• Journal of the Korea institute for structural maintenance and inspection
• /
• v.19 no.1
• /
• pp.72-80
• /
• 2015

In this study, comparative analysis has been performed with regard to a bending stress and deformation at bottom slab of a concrete floating container terminal by live load distributions. In addition, a structural performance and behavior of the floating structure is considered using a numerical analysis. Through reviewed structural performance of a floating structure by live load distribution, the structure presented tensile behavior by two live load cases (A, B, D-type). Then, the other live load cases (C, E, F, G, H, I, J-type) shows compressive behavior. Especially, immoderately compressive stress was generated on bottom slab at specific load distribution. but, that should be decreased through controling buoyancy pre-flexion. Through reviewed structural behavior, slopes of structure by four live load cases (B, E, F, H-type) were exceeded in design criteria of mega-float. It should be estimated that it get out of the load case at loading container. In all, the present study can be considered as a benchmark of a floating container terminal in the absence of analysis and will be used to guide-line about serviceability of concrete floating container terminal.

• Journal of Korea Water Resources Association
• /
• v.32 no.1
• /
• pp.83-94
• /
• 1999

In continental margins, turbid underflows which are not confined to a given channel, are free to spread laterally as well as longitudinally. Lateral spreading can reduce substantially the run out distance of flows along continental shelves and slopes. Laboratory experiments with a large tank, employing saline density currents as surrogates for fine-grained turbidity flow, coupled with dimensional analysis, have been used to develop a simple expression for lateral spreading rates of two-dimensional flows on sloping beds. characteristic length and time are determined by the flow discharge and buoyancy flux at the inlet. By knowing the initial width of the flow, the spreading law can be used to estimate the maximum width of the current at different times as well as the longitudinal spreading rate. Predictions for flows compare favorably against observations.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.8
• /
• pp.178-184
• /
• 2014

In this study, we develop liquid density sensor by measuring of balanced position between gravity and bouyancy, corresponding to liquid density, using distance measuring by magnetostriction technology. For improvement of accuracy of liquid density sensor system. And we derive the related equation between liquid density and moving distance of density sensor, and make the calibration method for liquid density sensor by magnetostriction technology. Using fabricated liquid density sensing system and derived equation, have measured the density of several liquids. And compare it to measuring results using Oscillating U-tube type high accuracy density meter, having 0.000001 g/cc resolution. The deviation of results between two density measuring systems was less than 0.001 g/cc.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.5
• /
• pp.743-749
• /
• 2010

The primary object of this study was to develop the control algorithm and program for automatic submersible buoy which is free to move vertically within the water column by adjusting weight and buoyancy forces by air control. The experiment was performed to validate the usefulness of the program in the indoor water tank. In the experiment, the automatic submerging and surfacing of the buoy were controlled by water-pressure gauge and air control system. The buoy is raised by injecting compressed air from a compressor and then is lowered by releasing the air. The submerging and surfacing characteristics of the buoy calculated with the numerical model were similar to measurements obtained with the experiment. It was concluded that the algorithm and program could be useful in analyzing various parameters and submerging mechanisms required to design new type of automatic submersible fish cage system.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1328-1333
• /
• 2004

The Flame length of $CH_4$ with the Oxidizer of air and $O_2$ has been measured respectively for the nozzle diameter of 1.6mm, 2.7mm, 4.4mm and 7.7mm. In all $CH_4$ flame on oxidizer of air and $O_2$. the flame length was independent of the initial jet diameter, dependent only on the flowrate in laminar flame regime, and in turbulent flame dependent on the initial jet diameter. Using correlation equation of Delichatsios, the flame length has been expected exactly for $CH_4/air$ flame, but has been underestimated for $CH_4/O_2$ flame. This paper has proposed correlation equation of $CH_4/O_2$ flame.

• KEPCO Journal on Electric Power and Energy
• /
• v.2 no.3
• /
• pp.461-467
• /
• 2016

In order to install the floating transport type wind-turbine foundation, water pumping is used to sink the foundation. During this process, its mass and center of gravity, and buoyancy center become continuously changed so that the dynamic stability of the floating foundation become unstable. Dynamic stability analysis of the floating foundation is a complex problem since it should take into account not only the environmental wave, wind, and current loads but also its weight change effect simultaneously considering six-degree-of-freedom motion. In this study, advanced numerical method based on the coupled computational fluid dynamics (CFD) and multi-body dynamics (MBD) approach has been applied to the dynamic stability analysis of the floating foundation. The sloshing effect of foundation internal water is also considered and the floating dynamic characteristics are numerically investigated in detail.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.4 s.107
• /
• pp.380-386
• /
• 2006

Electric fuel sender fur the vehicle fuel gauge system was designed and fabricated based on the CPW(Co-Planer Waveguide) transmission line theory. It is applied on this system that characteristic impedance of RF transmission line can be varied by the surrounded material of the line. By the characteristic impedance owing the level of gasoline or diesel fuel in vehicle fuel tank, CPW line has corresponding reflected signal as much as changed impedance. Detected signal is amplified, and delivered to fuel indicator into cluster unit on dash board. Conventional floating mechanical buoy level gauge has several defects as low reliability and high break down rate by mechanical operation, and has not good linearity for the fuel level difference. CPW line with electric circuits are constructed on 1.6 mm thickness epoxy substrate, and measurement shows that this system has more accurate level and better linearity than conventional mechanical system. New electric fuel sender which has good productivity with long lifetime and low-in-cost by the SMT chip assembling could be replaced this system with conventional floating buoy system.

• Solar Energy
• /
• v.12 no.3
• /
• pp.70-83
• /
• 1992

The interaction between the surface radiation and the mixed convection transport from an isolated thermal source, with a uniform surface heat flux input and located in a rectangular enclosure, is stuied numerically. The enclosure simulates a practical system such an air cooled electric device, where an air-stream flows through the openings on the two vertical walls. The heat source represents an electric component located in such an enclosure. The size of this cavity is $0.1[m]{\times}0.1[m]$. The inlet velocity is assumed as 0.07[m/s] and the inlet temperature is maintained as $27^{\circ}C$. The inflow is kept at a fixed position. Laminar, two dimensional flow is assumed, and the problem lies in the mixed convection regime, governed by buoyancy force and surface readiation. The significant variables include the location of the out-flow opening, of the heat source and the wall emissivity. The basic nature of the resulting interaction betwwn the externally induced air stream and the buoyancy-driven flow generated by the source is investigated. As a result, the best location of the heat source to make the active heat transfer is 0.075[m] from the left wall on the floor. The trends observed are also discussed in terms of heat removal from practical systems such as electric circuitry.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2008.05a
• /
• pp.1373-1377
• /
• 2008

강우-유출에 의해 성층화된 저수지로 유입하는 하천수는 저수지 표층에 비해 낮은 수온과 높은 부유물질(SS) 농도를 가지므로 저수지 표층수보다 상대적으로 높은 밀도를 유지한다. 하천으로부터 유입한 밀도류는 유속에 의한 관성력이 두 수체의 밀도차에 의한 음의 부력보다 큰 구간까지는 저수지 표층을 따라 진행하지만, 두 힘이 같아지는 지점에서 밀도류는 더 이상 진행하지 못하고 저수지 수면 아래로 침강하며 이 과정에서 수체간의 많은 혼합이 일어난다. 따라서 홍수시 유입한 탁수의 침강점에 대한 정확한 예측은 수질관리를 위한 현장조사, 그리고 탁수거동 해석 및 최적관리대책 마련에 중요한 요소이다. 본 연구의 목적은 홍수시 대청호로 유입하는 하천 밀도류의 침강위치를 홍수규모별로 경험식과 수치모델을 통해 산정함으로써 두 방법 간의 장 단점을 비교하고, 탁수 현장조사와 최적관리를 위한 기초정보를 제공하는데 있다. 유입수의 모의조건은 그 동안 대청호에서 발생한 홍수 크기를 기준으로 9개의 등급으로 나누었으며, 저수지 성층조건은 여름철 탁수가 유입되기 전의 발달된 성층구조를 적용하였다. 유입수와 저수지 성층구조의 특성치는 밀도 Froude 수($Fr_i$)로 나타냈으며, $Fr_i$ 조건별로 침강점 위치를 저수지 단면을 삼각형태로 가정한 Hebbert et al.(1979) 경험식과 2차원 수치모델로 산정하여 그 결과를 비교하였다. 대청호로 유입한 탁수는 홍수규모에 따라 대정리 수역에서 회남수역 사이 구간에서 침강하였으며, $Fr_i$ 값이 클수록 침강점 수심이 깊어지는 경향을 보였다. 경험식으로 산정한 침강점 수심은 정상상태 조건을 가정하므로 홍수에 의한 수위변화를 고려하지 못하며, 실제의 불규칙한 하상표고를 일정한 하상경사로 가정하기 때문에 2차원 모델의 결과보다 과대산정하는 경향을 보였다. 따라서 홍수가 연속해서 발생하며 수위변화가 심한 국내 저수지 여건에서 하천 유입 밀도류의 거동을 보다 정확히 예측하기 위해서는 2차원 또는 3차원 수치모델을 적용하는 것이 타당할 것으로 판단된다.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.5
• /
• pp.871-879
• /
• 2011

The internal deck structure of turtle ship has been investigated with the following approach manner. Firstly the 5 species of turtle ship are identified by examining the characteristics of 5 turtle ships revealed by the librarian or paintings. Secondly the centers of gravity and buoyancy for each type are calculated to evaluate the turtle ship's buoyancy stability. Thirdly the optimal deck structures for 5 turtle ships are additionally assessed from the viewpoint of the interoperability of soldier's missions to get more meaningful conclusion. From the results obtained by the well refined analyses above, one can identify that Changjeguyseon and Lee Chung Mu Gong descendent family's turtle ship possess one layer deck, and the tongjeyoung and jwasuyoung turtle ship consist of 1 and half story deck, and the one disclosed by Yoon has 2 story structure.