• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.10
• /
• pp.4845-4852
• /
• 2012

This research calculated the scour depth of bridge according to inflow and outflow changes of stream's flood discharge and curves by applying scour depth formula for piers and abutments, and by comparing and examining them, evaluated the applicability of scour depth formulas. Overall, if the angles of flood discharge and inflow and outflow increase, the deviation rate of scour depth in bight increased. Especially the deviation rate was 58% at the inflow and outflow angle of $105^{\circ}$ that the bridge plan for this geography need careful examination. Next, as a result of calculating the deviation rate of scour depth at the bight by scour depth formulas, in case of pier, Andru formula showed 58% deviation rate, Laursen formula showed 26% deviation rate, and CSU. formula showed 17% deviation rate. In the case of abutment, Froehlich formula shows 44% deviation rate that when applying above scour depth formulas, scour depth calculation considering repairable characteristics of bight is necessary. Finally, about inflow and outflow angles of $45^{\circ}{\sim}135^{\circ}$ that showed big deviation rate of scour depth, this research performed regression analysis of deviation rates of scour depth due to flood discharge to suggest the regression formula.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.13 no.5
• /
• pp.173-181
• /
• 1993

Under natural conditions, rivers do not in general take straight courses but instead take winding courses. This is known as meandering of rivers. Meandering of rivers are so complicated because of the mutual interactions between flow and movable boundaries. In quantitative information, it is important to predict the future location of a river channel(channel migration) because in selecting a bridge site or a location of a road. It may be valuable to know the future impact of a nearby river on those structures. When the prediction model of the migration of channel is used in domestic rivers with high coefficient of river regime, it is rational to use the periodical dominant discharge (PDD), which is named firstly by the author, instead of the average discharge. According to the analysis of the erosion coefficient, the mean deviation on the channel migration, and the bed scour factor, it can bring shedding light on the fact that the discharge is one of the dominant components in channel migration. In project area, the discharge that can shift the channel is slightly greater than 6,000CMS. The prediction model of the migration of channel estimated the erosion coefficient, $E_0$ by the data from the South Han River. This estimated value from the South Han River was also used to predict the migration of the South Han River in year 2000.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.1
• /
• pp.470-476
• /
• 2019

The braking force for a train is generally provided by compressed air. The pressure valve system that is used to apply appropriate braking forces to trains has a complex flow circuit. It is possible to make a channel shape that can increase the flow efficiency by 3D printing. There are restrictions on the flow shape design when using general machining. Therefore, in this study, the compressed air flow was analyzed in a pressure valve system by comparing flow paths made with conventional manufacturing methods and 3D printing. An analysis was done to examine the curvature magnitude of the flow path, the diameter of the flow path, the magnitude of the inlet and reservoir pressure, and the initial temperature of the compressed air when the flow direction changes. The minimization of pressure loss and the uniformity of the flow characteristics influenced the braking efficiency. The curvilinear flow path made through 3D printing was advantageous for improving the braking efficiency compared to the rectangular shape manufactured by general machining.

• Journal of the Korea Convergence Society
• /
• v.13 no.3
• /
• pp.191-196
• /
• 2022

Unlike an international combustion engine car, a battery-powered electric vehicle requires an additional heat source for its heating system. A high-voltage coolant heater has the advantages of high efficiency and a wide operating temperature range. In its development, the geometry design of the coolant flow path is essential. This paper presents the thermal flow simulations of a 7kW high-voltage heater with symmetric serpentine flow channels arranged parallelly. The heater performance was evaluated from the simulation results in terms of the pressure and temperature differences and the flow uniformity. The proposed design showed a greater flow resistance and similar heat exchanging capability than the existing parallel serpentine design. It has the advantage of a relatively wide low-temperature surface area, where the control circuit board susceptible to high temperatures can be located.

• Nuclear Engineering and Technology
• /
• v.24 no.2
• /
• pp.168-177
• /
• 1992

The importance of the study of two phase flow phenomena has increased for both fuel performance and safety analysis of nuclear power plants. In the analysis of two phase flow system, an accurate prediction of local void fractions is very important. In this study, a vertical rectangular subchannel having 4 electrically heated rods is constructed for the measurement of local void fraction under two phase flow. The measurement has been conducted by electrical conductivity probes and signal processing circuit which are known to be adequate to measuring local void fraction. Also experiments are performed with varying the inlet flow rate to search for radial void fraction profile accordingly to the different flow rate even with the same averaged void fraction. From the result of experiments, the validity of electrical conductivity probe and electrical circuit is confirmed.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.11
• /
• pp.1006-1012
• /
• 2007

In this paper, a suboptimal homing guidance law for the homing missiles with an impact angle constraint is presented. Unlike general LQ optimal control, the aided loop ensuring some degrees of freedom for the constraint is introduced. Then an optimal feedback loop in consideration of the aided loop is designed by using Schwartz inequality. The aided loop is synthesized with the optimal control to produce the guidance command. Furthermore, to investigate the characteristics of the guidance law we carry out the comparative studies with other guidance laws. The results of the various computer simulations show the good performance of the proposed law.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.12 no.3
• /
• pp.173-180
• /
• 1992

A feature typical of natural rivers is the bend. The purpose of this study is to examine hydraulic and morphometric characteristics in channel bend reach by the deterministic approach. Cross section shape factor, "As" is suggested for a new cahracteristic factor of channel bend reach analysis. The variation of this new factor along the river reach showed the location of the concentration of the force due to the current all over the reach, that is curved or not. Some general meander factors are used for correlation with new factor suggested, and the applicability of "As" is verified. The range R/W values are concentrated 2~4, the meanning of this value can be regarded to the warning for bank erosion or breaking. And this paper dealt with prediction of cross section bed shape variation.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.4
• /
• pp.36-42
• /
• 2004

The Properties of material, C18200 which is used for development of high performance liquid rocket engine combustor chamber were obtained by tension tests. The specimen for regenerative combustor was designed by structural analysis using that Properties. After the designed specimen was manufactured by the same manufacturing process of regenerative combustor. the yielding stress and yielding strain were obtained by strength tests. The properties of C18200 was degraded very much after brazing. The estimation of yielding pressure by structural analysis was almost same as that of strength test. The collector Part was yielded and failed previously than that of cooling channel part during strength test.

• Electrical & Electronic Materials
• /
• v.3 no.4
• /
• pp.332-338
• /
• 1990

본 연구는 절연유가 금속 파이프 중을 통과할 때 흐르는 유동전류 특성에 대하여 실험적으로 규명하였다. 유동전류는 파이프 길이, 절연유의 속도 및 온도에 따라 변하는 것이 관측되는데 파이프 길이가 4-6cm부근에서 피이크치가 나타나고 유속의 증가에 따라서는 선형적으로 증가하며 그리고 유의 온도가 약 50.deg.C 부근에서 또한 피이크가 나타나고 있다. 절연유에 전하를 주입시키는 수단으로 코로나 방전을 이용하였으며 부코로나 대전된 절연유의 유동전류가 코로나 대전 시키지 않은 절연유나 정코로나 대전된 절연유의 것보다 큰 값이 관측되었다. 이 결과로부터 고체 액체 접촉시 액체중의 음이온이 화학 포텐셜에 의하여 고체 표면에 흡착된다는 사실과 유동전류의 방향 및 발생기구를 해석할 수 있다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2019.05a
• /
• pp.568-569
• /
• 2019

20~30년 전부터 국내 지중송전선로에 OF(Oil Filled)케이블을 사용해 왔다. OF케이블은 오랜 시간동안 신뢰성을 화고하고 있으며, 전연파괴 사고를 미연에 방지할 수 있는 장점이 있지만 유지보수에 많은 어려움이 있고, 절연유에 의한 환경오염이 발생하며, 화재에 취약한 단점이 있다. 최근 20~30년 전에 설치된 OF케이블의 수명이 한계에 도달하면서 고장 위험성이 증가하고, 누유의 위험성이 도사리고 있다. 본 논문에서는 OF케이블 상태 진단방법에 있어서 절연유에 반응하는 필름센서를 활용하여 절연유 탱크의 연결부에서 누유현상을 감지하여 OF케이블 누유 관리시스템을 개발하자 한다.