• 대한기계학회논문집
• /
• 제13권1호
• /
• pp.140-152
• /
• 1989

본 논문에서는 소형 고속 디젤 분무의 반경 방향의 연류 농도 분포를 고려한 비균질 분무의 분무 선단 도달 거리에 대한 관계식을 유도하고, 비정상 분무인 디젤 분무의 분사 차압-시간 곡선을 입력시킴으로써, 분사 초기 뿐 아니라 전 분사 기간의 분무 선단 도달 거리를 예측할 수 있는 새로운 모델을 제안하여 실험치와 비교 분석하였다. 그리고 분사각과 분열장의 무차원 실험식을 도출하여 계산에 사용하였고 분무 선단 도달 거리의 천이점과 분열장에 대하여 고찰하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.974-979
• /
• 2003

This study aimed to analyze spray characteristics and the ambient flow field in the mixture preparation state of the premixed combustion stage. It is very important to understand the spray characteristics and the fuel injection conditions in direct injection diesel engine because the emission gas compositions from diesel engines are related to spray formation processes of the premixed combustion stage. The numerical simulation was performed using the STAR-CD which is a commercial CFD code. Computed results of the transient high pressure diesel spray were compared with experimental results of the same spray injection condition in the constant volume chamber. The results show that spray patterns of numerical simulation agree with this experimental results comparatively.

• 한국자동차공학회논문집
• /
• 제3권6호
• /
• pp.8-22
• /
• 1995

Three dimensional numerical study of non-evaporating and evaporating spray characteristics was performed in a quiescent and motoring condition of direct injection diesel engine. The calculation parameter was breakup model. The breakup models used were Reitz & Diwakar model and TAB model. The modified k-${\varepsilon}$ turbulence model considering the compressibility effect due to the compression and expansion of piston was used. The calculation results of the spray tip penetration and tip velocity using the TAB model showed similar trends comparing with the experimental data. Although the evaporation rate was not nearly affected with the breakup model at the higher injection pressure, in the low injection case, the evaporation rate result using the TAB model became higher than that of R&D model. The evaporation rate was increased with the injection pressure due to the vigorous interaction with the gas field.

• 한국분무공학회지
• /
• 제10권1호
• /
• pp.17-23
• /
• 2005

Even though a relatively complete knowledge base has been established for diesel sprays, much of the knowledge cannot be directly translated to correlate the characteristics of gasoline spray. The macroscopic characteristics of gasoline impingement spray was investigated with photographic and image processing technique by Particle Motion Analysis System. The injector with single hole nozzle diameter of 0.28 mm was used in this experiment and the injection duration was selected as 10 msec. The injection pressure with 0.3, 0.35, and 0.4 MPa, impingement distance or 70, 100 and 130m, impingement angle or 0.15, 30 and $45^{\circ}$ were employed for the variables to affect the spray characteristics of impinging spray. It is clear that there is the analogy on the spray tip penetration between the gasoline impinging jet and diesel free jet. The spray tip penetration of impinging gasoline spray is proportional to the quarter power of the time after start of injection. The maximum height of impinging gasoline spray is also proportional to the quarter power of the time regardless of impingement distance, impingement angle and injection pressure. In addition, the effect of impingement angle on the spray tip penetration is significant according to the time after start of injection, even though there is minor effect in the initial stage of time after start of injection. Moreover, there is no remarkable effect of injection pressure on the spray tip Penetration under the experimental condition used in this study.

• 한국분무공학회지
• /
• 제4권2호
• /
• pp.40-46
• /
• 1999

Experimental investigation of unsteady impinging diesel spray on the flat plate have been carried out using high speed camera and Malvern system. The density ratios of ambient gas to diesel fuel were varied using $N_2$ and Ar gas in the case of 14.9, 21.2, 28.4, 35.1, 40.4, and 50.1. With the increase of gas density ratio, the radial penetration is decreased due to the resistance of the ambient gas. With the increase of the gas density ratio and the distance between nozzle tip and flat plate, the height of spray is increased due to the entrance and circulation. With the increase of gas density ratio, SMD is decreased on the nearby position at the center of flat plate, but SMD is increased on the far position. As the distance between nozzle tip and flat plate is increased, SMD is always decreased.

• 동력기계공학회지
• /
• 제14권2호
• /
• pp.16-21
• /
• 2010

분사된 연료의 미립화(atomization), 증발(evaporation), 그리고 혼합기형성과정(mixture formation process)이 디젤엔진의 착화 및 연소특성에 영향을 미치기 때문에, 디젤엔진 내에 분사된 연료의 구조해석으로부터 일련의 과정, 즉 고압분사, 분열(breakup), 미립화, 그리고 주위기체의 난류 도입(entrainment)에 관한 연구$^{1-3)}$는 꾸준히 행해져왔다. 본 연구는 증발디젤분무의 구조해석으로부터 디젤충돌분무의 혼합기형성과정을 조사한다. 주위기체의 밀도는 실험변수로서 선택하였고, $5.0kg/m^3$에서 $12.3kg/m^3$까지 변화시켰다. 그리고 소형고속디젤엔진에 있어서 연료분사초기의 상태의 고온 고압 설정이 가능한 정적용기를 사용했다. 주위 온도와 연료분사압력은 각각 700K 및 72MPa로 일정하게 유지했다. 충동증발분무의 액상과 기상의 이미지는 엑시플렉스형광법으로 동시 계측하였다. 실험결과로서 주위기체의 밀도가 높을수록 충돌분무의 선단도 달거리가 주위기체의 항력으로 인하여 감소하였다.

• 한국자동차공학회논문집
• /
• 제6권5호
• /
• pp.182-190
• /
• 1998

Behaviour of ultra-high pressure diesel spray in a constant-volume pressure chamber was studied with injection pressure ranging from 20 to 160㎫. Sprays were observed by the right angle scattering method. As a result, the spray tip penetration is first proportional to a time, and after that, it is proportional to 0.52 of the time during at the time of injection pressure and back pressure increase. An empirical correlation was made for the parameters of injection pressure, air-fuel density ratio, spray tip distance, spray angle, jet angle of spray and max. spray width.

• 한국자동차공학회논문집
• /
• 제4권2호
• /
• pp.137-146
• /
• 1996

Behaviour of ultra-high pressure diesel spray and its structure in a constant-volume pressure chamber were studied with injection pressure ranging from 35 to 110MPa. Sprays were observed by using the back illumination scattering method and righ angle scattering method. The spray process mechanism were investigated with both photographs. As a result, the spray angle and air entrainment angle was larger as injection pressure and back pressure increase. It becomes clear that mean air-fuel ratio is increased by increasing the injection pressure.

• 한국분무공학회지
• /
• 제6권4호
• /
• pp.39-48
• /
• 2001

The Gasoline Direct Injection(GDI) system has been highlighted due to the improvement of fuel consumption and the control of exhaust emission from gasoline engines. Main purpose of the present study is to measure spray characteristics of GDSI for real engine application. We have investigated experimentally spray tip penetration, spray angle, tip velocity and spatial spray distribution. Counter-rotating vortex grown on the spray surface plays an important role in the spray characteristics. Accordingly the spray tip penetration and tip velocity do not excess 50mm, 20m/s respectively, under 0.6MPa ambient pressure. the spray cone angle of GDSI have a same tendency to a simplex swirl atomizer.

• 한국분무공학회지
• /
• 제17권2호
• /
• pp.77-85
• /
• 2012

The CFD simulation of diesel spray tip penetrations were compared with 0-D simulation for experimental data obtained with common rail injection system. The simulated four injection patterns include single, pilot and split injections. The CFD simulation of the spray penetration over these injection patterns was performed using the KIVA-3V code, which was implemented with both the standard KIVA spray and original gas jet sub-models. 0-D simulation of the spray tip penetration with time-varying injection profiles was formulated based on the effective injection velocity concept as an extension of steady gas jet theory. Both the CFD simulation of the spray tip penetration with the standard KIVA spray model and 0-D simulation matched better with the experimental data than the results of the gas jet model for the entire fuel injection patterns.