• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.05a
• /
• pp.787-790
• /
• 2003

A 4-wavelength optical transceiver system is designed and implemented by using 4 OADMs (optical add-drop multiplexers), WDMs, and optical transceivers. In this new system, the wavelengths of 1510 nm and 1530 nm are used for upload and download signals, respectively, as well as the wavelengths of 1550 nm and 1310 nm which have been utilized in a 2-wavelength optical transceiver systems. The 4-wavelength optical module shows very encouraging pass characteristics of about - 5 dB and isolation characteristics of less than -40 dB, which is configured with two OADMs, 4 couplers, and WDM couplers by fusion splicing. Noise figure (NF) of the one-stage balanced amplifier designed and fabricated for receiver module is 0.38 dB and the amplifying gain is 14.2 dB. S$_{11}$, S$_{22}$ and input, output VSWR are -28.81 dB, -32.08 dB, 1.05 : 1, 1.08 : 1, respectively.y.

• Resources Recycling
• /
• v.23 no.6
• /
• pp.30-39
• /
• 2014

The trajectories of PCB(Printed Circuit Board) particles in the corona discharge electrostatic separation was simulated. The PCB particles are prepared by crushing bare board, which disassembled from electronic components, consist mostly of copper and FR-4(Flame Retardant Level-4) Firstly, a model was established for calculating of detachment points of PCB particles from the rotating electrode in separator. The model of detachment points was derived from equilibrium of force such as gravity force, centrifugal force, electrostatic force. The trajectories of particles after detachment was calculated by acceleration derived from time-integrating method of motion equation. In this simulation, particle size, supplied voltage, rotation speed of rotating roll electrode and angle of induction electrode were adopted as variables. While the trajectories of FR-4 particles were affected by all variables, rotation speed of rotating roll electrode was dominant variables affecting trajectories of copper particles.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.9
• /
• pp.4171-4176
• /
• 2012

The conventional block systems for railway signaling currently in operation in Korea have not been electrified or integrated and therefore there have been difficulties in terms of construction and maintenance. Two independent systems have been installed for ABS and LEU of ATP system (for speeded-up lines), although they deal with the same signaling information at the same location in order to control the trains. In these conventional ABS and LEU, a number of duplicate modules are installed in each device including lamp detection units and power supply units and it results increased manufacturing costs and maintenance efforts. This paper deals with the prototype development of integrated electronic block system with CPU-based digital control methods in order to overcome the limitations of the conventional ABS. The suggested system is the integration of the conventional ABS with LEU of ATP and it is also applicable for the non-ATP sections as well.

• Journal of Satellite, Information and Communications
• /
• v.8 no.3
• /
• pp.47-51
• /
• 2013

In this paper, we present design and test results of a Ka-band dual-band ortho-mode transducer (OMT) for use in a feed assembly for the very small aperture terminals (VSATs). The designed ortho-mode transducer have wideband characteristics to separate the signals that have two orthogonal linear polarizations operating at 20GHz of receive frequency band and at 30GHz of transmit frequency band. In addition, in order to reduce the volume of the feed assebly, a Boifot based ortho-mode transducer has been designed with a dual-band. Experimental results for the design verification, the return loss in the receive band and in the transmit band for the horizontal polarization showed over 20dB and 21dB, respectively, and for the vertical polarization showed over 20dB and 24dB, respectively. The port isolation for the horizontal polarization and the vertical polarization showed over 43dB and 52dB, respectively, in the receive band and in the vertical band.

• Archives of design research
• /
• v.17 no.4
• /
• pp.401-404
• /
• 2004

The proposal defines a Do It Yourself system that radically changes the traditional concept of window. it is based on a D.I.Y. system that allows the users to fully customize its windows according to his needs, combining a wood frame with different elements. At the same time, it is preserving the basic function of light and ventilation and defining a new aesthetic code. Despite the restriction of size and shape, the user can choose among many different elements to increase the space efficiency he needs and to give a more enjoyable perspective to the window both in and out door. Also, All the elements are standard and they can be mass-produced according to specific market needs. Therefore, the window of the future will not be just a thin membrane in between the inside and the outside, but it will also play an important "identification role. According to each individual pick, these new windows will help to give identify to anonymous metropolitan areas and to the people living within them.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.42 no.4
• /
• pp.27-32
• /
• 2005

Liquid valve is divided into cylinder and liquid part or composed of a single body structure. It becomes a connected structure to cylinder head after inserting stainless(STS) shaft to Teflon packing. In injecting and intercepting fluid, working efficiency becomes low because of the top and bottom round trip operation the friction between Teflon packing and STS shaft fluid leakage, decline of working environment, and each part replacement. And so target value is unattainable in productivity liquid valve design, quality, and structure change are studied. In this paper, designed to solve the existing problems basically, to prevent friction of Piston by developing diaphragm linked with piston, to satisfy long life, and to provide the prevention of leakage. The objective of the study is also to prevent remains fluid at nozzle tip after dispensing fluid, and bell close with the suction function in piston retreating.

• Aerospace Engineering and Technology
• /
• v.6 no.2
• /
• pp.111-118
• /
• 2007

KSLV-I which is being developed in KARI is composed with two stages, and adaptor ring is used for coupling stage. Cables for interconnecting between stage is exposed on the outside. Also 8 pyro bolts which are installed in adaptor ring are used for separation of stage. In general, cowl is used for protecting exposed parts or structure which are anxious about damage from outer environment. In KSLV-I, two kind of cowls are designed. The one is umbilical cowl, and the other is pyro bolt cowl. Because cowl is exposed on the outside, heat and pressure load developed from air have effect on cowls. Therefore verification of structural strength through static analysis is required. In this study, static analysis in load condition except heat load is accomplished. In result of analysis, structural strength of pyro bolt cowl is verified. But breakage of umbilical cowl is confirmed in pressure load condition. So design of umbilical cowl is modified for satisfying required structural strength. And structural strength of umbilical cowl through analysis is verified.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.8
• /
• pp.849-855
• /
• 2014

The GFRP composite is used for hot press flow molding of automotive components, and the different flow rates of fiber and plastic are likely to induce fiber orientation and inhomogeneity in the material. However, very limited systematic research studies are available on composite materials with superior flow homogeneity and optimized fiber orientation. The inhomogeneity and fiber orientation issues of GFRP composites have still not been resolved through research. The plain weaving method applied to the GFRP prepreg can improve its recyclability, inhomogeneity, fiber flow, structural stability, fiber deformation, surface smoothness, degree of impregnation, and other mechanical properties. The need for more detailed and thorough studies is evidenced.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.3
• /
• pp.784-794
• /
• 1996

In this papre, the design and the fabrication of the surface mountable voltage controlled oscillator is described for local oscillator in PCS(WACS/TDMA) handset. The VCO employs two silicon bipolar transistors of $f_{gamma}$ of 4 GHz as active devices. These are asembled to form the VCO on the 4 layer PCB of the size $12{\times}10mm$which provides the strip line resonator at the third layer. The fabricated VCO shows tuning rage over 50 MHz, phase noise -100 dBc/Hz at the 100 kHz frequency offset, and 0 dBm output power with the consumption of 22 mA at 3V. It is belived that the size will be more reduced by employing 1005 chip components and that the current consumption will be improved by employing transistors of higher $f_{gamma}$.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.41 no.2
• /
• pp.11-22
• /
• 2004

Conventional algorithms of separating overlapped objects are mostly based on template matching methods and thus their application domain is restricted to 2D objects and the processing time increases when the number of templates (object models) does. To solve these problems, this paper proposes a new approach of separating the occluding object from the stack of 3D objects using the relationship between surfaces without any information on the objects. The proposed algorithm considers an object as a combination of surfaces which are consisted with a set of boundary edges. Overlap of 3D objects appears as overlap of surfaces and thus as crossings of edges in 2D image. Based on this observation, the types of edge crossings are classified from which the types of overlap of 3D objects can be identified. The relationships between surfaces are represented by an attributed graph where the types of overlaps are represented by relation values. Using the relation values, the surfaces pertained to the same object are discerned and the overlapping object on the top of the stack can be separated. The performance of the proposed algorithm has been proved by the experiments using the overlapped images of 3D objects selected among the standard industrial parts.