• Composites Research
• /
• v.25 no.2
• /
• pp.46-53
• /
• 2012

Using pultrusion process, FRP composite structural members having various cross-section shapes can be produced with unlimited lengths. Because of such reasons, these members are suitable for the application in the construction field. Especially, this material is highly appreciated if the material is to be used in the corrosive environments such as aquatic or oceanic environments due to its high corrosion resistance. However, design criteria for the FRP structural member are not developed yet. So, the research on the development of design guideline is needed ungently. In order to use the pultruded structural FRP member efficiently, the members are composed of thin plate components, and thus, the member is prone to buckle easily and the buckling is one of the governing strength limit states for the design. In this paper, we present the analytical study results pertaining to the buckling behavior of I-shape FRP compression member. In addition, design procedure and flow-chart are also proposed based on the study results including previous experimental results. Proposed design procedure is similar to that in ANSI/AISC 360-10 with minor modification. Therefore, it is convinced that the structural design of pultruded FRP compression member could be done easily by following design procedure proposed in this paper.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2011.04a
• /
• pp.702-705
• /
• 2011

본 논문에서는 초고층 전단벽-아웃리거 시스템에 대해, 기존의 근사해석법과 유전알고리즘을 이용하여, 물량최적설계 기반의 구성요소 단면 및 아웃리거 최적위치 결정에 관해 연구를 진행하였다. 아웃리거 시스템의 최적성은 아웃리거의 위치와 아웃리거 시스템을 구성하는 전단벽-아웃리거, 외곽기둥의 단면 성능의 복잡한 관계에 의해 역학적으로 결정된다. 하지만 기존의 아웃리거 시스템의 최적화 연구는 대부분 전단벽과 아웃리거, 외곽기둥의 단면은 고정된 상태에서, 아웃리거의 위치만 설계변수로 하여 아웃리거의 최적위치를 찾는 연구에 국한되어 있다. 이에 본 연구에서는 G.A.를 이용하여, 아웃리거 설치위치뿐만 아니라 전단벽과 아웃리거, 외곽기둥의 단면까지 설계변수로 하여 물량최적설계 조건을 만족시키는 아웃리거시스템의 최적설계 연구를 진행하였다. 또한 반복 계산의 시간을 줄이기 위해 기존의 근사해석법을 사용하였다. 본 연구의 결과는 초고층 구조물의 초기 설계 시에 구성요소의 단면 및 아웃리거 설치 층의 선정에 적극 활용될 수 있을 것이다.

• Journal of Korean Association for Spatial Structures
• /
• v.6 no.1 s.19
• /
• pp.101-109
• /
• 2006

An initial member sections of steel structures is selected by experience of expert building structural designers. And appropriate member section is designed by repeat calculation through structural analysis. Therefore an initial assumption of member section is necessary for saving the time for structural design and is important to acquire safety of building structures. Also brace damper are generally used to prevent or decrease stuctural damage by its hysteretic behavior in building structures subjected to strong earthquake. Based on plastic design, the initial section of members for architectural steel structures with hysteretic damper braces is presented and seismic effect of structural behavior by the ratio of damper stiffness to structural story stiffness is estimated in this paper.

• Journal of Korean Society of Steel Construction
• /
• v.23 no.2
• /
• pp.249-259
• /
• 2011

In this study, the distortional behaviors of tub-section steel girders subjected to torsional loading were analyzed, and predictor equations were developed for estimating the member forces induced in the internal bracing system installed in the steel tub girders. Torsional loadings originated either by eccentric vertical loading or girder curvature were decomposed into the pure torsional force component that does not affect the distortional box deformation, and into the distortional force component that directly induces box distortion. The axial member forces induced in the internal cross frames were formulated as a function of the magnitude of torsional loading through the analytical investigation of the interactions between the distortional force component and internal cross frames. To verify the proposed equations, three-dimensional finite element analysis (3D FEA) was conducted for the straight simple-span girder and the three-span continuous girder samples. Very good agreement was found between the member forces from the FEA and the proposed equations.

• Journal of Korean Association for Spatial Structures
• /
• v.7 no.3 s.25
• /
• pp.119-124
• /
• 2007

Due to the deficit of section of web, the buckling strength of cellular beam become smaller than that of H-beam. In this thesis, we evaluate the buckling strength of web-post through non-linear F.E.M with opening distance-diameter ratio and opening diameter - web thickness ratio as essential variables. And also analyzes this comparing with the standard indicated in BS5950 Part 1.

• Magazine of the Korea Concrete Institute
• /
• v.14 no.1
• /
• pp.19-22
• /
• 2002

건축공학과를 졸업하고 구조설계 실무 분야로 진출하는 이의 비율이 3~5%라는 비공식 통계가 있다. 이 통계 숫자가 말하듯이 건축구조설계업은 건축공학과 졸업자가 택하는 소수의 직업군에 속한다. 재학시에는 콘크리트 구조, 강구조 및 여타 구조 과목을 해당 분야를 전공한 교수진으로부터 각각 배우지만 실무에서는 맡겨진 프로젝트에 의해 구조 형식이 결정되고 스스로의 노력과 회사 내 시스템을 통해 해결해야 하므로 구조 형식 전반에 걸친 프로패셔널(professional)이 되어야 한다. 콘크리트에 대한 전문지식도 학교에서는 콘크리트의 기본 사항, 수직 및 수평 부재의 단면 설계 연습 등을 통해 기본적인 단계의 지식을 습득한다. 그러나 실무에서는 구조 시스템, 콘크리트 프레임의 거동 및 수많은 부재의 단면 설계 등과 같이 포괄적인 지식이 주종을 이룬다.(중략)

• Journal of the Korea Concrete Institute
• /
• v.23 no.3
• /
• pp.353-364
• /
• 2011

In a previous research performed by the authors, the allowable compressive stress coefficient (K) in pretensioned members with rectangular section at transfer was proposed based on strength design theory. In this study, a subsequent research of an enormous analysis was performed to determine the K factor for Tee and inverted Tee section members, considering the effect of section height (h), section type, amount of tendons ($A_{ps}$), and eccentricity ratio (e/h). Based on the analysis results, the allowable compressive stress coefficients (K) for Tee and inverted Tee section members at transfer were derived, which limit the maximum allowable stresses as 80% and 70% of the compressive strengths at the time of release for Tee section and inverted Tee section, respectively. And these were larger than the allowable stresses specified in domestic and other international codes. In order to verify the proposed equations, they were compared to the test results available in literature and other codes, which showed that the allowable stresses in domestic and international codes are unconservative for the cases with low eccentricity ratios while conservative for those with high eccentricity ratios. The proposed equations, however, estimate the allowable stresses of the Tee and inverted Tee section members reasonably close to test results.

• Journal of Korean Society of Steel Construction
• /
• v.19 no.6
• /
• pp.611-620
• /
• 2007

The beam-column connection is the critical design section of general steel frame structures owing to the behavioral characteristics of the structural system. As most members of a frame structure are composed of rolled section beams, the cross-section of the beam members is governed by the negative bending moment near beam-column connections. Such a design concept leaves a redundant load-carrying capacity at the positive bending regions of the beam members leading to design inefficiency. Therefore, it is of utmost importance to redistribute the beam end moments and reduce the stresses at the beam-column connections for a more efficient design of steel frame structures. In this study, reaction-moment prestressing method (RMPM) was proposed for the innovative design and construction of steel frame structures. The RMPM is a prestressing method utilizing the elastic bending deformation of a beam member induced by temporary prestressing for the distribution of a relatively large bending moment to other sections for the efficient use of the beam section. By the application of the RMPM, the negative bending moment at the beam-column connections can be significantly reduced, ultimately leading to possible use of smaller beam sections. Through a series of model tests and numerical analyses of steel frame structures, the moment distributing effect and feasibility of the RMPM was verified.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.197-200
• /
• 2008

An analytical model for predicting the shear strength of prestressed concrete beams was developed, applying the previously proposed strain-based shear strength model. In flexure-compression member without shear reinforcement, compression zone of intact concrete primarily resist to the shear force rather than tension zone. The shear capacity of concrete at the compression zone was defined based on the material failure criteria. The shear capacity of the compression zone was evaluated along the inclined failure surface considering interaction with the normal stress. Since the distribution of normal stress varies due to the flexural deformation of member, the shear capacity was defined as a function of the flexural deformation. Finally, the shear strength was determined at the intersection of the shear capacity curve and the shear demand curve. As a result of the comparisons to prior test data, the proposed model accurately predicted the shear strength of specimens.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.5
• /
• pp.1363-1372
• /
• 2014

In the previous study, the structural performance of proposed precast concrete arch with reinforced joint was evaluated by structural experiment. In this paper, finite element analysis considering both material and contact nonlinearity was carried out on the specimens of the previous study. Based on the result of analysis and experiment, friction coefficient between concrete blocks was determined. To evaluate the strength of sectional member, elastic analysis was carried out on the arch using linear elastic analysis program. The section force was compared with the nominal strength of arch section. It was concluded that the maximum load of all the specimens exceed the nominal strength of arch section. Those results of the strength evaluation were similar to the results of structural experiments. Therefore, it is concluded that the elastic analysis and ultimate strength model can effectively evaluate the strength for the proposed precast concrete arch composed of concrete blocks and reinforced joint in design.