• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.9
• /
• pp.667-674
• /
• 2014

A ship's propulsion shafting system is subjected to varying magnitudes of intermittent loadings that pose great risks such as failure. Consequently, the dynamic characteristic of a propulsion shafting system must be designed to withstand the resonance that occurs during operation. This resonance results from hydrodynamic interaction between the propeller and fluid. For ice-class vessels, this interaction takes place between the propeller and ice. Producing load- and resonance-induced stresses, the propeller-ice interaction is the primary source of excitation, making it a major focus in the design requirements of propulsion shafting systems. This paper examines the transient torsional vibration response of the propulsion shafting system of an ice-class research vessel. The propulsion train is composed of an electric motor, flexible coupling, spherical gears, and a propeller configuration. In this paper, the theoretical analysis of transient torsional vibration and propeller-ice interaction loading is first discussed, followed by an explanation of the actual transient torsional vibration measurements. Measurement data for the analysis were compared with an applied estimation factor for the propulsion shafting design torque limit, and they were evaluated using an existing international standard. Addressing the transient torsional vibration of a propulsion shafting system with an electric motor, this paper also illustrates the influence of flexible coupling stiffness design on resulting resonance. Lastly, the paper concludes with a proposal to further study the existence of negative torque on a gear train and its overall effect on propulsion shafting systems.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.380-388
• /
• 2016

Using the magnet gear, it is possible to transmit power without mechanical contact. As the drive shaft in a magnet gear-based speed reducer system is isolated from the drive shaft, the system is a two-inertia resonance system that should cope with an external load with the limited air-gap stiffness. On the other hand, the drive shaft or low-speed side is controlled only by the torque of the drive shaft through an air-gap, and the excessive oscillation or the slip can then be generated because of an abrupt disturbance that is different from the general mechanical gear system. Therefore, the disturbance loaded at the low speed side should be measured or estimated, and considered in the control of the driving shaft. This paper proposes a novel full-state feedback controller with a reduced-order observer for the speed reducer system using a magnet gear with a unified harmonic modulator. The control method was verified by simulation and experiment. To estimate the load at the low speed side, a novel observer was designed, in which the new state variable is introduced and the new state equation is formulated. Using a full-state feedback controller including the observer, the test result against disturbance was compared with two D.O.F PI speed controllers. The pole slip was compensated within relatively a short time, and the simulation result about the estimated variable shows a similar tendency to the test result. The test results showed that the magnet gear-based reducer can be applied to an accurate servo system.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.8-8
• /
• 2017

본 연구는 로타리 작업에 따른 105마력급 농업용 트랙터의 소요동력을 분석하기 위하여 수행되었다. 소요동력 측정 시스템은 차축 토크미터, PTO 토크미터, 주/보조 유압센서, 데이터 수집장치를 이용하여 구성하였다. 시험에 사용된 트랙터는 동양물산 105 HP급 트랙터 (S07, TYM, Korea)이며, 작업기는 로타베이터 (SW 230GL, Sungwoo Industrial Co. Ltd, Korea)를 사용하였다. 포장시험은 전라북도 부안군에 죽림길에 위치한 $4,000m^2$ ($100m{\times}40m$) 크기의 경작지 2곳에서 수행하였다. 포장시험 시 작업 단수는 주행단수 L3단 (2.38 km/h)에서 PTO 단수 1단 (540 rpm)과 2단 (750 rpm)으로 설정하였고, 로타리 작업 시 경심은 13 cm 조건에서 실시하였다. 트랙터 작업은 동양물산의 성능시험 업무를 맡고 있는 숙련된 작업자가 숙달된 방법으로 수행하였다. 포장시험지의 토양환경은 임의의 15곳에서 채취한 시료를 이용하여 토성, 함수율, 원추 관입지수에 대하여 미국 농무부 (USDA)법을 기준으로 분석하였다. 토양환경 분석 결과 토성은 Sandy loam (사양토), 평균 함수율은 35.15%, 평균 원추관입지수는 1,562 kPa로 나타났다. PTO 1단 작업 시 트랙터의 평균 소요동력은 차축, PTO, 주 유압, 보조 유압에 대하여 각각 1.8, 54.0, 1.3, 그리고 1.1 hp로 나타났다. PTO 2단 작업 시 트랙터의 평균 소요동력은 차축, PTO, 주 유압, 보조 유압에 대하여 각각 1.2, 79.4, 1.2, 그리고 1.0 hp로 나타났다. PTO 1단 작업 시 소요동력의 합은 58.2 hp로, 정격 마력 (105 hp) 대비 55.43 % 사용한 것으로 나타났으며, PTO 2단 작업 시 소요동력의 합은 82.8 hp로, 정격 마력 대비 78.85% 사용한 것으로 나타났다. PTO 1단 대비 2단에서는 PTO를 제외한 차축, 주 유압, 보조 유압의 소요동력이 감소하였으나, PTO에서 약 1.47배로 크게 증가하여 전체적으로 소요동력이 증가한 것으로 나타났다. 향후 다양한 작업기 및 작업 단수에 따른 소요동력을 분석하여 농업용 트랙터의 모든 부하 조건에 대한 데이터베이스 구축에 관한 연구를 수행할 예정이다.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.21 no.4
• /
• pp.545-560
• /
• 2019

During EPB TBM tunnelling, an appropriate application of additives such as foam and polymer is an essential factor to secure the stability of TBM as well as tunnelling performance. From the '90s, there have been many studies on the optimal injection of additives worldwidely contrary to the domestic situation. Therefore, in this paper, the foam, which is widely adopted for soil conditioning, was selected as an additive in order to investigate the effect of foam injection on TBM performance through a series of laboratory excavation tests. The excavation experiments were carried out on artificial sandy soil specimens with consideration of the variance of FIR (Foam Injection Ratio), FER (Foam Expansion Ratio) and $C_f$ (Surfactant Concentration), which indicate the amount and quality of the foam. During the tests, torque values were measured, and the workability of conditioned soil was evaluated by comparing the slump values of muck after each experiment. In addition, a weight loss of the replaceable aluminum cutter bits installed on the blade was measured to estimate the degree of abrasion. Finally, the foam injection ratio for the optimal TBM excavation for the typical soil specimen was determined by comparing the measured torque, slump value and abrasion. Note that the foam injection conditions satisfying the appropriate level of machine load, mechanical wear and workability are essential in the EPB TBM operational design.

• Journal of Drive and Control
• /
• v.17 no.2
• /
• pp.9-18
• /
• 2020

The purpose of this study was to analyze the effect of the soil cone index (CI) on the tractor work load. A load measurement system was constructed for measuring the field data. The field sites were divided into grids (3×3 m), and the cone index was measured at the center of each grid. The work load measured through the plow tillage was matched with the soil cone index. The matched data were grouped at 600 kPa intervals based on the cone index. The work load according to the cone index was analyzed for engine, axle, and traction load, respectively. The results showed that when the cone index increased, engine torque decreased by up to 9%, and the engine rotational speed and brake-specific fuel consumption increased by up to 5% and 3%, respectively. As the cone index increased, the traction and tillage depth were inversely proportional to the cone index, decreasing 7% and 18%, respectively and the traction and tillage depth were directly proportional to the cone index, increasing 13% and 12%, respectively. Thus, it was found that the cone index had a major influence on the engine, axle, and traction loads of the tractor.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.8
• /
• pp.1022-1027
• /
• 2011

A diesel engine works in high compression ratio due to injection of diesel fuel after compression of air. Therefore the engine has a high thermal efficiency, while nitrogen oxide is produced a lot in high flame temperature regions. In order to solve the problem this study HHO gas is added into the intake air of the industrial diesel engine. The test conditions are loads of 0%, 50% and 100% and engine speeds of 700 to 1900 rpm. The results show the maximum torque and pressure is increased, fuel consumption, smoke and CO emissions are decreased and NOx emission is remained at same level.

• Journal of the Korean Society for Railway
• /
• v.13 no.2
• /
• pp.166-172
• /
• 2010

Currently, vector control is used for speed control of trains because induction motor has high performance is installed in Electric railroad systems. Also, control of the induction motor is possible through various methods by developing inverters and control theory. Presently, rolling stocks which use the induction motor are possible to brake trains by using AC motor. Therefore model of motor block and induction motor is needed to adapt various methods. There is Variable Voltage Variable Frequency (VVVF) as the control method of the induction motor. The torque and speed is controlled in the VVVF. The propulsion system model in the electric railroad has many sub-systems. So, the analysis of performance of the speed control is very complex. In this paper, simulation models are suggested by using Matlab/Simulink in the speed control characteristic. On the basis of the simulation models, the response to disturbance input is analyzed about the load. Also, the current, speed and flux control model are proposed to analyze the speed control characteristic in the train propulsion system.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.12
• /
• pp.1209-1218
• /
• 2016

In order to safely and speedily transport a load such as a large glass plate using four electric cylinders, the synchronous error outside the permitted range should not be continuously generated between the cylinders. In this study, a methodology of synchronous control which can be applied to synchronization of four or more cylinders is developed. The synchronous control system based on the decoupling structure is composed of a reference model, position and synchronous controllers in the respective cylinders. The reference model is used for calculating the decoupled synchronous error and control input for the each cylinder. The position controller of I-PD type is designed in order that the cylinder may follow the reference signal without overshoot and input saturation. And the synchronous controller of lead compensator is designed to achieve stable and accurate synchronization through loop shaping approach. Finally, the simulation results show that the synchronization between the four cylinders can be quickly and stably while each cylinder rod is transferred to the target point under torque disturbance.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.3 no.3
• /
• pp.214-221
• /
• 1998

A new control approach using neural network for the robust position control of a BRUSHLESS direct drive(BLDD) motor is presented. The linear quadratic controller plus feedforward neural network is employed to obtain the robust BLDD motor system approximately linearized using field-orientation method for an AC servo. The neural network is trained in on-line phases and this neural network is composed by a feedforward recall and error back-propagation training. Since the total number of nodes are only eight, this system will be easily realized by the general microprocessor. During the normal operation, the input-output response is sampled and the weighting value is trained by error back-propagation at each sample period to accommodate the possible variations in the parameters or load torque. And the state space analysis is performed to obtain the state feedback gains systematically. In addition, the robustness is also obtained without affecting overall system response.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.6
• /
• pp.500-509
• /
• 2007

In this paper, we propose a novel pc-based 8-channel USB interface digital multi-controller (DMC) has capacity to be able to adjust ultrasonic motor's (USM's) the parameters-frequency, amplitude, phase difference using FPGA. The proposed DMC can control parameters directly by digital logic through a FPGA. Since it has counter circuit for rotary encoder to measure position and velocity of USM, the other separate circuits are unnecessary. Therefore, it could reduce the size of controller and the production cost. Finally, to verify the performance of proposed DMC, we tested the speed characteristic of two types USM with no-load as adjusting the parameters.