콘센트-플러그는 사용자부하에 전기를 공급하기 위하여 필수적으로 사용하는 전기부품이다. 활선상태인 콘센트-플러그를 임의로 차단할 경우, 교류환경에서는 반주기 마다 전류의 영점이 존재하므로 차단접점에서 발생하는 아크가 자연적으로 소호될 수 있으나 직류환경에서는 개방직전 전류가 영점을 포함하지 않고 일정하기 때문에 그에 따라 발생하는 아크는 교류에 비해 지속적이고 상대적으로 매우 큰 에너지를 방출한다. 교류에서 사용되는 플러그와 콘센트를 그대로 직류에서 사용 할 경우, 접속이 끊어 질 때 매우 큰 아크전류가 발생하여 플러그와 콘센트의 전극이 녹아서 붙는 융착 사고가 빈번히 발생한다. 본 논문은 콘센트-플러그의 융착 사고를 예방하기 위해 전극의 초기-후기접점 기법을 제안한다. 이를 구현하기 위한 기초적인 연구로서 초기-후기접점 저항을 2단계로 구분하여 접속 및 차단 시 중간단계의 접촉저항을 통하여 부하전류가 단계적으로 바뀔 수 있도록 함으로써 최종 차단 아크전류를 감소시키는 방법을 제안하고 실험을 통하여 성능을 분석하고 설계방법을 제시한다.
Journal of the Institute of Electronics Engineers of Korea SD
/
v.37
no.10
/
pp.33-41
/
2000
Pyroelectric characteristics such as voltage responsivity, noise equivalent power and detectivity are modeled 3-dimensionaly considering th interaction of each parameters. Also, the circuit is designed to set up the frequency band width and the signal amplification of the pyroelectric IR sensor. The case of low frequency region shows that the voltage response increases with the independence of the sensor area as the thickness decreases. In the high frequency region, it is found that the voltage response with the load resistor of 20$G{\Omega}$ increases with the independence of the sensor thickness as the sensor area decreases. In the low frequency region, the detectivity becomes excellent at th load resistor of 20$G{\Omega}$, the sensor area larger than $4{\times}10^{-10}m^2$ and the sensor thickness thinner than $1{\times}10^{-5}m$, while, in the high frequency region, it shows high value at the sensor thickness thinner than $1{\times}10^{-5}m$ and the sensor area smaller than $2{\times}10^{-10}m^2$ with the independence of the load resistor. In the circuit design, quasi-boot-strap circuit is employed, in which a single op-amp is connected to the drain of JFFT. Desirable frequency band width, amplification rate and the remarkable drop of noise of about 56% from that of conventional circuits with double op-amps are obtained.
Journal of the Institute of Electronics Engineers of Korea TC
/
v.43
no.2
s.344
/
pp.88-93
/
2006
In this paper, smaller load has been used compared with the conventional Doherty amplifier and PBG structure have been employed to suppress IMD (Inter-modulation Distortion) and improve PAE (Power Added Efficiency). And The PBG structure has been employed on the output macthing network of Doherty amplifier. The proposed power amplifier has been improved more the IMD3 by 5.5 dBc, and the average PAE by $5\%,$ at peak output power, $18\%$ at 8dB back-off point respectively than the conventional Doherty power amplifier.
Journal of the Korean Society for Aeronautical & Space Sciences
/
v.30
no.3
/
pp.77-86
/
2002
위성은 일단 한 번 발사하고 나면 운용궤도상에서 수리 및 회수가 거의 불가능하기 때문에 위성에 들어가는 모든 개발 부품들은 완벽한 설계, 충분한 해석, 고 작업도의 제작, 그리고 다양한 시험이 반드시 수반되어야 한다. 위성시스템에서 전자 소자의 신뢰성에 영향을 주는 인자는 다양하다. 과도한 열은 전자소자의 실패를 유발해서 결과적으로는 전체 위성의 실패를 유도할 수 있다. 이 논문에서는 다목적 실용위성 2호의 고전력 소산 전장품의 열부하 완화를 위한 방안을 경우별로 연구 비교하였다. 고전력 소산 전장품의 열부하를 완화하기 위해서는 하우징 두께의 증가가 필요하며, 전력조절기의 다이오드나 트랜지스터처럼 전력소산이 큰 소자에 대해서는 장착위치를 변경하거나 장착 부분의 열전도율을 증가시키는 방법이 필요하다. 또한 전력조절기처럼 장착면이 좁은 경우에는 복사의 영향이 크며, 이러한 전장품의 열부하를 완화하기 위해서는 주위 벽면의 온도를 낮추거나 하우징 표면 방사율을 증가시키는 방법이 효과적임이 알 수 있다.
Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
/
v.23
no.1
/
pp.109-115
/
2009
This paper describes an early detection for indication of electric accident using current waveform which is measured in electric equipments consisted incandescent lamps. At first, it analyzes characteristics of current monitor in resistive electric circuit. In second, the electric equipment is consisted of incandescent lamps. And the electric accident is simulation of tracking according to KS C IEC(Korea Standard C International Electrostatic Commission) 60112 at some part of the electric equipment. The indication of the electrical accident is detected to analyzing current waveform measured by current monitor. As the tracking breakdown, electric accident, processes, as current pulse is bigger and ratio of appearance also is increased irrespective of amount of load.
Journal of Advanced Marine Engineering and Technology
/
v.36
no.6
/
pp.837-843
/
2012
Asynchronous motors are widely used in many fields. The various starting methods have been developed for the asynchronous motors which have large power compared to source power. The most popular ways to start the motors are to reduce the voltage of motor's stator or change the resistance fed rotor. It is needed to the specific time to reduce the voltage and change the resistance at a specific step. We call it the switching time. It is very difficult to know the switching time exactly. It varies with different types of motors as well as load characteristics. Thus, this paper focuses on the design and development for the mathematical models of motor and load. And then it is implemented in SIMULINK in order to calculate this time. The simulation results are both compared and discussed in detail so that it can be applied for new system with various motors and loads.
The Transactions of the Korean Institute of Power Electronics
/
v.6
no.1
/
pp.34-42
/
2001
A battery is the device that transforms the chemical energy into the direct-current electrical energy directly without a mechanical process. Unit cells are connected in series to obtain the required voltage, while being connected in parallel to organize capacity for load current and to decrease the internal resistance for corresponding the sudden shift of the load current. Because the voltage droop down in one set of battery is faster than in tow one, it amy result in the low efficiency of power converter with the voltage drop and cause the system shutdown. However, when the system being driven in parallel, a circular-current can be generated. The changing current differs in each set of battery because the system including batteries, rectifiers and loads is connected in parallel and it makes the charge voltage constant. It is shown that, as a result the new batteries are heated by over-charge and over-discharge, and the over charge current increases rust of the positive grid and consequently shortens the lifetime of the new batteries. The difference between the new batteries and old ones is the amount of internal resistance. In this paper, we can detect the unbalance current using the micro-processor and achieve the balance current by adjusting resistance of each set. The internal resistance of each set becomes constant and the current of charge and discharge comes to be balanced by inserting the external resistance into the system and calculating the change of internal resistance.
The Transactions of the Korean Institute of Power Electronics
/
v.16
no.5
/
pp.415-429
/
2011
In this study, a single-phase quasi Z-source AC-AC converters with a series connection of the output terminals is proposed. The proposed system has configuration that the input terminals of two quasi Z-source AC-AC converters are connected in parallel and its output terminals are connected in series. The out of phase mode and in phase mode of the proposed system are presented. To verify the validity of the proposed converter, a DSP controlled hardware was made and PSIM simulation was executed. As a result, controlling the duty ratio of the converter, the desired buck-boost output voltages could be generated. For each modes, as compared with the single converter operation, the proposed converter could enhance the efficiency and input power factor according to different loads. Also, in case of the out of phase mode under the constant load, the efficiency and input power factor of the proposed system are increased 10[%], 35[%] respectively in compared with the single converter. And, the output voltage is constantly controlled in dynamic state in case while the load is suddenly changed.
The Journal of Korea Institute of Information, Electronics, and Communication Technology
/
v.12
no.2
/
pp.142-149
/
2019
The coils to transmit the electric energy are necessary to charge an electric vehicle wirelessly. There are several types of coils, from basic circular coils to DD-type coils for enhancing the coupling effect between two coils. However, DD-type coils with a good coupling effect between coils have a disadvantage in use because of the structure complexity of the power conversion device of transmitting and receiving side. In this paper, we propose a method to calculate the inductance value and to design the size of the spiral inductor which is convenient to fabricate when the power is transmitted wirelessly by using two coils in free space. Since the bifurcation phenomenon occurs when the XLm value is similar to the load resistance value in the resonator the XLm value was selected to be equal to the minimum load resistance value to minimize this phenomenon, and the inductance value required for the resonator was calculated. In order to realize the calculated inductance value by the spiral inductor, the relationship between the inductance value and the size, the number of turns, the total coil length of a spiral inductor was investigated. In addition, the change of coupling coefficient k according to the horizontal separation of two coils was examined and an appropriate inductor was selected.
The Journal of Korean Institute of Electromagnetic Engineering and Science
/
v.19
no.2
/
pp.231-236
/
2008
A method of moments model for the resistive vee dipole has been established. In order to validate the numerical model, an experimental model is built and reflections from the antenna in the feed line are measured. The measured data and the numerical data agree closely validating the numerical model. Based on the numerical model, efficiency of the antenna and the power dissipated in the resistors are analyzed. The results show that the antenna has low radiation efficiency because of the loading resistors and that the resistors near the drive point of the antenna dissipate more power than do the resisters far from the drive point. The results can be used to determine the amount of power that can be accepted by the resistive vee dipole, to determine the power rating of the loading resistors for a desired application, or to estimate the operation range of the antenna.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.