• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.1
• /
• pp.51-57
• /
• 2016

This paper describes the physical layer modem structure of Giga KOREA 5G system which is being developed by ETRI as a 5G telecommunications prototype. The objective of Giga KOREA 5G system is supporting maximum 100 Gbps data rate for each cell with wide-bandwidth baseband station and mobile station prototypes in mmWave (10~40 GHz) environment. To achieve this objective, its physical layer is composed of high performance baseband station as well as mobile station and their OFDM TDD modems. The important features of Giga KOREA 5G physical layer are carrier aggregation, multiple receiving beam searching in mobile station, high data rate channel encoder and decoder and high speed modulation and demodulation functions.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.3A
• /
• pp.265-271
• /
• 2009

This paper proposes an efficient initial frequency estimator for Digital Video Broadcasting-Second Generation (DVB-S2). The initial frequency offset of the DVB-S2 is around ${\pm}5MHz$, which corresponds to 20% of the symbol rate at 25Msps. To estimate a large initial frequency offset, the algorithm which call provide a large estimation range is required. Through the analysis of the data-aided (DA) algorithms, we find that the Mengali and Moreli (M&M) algorithm can estimate a large initial frequency offset at low SNR. Since the existing frequency estimator based on M&M algorithm has a high hardware complexity, we propose the methods to reduce the hardware complexity of the initial frequency estimator. This can be achieved by reducing the number of autocorrelators and arctangents. The proposed architecture can reduce the hardware complexity about 64.5% compared to the existing frequency estimator and has been thoroughly verified on the Xilinx Virtex II FPGA board.

• Journal of Broadcast Engineering
• /
• v.10 no.3
• /
• pp.401-412
• /
• 2005

We propose and design the algorithms of symbol timing recovery, carrier recovery, and equalization for the receiver of S-DMT cable modem, which supports more channels and better symmetric mutimedia services over HFC network. We evaluate the performance of the concatenated entire receiving system of 16QAM, 64QAM in the mixed noise channel of AWGN, ISI and impulse. The result of evaluation shows those algorithms work correctly and designed S-DMT receiver has good performance. We also verify the designed system has excellent immunity against impulse noise channel of practical Cable TV networks by the result of simulation with the parameters of impulse internal $\varepsilon$ and noise power $\gamma^{k}$.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.3
• /
• pp.32-38
• /
• 2005

FBG sensors have been studied more actively than any other fiber optic sensor because of good multiplexing capabilities among many fiber optic sensors. The demodulation method of FBG sensors is based on the detection of wavelength shift of their sensor peaks and properties such as strain and temperature can be measured by detecting them. However, the signal stability of FBG sensors can be influenced by the strain gradient induced by structural geometry or cracks on the surface when FBG sensors are embedded into or attached on the structure. In this study, the signal characteristics of reflected spectra of FBG sensors under strain gradient were verified and the relations between the grating length of FBG sensors and the amount of strain gradient were investigated. From the experimental results, the recommended working range of FBG sensors under strain gradients was shown quantitatively with respect to grating lengths of them.

• Journal of Broadcast Engineering
• /
• v.15 no.1
• /
• pp.14-28
• /
• 2010

This paper considers technological requirements to broadcast digital television signals using distributed frequency network (DFN) in the advanced television systems committee (ATSC) transmission system and proposes distributed translator (DTxR) to meet such requirements. In the DFN, DTxR uses different frequency from main transmitter, but same among DTxRs. In addition, this paper introduces digital signal processing (DSP) techniques, which consist of demodulation, equalization, transmitter identification (TxID) generation and insertion, and modulation, to implement DTxR.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.10
• /
• pp.2039-2044
• /
• 2009

The PSK carrier signal recovery circuit using multi-layer coupled line was analyzed and designed. The fabricated carrier recovery 6 port element with multi-layer coupled line structure gets the simple architecture. It is possible to implement the carrier signal recovery circuit of the same structure with the multi-layer six port phase correlator of the direct receiver front-end. Based on the analysis of RML carrier recovery circuit using the multi-layer coupled line 6-port phase correlator, the multi-layer coupled line carrier signal recovery structure for multi-mode coherent demodulation was proposed. The fabricated multi-layer coupled line carrier signal recovery circuit for quadrature phase shift-keying shows a good carrier signal characteristic with a constant phase and phase error below ${\pm}3o$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.8
• /
• pp.1752-1758
• /
• 2010

A FM-CW radar is used for the various purposes as a remote sensing device since it has the advantages of the relatively simple implementation and the low probability of signal interception. A FM-CW radar uses the same frequency modulated continuous wave for both transmission and demodulation. Therefore, the received beat frequency represents the range and Doppler information of targets. However, using the conventional FFT method, the degree of accuracy and resolution in the spectrum estimation can be seriously degraded in the detection and tracking of fast moving targets because of the short dwell time. Therefore, in this paper, the model parameter estimation methods called as an autoregressive method is applied to overcome these problems and showed that the improved accuracy and resolution can be obtained for the target range and velocity estimation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.7
• /
• pp.1601-1607
• /
• 2009

As a general rule, the orthogonal modulation scheme which is widely used for wireless communications is not appropriate for the high speed data transmission applications due to the low bandwidth efficiency. Therefore, to increase the bandwidth efficiency of the conventional orthogonal modulation, we propose the multi-code trans-(bi-)orthogonal modulation in this paper. It is the combined scheme of multi-code modulation and trans-orthogonal modulation. We can know that the bandwidth efficiency of the proposed scheme is better than that of the conventional orthogonal modulation. Additionally, the receiver complexity of the proposed scheme is lower than that of the conventional orthogonal modulation. The proposed scheme can be used for the physical layer of the high speed wireless digital data transmission applications such as multimedia communications system and high speed personal area networks.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.5
• /
• pp.1045-1057
• /
• 1997

In this paper, we propose an algorithm of block synchronization that uses data withoug synchronization preambles. Block synchronization systems is implemented using the DSP chip employing the proposed algorithm. The data spread of the DFT blocks is proportional to the offset of DFT block and this information is used to achieve the block synchronization in the receiver. The initial bleock synchronization and the clock synchronization between transmitter and receiver are achieved using the early-late removal of the guard interval. The hardware implmentation is carried out using the DSP chip TM320C30 to verify the proposed block synchronization algorithm with the data rate 1200bps. The DSP chip calculates the spread of the 128 complex FFT in the receiver with the system clock 30MHz. It is believed that the proposed synchronization algorithm can be used in the design of OFDM block synchronization with the high processing DSP chip.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.10C
• /
• pp.1433-1443
• /
• 2004

The power line modem proposed in this paper transmits the remote control signal using CSK(Code Shift Keying) and DS/SS method. The CSK technique provides the increased capacity of transmission and robustness towards noise. Besides, the DS/SS technique provides protection against narrow-band Gaussian interference and multi-path interference. The modem supports full-duplex communication using FDD(Frequency Division Duplex) and the modem structure for forward link is same with that for reverse link. To switch each sub-controlled unit smoothly, 4/$\pi$-DQPSK is adopted for noncoherent demodulation. The PN code for spreading spectrum seues to divide each group which consists of sub-controlled units and Walsh code is used for the M-ary CSK technique. Each block is designed and verified with TMS320C5402 DSP. We show the superiority of the proposed method by analyzing numerically the system performance for the factors of the DS/SS and CSK method ullder additive white Gaussian noise and PBI.