced with augmented jet splitting rate, thus the jet is accelerated to maintain the mass continuity and with an assistant of momentum diffusion by burnt gas.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.141-144
• /
• 2009

An injector plays an important role in the process of an efficient combustion in liquid-rocket engines (LRE). This paper is focused on the injection performance of a small LRE-injector by employing the spray characteristic parameters made up of the velocity, Sauter mean diameter, and turbulence intensity. An experimental investigation is carried out with the aid of a dual-mode phase Doppler anemometry (DPDA) according to the injection pressure variation and along transverse axis, spatially. The Weber number and Reynolds number are used to characterize the atomization and turbulence nature of injector spray.

• Journal of ILASS-Korea
• /
• v.6 no.1
• /
• pp.25-34
• /
• 2001

Several efforts to meet the exhaust gas regulation have been undertaken by many researchers in recent years. Main researches are on development of design techniques of intake port and combustion chamber, atomisation of fuel and precise control of air-fuel ratio, post-treatment of exhaust gas and so on. Engine technology is changed from PFI to GDI to correspond with exhaust gas regulation. GDI technique makes it possible to preserve lean air-fuel ratio and control accurate air-fuel ratio. Nevertheless, It is not cleared that information of spray characteristics and atomization process are very dependent on fluctuation of pressure and change of temperature in intake stroke. In this study, a constant volume combustion chamber is manufactured to investigate various fluctuations of in-cylinder pressure for injection duration. It is taken photographs of injection process of conventional GDI injector using PMAS. Then, it was verified experimently that ambient conditions as temperature and pressure of combustion chamber have effects on process of spray growth and atomization of fuel.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.577-580
• /
• 2010

Coaxial injectors using GCH4/LOx as propellants was designed with shear(gas)/shear(liquid) type and shear(gas)/swirl(liquid) type. Spray characteristics were investigated by cold flow test. Spray patterns of the shear/shear and the shear/swirl type injectors were like a spout of water and hollow cone, respectively. Atomization efficiency of the shear/swirl type injector was better than atomization efficiency of the shear/shear type injector.