• Journal of the Korean Magnetics Society
• /
• v.5 no.5
• /
• pp.880-894
• /
• 1995

Magnetic properties of $Nd_{x}{(Fe_{0.9}Co_{0.1})}_{90-x}B_{6}Nb_{3}Cu_{1}(x=\;3,\;4,\;5)$ rrelt-spun alloys with 6 at% B content were studied aiming for finding out a new $\alpha$-Fe based Nd-Fe-B nanocrystalline alloy with good hard magnetic properties. $Nd_{x}{(Fe_{0.9}Co_{0.1})}_{90-x}B_{6}Nb_{3}Cu_{1}$ melt-spun alloys prepared by RSP crystallized to nanocrystalline phase. An optimally annealed $Nd_{3}{(Fe_{0.9}Co_{0.1})}_{87}B_{6}Nb_{3}Cu_{1}$ melt-spun alloys had larger volume ratio of $\alpha$-Fe(Co) than that of higher Nd content alloy and showed high remanence of about 1.6 T. On the contrary, the increase of Nd content in $Nd_{x}{(Fe_{0.9}Co_{0.1})}_{90-x}B_{6}Nb_{3}Cu_{1}$ alloys gave rise to gradual increase of an amount of $Nd_{2}{(Fe,\;Co)}_{14}B$ phase and improved coercivity. An optimally annealed $Nd_{5}{(Fe_{0.9}Co_{0.1})}_{85}B_{6}Nb_{3}Cu_{1}$ alloy showed the most improved hard mag¬netic properties. The remanence, coercivityand energy product of the alloy were 1.35 T, 219 kA/m (2.75 kOe), and $129\;kJ/m^{3}$ (16.2 MGOe), respectively.

• Applied Chemistry for Engineering
• /
• v.9 no.3
• /
• pp.348-354
• /
• 1998

Cellulose grafted with acrylic acid(AAc) was prepared by radiation grafting technique. The effects of reaction temperature. reaction time, monomer concentration, and the crosslinkers on the AAc grafting reaction on cellulose were examined. The amount of AAc grafted on the cellulose reached maximum at the concentration of 0.75vol% difunctional crosslinker and 1.0vol% trifunctional crosslinker, respectively. In the presence of acid, the amount of AAc grafted on the cellulose was decreased when reaction solution contains difunctional crosslinker, while that was increased when reaction solution contains trifunctional crosslinker. In the grafting reaction of cellulose with AAc and TMETA, mixture containing ferrous sulfate and acid enhanced further AAc grafting yield than mixture containing ferrous sulfate only.

• Korean Journal of Materials Research
• /
• v.7 no.2
• /
• pp.145-151
• /
• 1997

Remelting of $A-Si/SiC_{p}$ composites followed by isothermal holding and solidification, leads ro the settling of Sic particles to the bottom of the mold. With the isothermal holding time for molten $A-Si/SiC_{p}$ composites. the particle free zone increases rapidly up to approximately first 30 minutes of the holding time. Experimental resulls of the particle settling confirm that the larger SIC particles sink faster tlun the sniiller particles. An increase in volume fraction of Sic particles decreases the setrling velocity of the particles.

• Proceedings of the Acoustical Society of Korea Conference
• /
• autumn
• /
• pp.265-268
• /
• 1999

감쇠가 큰 고분자 복합재료에서 초음파 다중반사파를 이용한 Pulse Echo법, 공진주파수에서 내부마찰계수 측정법과 Rheometer를 이용한 동적탄성계수 측정법을 사용하여 음향감쇠계수를 측정하고 각각의 측정자료를 비교하는 연구를 수행하였다. Pulse Echo법을 이용하여 0.5, 1.0, 2.25MHz에서 음향감쇠계수를 측정하였고, 이때 폴리에틸렌기지 복합재료의 음향감쇠계수는 강화재의 부피분율에 따라 3-15dB/cm 정도로 큰 값을 나타내었다. 폴리에틸렌기지 복합재료를 600kHz 근처에서 공진주파수를 가지도록 시편을 만든 후에 내부마찰계수를 측정한 결과로 계산된 음향감쇠계수는 Pulse Echo 실험에서 구한 값과 잘 일치하는 결과를 얻을 수 있었다. Rheometer를 이용한 동적탄성계수 측정법은 0.1-100Hz의 주파수에서 측정한 자료를 TTSP 이론을 이용하여 1MHz의 결과와 비교하였는데, 단일 고분자 재료에서는 다른 측정방법과 음향감쇠계수가 일치하였지만 복합재료에서는 음향감쇠계수값이 일치하지 않는 결과를 나타내었다.

• Composites Research
• /
• v.13 no.1
• /
• pp.50-60
• /
• 2000

This paper presents an analytical method considering tensile strength enhancement in hybrid $Al_2O_3$ fiber/particle/aluminum composites(MMCs). The tensile strength and elastic modulus of the hybrid MMCs are even 20% higher than those of the fiber reinforced MMCs with same volume fraction of reinforcements. This phenomenon is explained by the cluster model which is newly proposed in this research, and the strengthening mechanisms by a cluster is analyzed using simple modified rule of mixtures. From the analysis, it is observed that cluster structure in hybrid MMCs increase the fiber efficiency factor for the tensile strength and the orientation factor for the elastic modulus. The present theory is then compared with experimental results which was performed using squeeze infiltrated hybrid MMCs made of hybrid $Al_2O_3$ short fiber/particle preform and AC8A alloy as base metal, and the agreement is found to be satisfactory.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.1
• /
• pp.55-60
• /
• 2003

The effect of size and volume fraction of ceramic particles, with sliding velocity on the wear properties were investigated for the metal matrix composites fabricated by the pressureless infiltration process. The metal matrix composites exhibited about 5.5 - 6 times the wear resistance compared with AC8A alloy at high sliding velocity, and by increasing the particle size and decreasing the volume fraction, the wear resistance was improved. The wear resistance of metal matrix composites and AC8A alloy exhibited different aspects. Wear loss of AC8A alloy increased with sliding velocity, linearly : whereas, metal matrix composites indicated more wear loss than AC8A alloy at the slow velocity region. However, a transition point of wear loss was found at the middle velocity region, which shows the minimum wear loss. Further, wear loss at the high velocity region exhibited nearly the same value as the slow velocity region. In terms of wear mechanism, the metal matrix composites generally exhibited abrasive wear at slow to high sliding velocity； however, AC8A alloy showed abrasive wear at low sliding velocity and adhesive and melt wear at high sliding velocity.

• Journal of the Korean Society for Heat Treatment
• /
• v.15 no.6
• /
• pp.272-278
• /
• 2002

The changes in damping capacity with volume fractions of thermal and deformation-induced ${\varepsilon}$ martensites were compared and analyzed in an Fe-23%-Mn alloy. The volume fraction of thermal ${\varepsilon}$ martensite increased with decreasing cooling temperature, whereas that of deformation-induced ${\varepsilon}$ martensite increased steeply up to 10%- of cold rolling and nearly saturated in further cold rolling. In the case of thermal ${\varepsilon}$ martensite, the damping capacity increased linearly with the increase in ${\varepsilon}$ martensite content. For the deformation-induced ${\varepsilon}$ martensite, however, the damping capacity increased continuously up to 70%- of ${\varepsilon}$ martensite, over which it decreased suddenly. TEM microstructures showed that the deterioration of damping capacity above 70%- of deformation-induced ${\varepsilon}$ martensite is ascribed to the introduction of perfect dislocations, which play a important role in inhibiting the movement of damping sources such as stacking fault boundaries inside ${\varepsilon}$ martensite, ${\varepsilon}$ martensite variant boundaries and ${\gamma}/{\varepsilon}$ interfaces.

• Composites Research
• /
• v.17 no.2
• /
• pp.34-39
• /
• 2004

In this paper, a modified and representative unit cell model was employed to study the tensile behaviour of closed-cell metallic foams with varying spatial density distribution as well as material imperfections. The density variation was assumed to follow a statistical probability distribution of the Gaussian type. A multiple cell finite element model, utilising the modified unit cell, was developed. The model exhibits deformation patterns similar to those observed in tensile testing. The nominal stress-strain curve obtained from quasistatic tensile of the foam was compared with experimental findings and was found to be in good agreement in the scheme of maximum strength only if the appropriate density distribution and volume fraction of internal imperfections are taken into account. Moreover, maximum tensile strength of the aluminium foam was found to be more sensitive to the volume fraction of imperfection than standard deviation of the density.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.16 no.1
• /
• pp.1-8
• /
• 2003

Topology optimization has been evolved into a very efficient conceptual design tool and has been utilized into design engineering processes. Traditional topology optimization has been using homogenization method and optimality criteria method. homogenization method provides relationship equation between structure which includes many holes and stiffness matrix in FEM. Optimality criteria method is used to update design variables while maintaining that volume fraction is uniform. Traditional topology optimization has advantage of good convergence but has disadvantage of too much convergency time. In one way to solve this problem, element removal method using the criterion of an average stress is presented. As the result of examples, it is certified that convergency time is very reduced.

• Korean Journal of Materials Research
• /
• v.7 no.5
• /
• pp.444-450
• /
• 1997

기계적합금화 한 AI-Ti합금의 상온 및 고온 인장강도는 25at.% Ti을 Ce으로 치환함에 따라 증가하였다. 그러나 25at.% 이상의 Ce첨가는 합금의 인장강도를 감소시켰다. 이는 Ce이 적은 고용도 효과에 의해 금속간화합물의 초대화를 억제하여 합금의 강도를 증가시키지만 다량 첨가시에는 Ti에 비해 무거운 원자량으로 인해 분산상의 부피분율을 감소시켜 합금의 강도가 오히려 저하시킨 것으로 생각된다. Ce의 첨가는 40$0^{\circ}C$와 51$0^{\circ}C$에서 합금의 열저안정성을 향상시키는 것으로 나타났다. 300-51$0^{\circ}C$ 온도범위에서 측정된 AI-8wt.%(Ti+Ce)합금의 변형에 필요한 활성화에너지는 AI의 자기확산에 필요한 에너지 (142kJ/mode)의 1.3-1.9배로 나타났다. 이로부터 AI-Ti-Ce 합금의 고온 변형은 Orowan기구에 의한 것을 생각된다.