• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.1
• /
• pp.1-8
• /
• 2005

We fabricate PLT(5) thin film on Pt/TiO/sub x/SiO₂/Si substrate by using sol-gel method and investigate leakage current, switching and retention properties. The leakage current density of PLT(5) thin film is 3.56×10/sup -7/A/㎠ at 4V. In the examination of switching properties, pulse voltage and load resistance were 2V～5V and 50Ω～3.3kΩ, respectively. Switching time has a tendency to decrease from 0.52㎲ to 0.14㎲ with the increase of pulse voltage, and also the time increases from 0.14㎲ to 13.7㎲ with the increase of load resistance. The activation energy obtained from the relation of applied pulse voltage and switching time is about 135kV/cm. The error of switched charge density between hysteresis loop and experiment of polarization switching is about 10%. Also, polarization in retention decreases as much as about 8% after l0/sup 5/s.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.10
• /
• pp.932-935
• /
• 2015

This paper proposes a rectifier using bootstrapping and active body biasing in $0.11{\mu}m$ RF CMOS process. The proposed rectifier employs the full-wave rectifying structure with cross coupling and increases the power conversion efficiency by reducing the threshold voltage and leakage current using bootstrapping and active bias biasing. Also, it has been designed to be applied to a wide range of applications from 13.56 MHz used in wireless power transmission to 915 MHz used in RFID. As a measured result, 80 % of power conversion efficiency is obtained when the input power is 0 dBm at $10k{\Omega}$ load resistance and 13.56 MHz. Also 40 % of power conversion efficiency is shown in 915 MHz.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.1
• /
• pp.76-83
• /
• 2011

This paper focuses on the thermal design of a signal processor in Micro-Wave Seeker. High temperature environment and ESS(Environmental Stress Screening) test condition should be considered in designing a signal processor. First, we performed the thermal analysis to know conditions under which a signal processor is thermally reliable. As a result of thermal analysis, we found that adopting heat transfer block to the thermally fragile components is most efficient, because the heat transfer block can control the thermal loads of the individual components. Next, we verified this solution by numerical simulation and experiment and concluded that thermal reliability of a signal processor can be achieved. Maximum temperature difference between numerical simulation and experiment is about $2^{\circ}C$.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.6
• /
• pp.572-581
• /
• 2001

A heat pipe heat sink device which is to evacuate maximum heat of about 1800W from a powersemiconductor was designed and manufactured One set of cooling device os composed of an Aluminum block (130${\times}$160${\times}$35mm) 4 PFC heat pipes $(d_0 22.23mm)$ and 126 Aluminium fins (250${\times}$58${\times}$0.8mm) Experimental data obtained at a power of 1~2kW revealed that the total thermal resistance of the device varied 0.02~0.018$^{\circ}C$/W along with increasing air velocity from 2m/s to 3 m/s. The result represented a good satisfaction of requirement condition to maintain temperature rise of semiconductor lowe that $40^{\circ}C$ at 1800W and air velocity of 3 m/s Some important resistance such as convective resistances at both fins and heat pipes showed good agreement between mathematical predictions and measurement data.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.4
• /
• pp.1789-1796
• /
• 2012

In this paper, a new high-efficiency CMOS bridge rectifier for driving RFID tag chips is designed and analyzed. The input stage of the proposed rectifier is designed as a cascade structure connected with two NMOSs for reducing the gate capacitance by circuitry method, which is the main path of the leakage current that is increased when the operating frequency is increased. This gate capacitance reduction technique using the cascade input stage for reducing the gate leakage current is presented theoretically. The output characteristics of the proposed rectifier are derived analytically using its high frequency small-signal equivalent circuit. For the general load resistance of $50K{\Omega}$, the proposed rectifier shows better power conversion efficiencies of 28.9% for 915MHz UHF (for ISO 18000 -6) and 15.3% for 2.45GHz microwave (for ISO 18000-4) than those of 26.3% and 26.8% for 915MHz, and 13.2% and 12.6% for 2.45GHz of compared other two existing rectifiers. Therefore, the proposed rectifier may be used as a general purpose rectifier to drive tag chips for various RFID systems.

• KSBB Journal
• /
• v.11 no.1
• /
• pp.30-36
• /
• 1996

Based on fermentation data for cyclosporin A production, simple Monod kinetics was proposed for both immobilized and suspended cultures. Higher value of $\mu$mas and lower value of Km suggest better catalytic activity of the immobilized cells than the parallel suspended cells. Furthermore, lower Km value in the immobilized cell system indicates higher affinity of the immobilized cells for carbon substrate as compared with the suspended cells. For immobilized cell cultures, these parameters were also utilized for the estimation of effectiveness factor, an indicator for intraparticle mass transfer resistance. Based on simulation studies, optimum radius of celite beads was turned out $100 ~ 500{\mu}m$In this simulation work, we examined the influence of biosupport size and immobilized biomass density on diffusional resistance of substrate inside the bead matrix. In order to maintain uniformly distributed cell activities in biosupport, it was essential to determine optimum slze of particle, and then to estimate the most economic loaded biomass content.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.2
• /
• pp.115-124
• /
• 2001

In this paper, authors propose a new nonlinear rotor flux observer for rotor field oriented control of an induction motor which is designed based on the extended Luenberger Observer theory. Extended Luenberger Observer requires minimal solution of nonlinear partial differential equation on its coordinate transformation and linearization needed on a nonlinear observer design in general. The proposed rotor flux observer is derived from the 2 phase model of induction motor on the orthogonal coordination and it has the reduce gain matrix. Simulation and experimentation were performed under the conventional indirect vector control and direct vector control with the proposed observer at different rotor resistance. Simulation results show that the convergence of the proposed observer is influenced by the chosen eigenvalues. Experimentation results on load operation show the direct vector control with the proposed observer is better than the indirect vector control to maintain the characteristics of the vector control.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.2
• /
• pp.333-338
• /
• 2008

In this paper, a new NMOS current-mirror type bridge rectifier for driving RFID chips, whose minimum input voltage required to obtain the effective DC output voltage is low enough and whose power dissipation can be reduced than that of conventional one, is proposed. The designed rectifier is able to supply high enough and well-rectified DC voltages to drive RFID transponder chips for the frequency range of 13.56 MHz HF(for ISO 18000-3), 915 MHz UHF(fur ISO 18000-6), and 2.45 GHz microwave(for ISO 18000-4). Output characteristics of the proposed rectifier are analyzed with the high frequency equivalent circuit. And the circuitry method for effective reducing of the gate leakage current due to the increasing of operating frequency is also proposed theoretically. Using this method, the power consumption of $100\;{\mu}W$ and the DC output voltage of 2.13V for 3V peak-to-peak input voltage and $45\;K{\Omega}$ load resistance are obtained. Compared to conventional one, the proposed rectifier operates in more stable and shows superior characteristics in UHF and microwave frequencies.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.5
• /
• pp.747-756
• /
• 1999

In this paper, we analyzed microwave-DC conversion efficiency for the dual-polarization rectenna and antenna position changing. And then we analyzed and applied Square-Loop FSS structure for reducing the diode harmonic components as a rectifying circuit. The results of microwave-DC conversion efficiency for the each of designed dual-polarization rectenna has 69.1% with $360\Omega$ (dipole type) and 75.4% with $340\Omega$ (patch type) optimum load resistor. When the each of dual-polarization rectenna has a optimal load resistor, it's conversion efficiency shows of $\pm$20% in dipole type and $\pm$5% in patch type at $0~180^{\circ}$position. When applied Square-Loop FSS structure for Rectenna, Insertion loss was under 1 dB as the passband and over 20 dB as the stopband. The microwave -DC conversion efficiency was represented good properties of $\pm$2% variation.

• Fire Science and Engineering
• /
• v.29 no.2
• /
• pp.1-7
• /
• 2015

Tracking, which is one of main reasons of the electric fire, progresses gradually, and therefore, the possibility of fire caused by tracking can be predicted by analyzing the stage of its progress. This paper is conducted in order to predict possibility of the electric fire caused by the tracking in the simulated electric equipment with load. Non-inductive resistance is used as the load. The tracking is happened in a Polyvinyl-chloride-sheathed flat cord, which is a part of the simulated electric equipment by means of dropping of electrolyte droplet. In order to predict the possibility of electric fire caused by tracking, we detect the whole current waveforms of the simulated electric equipment. The time-energy analysis and probability distribution are used for analysis of the tracking progress from the whole current waveforms. In accordance with the results is used for input date of Neural networks, the neural networks can be predict possibility of the electric fire in the electric equipment by 4 stages.