• Aerospace Engineering and Technology
• /
• v.6 no.1
• /
• pp.173-181
• /
• 2007

Radiated emission / susceptibility performance of the KSLV-I 2nd stage which are controlled from the unit level to the system level should be examined and managed all over the frequency ranges in order to ensure the normal operation of the SC, the 1st stage of the KSLV-I, ground support equipments which are installed at the space center, and other wireless communication networks. Not only unintentional electric field emissions from the KSLV-I system and its subsystems should be restricted to the levels less than the limits specified in the EMC requirements, but also proper test and evaluation method should be established, respectively. In this paper, radiated emission/susceptibility test limits, method, and test results of the KSLV-I 2nd stage engineering model are presented.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.12
• /
• pp.1272-1278
• /
• 2009

The cancellation method of P/G(power/ground) plane resonances which are generated between the power plane and the ground plane in a 4-layer PCB(Printed Circuit Boards) with a via-hole for the improvement of the RE(Radiated Emission) characteristic is presented. The validity of the proposed method was confirmed from simulation and measurement of performances of signal transmission characteristic, intensities of edge-radiation and radiated emission of PCB with a via-hole.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.12 s.115
• /
• pp.1189-1198
• /
• 2006

We analyze the radiated emission and mutual coupling problem from a single microstrip transmission line and double signal traces with various ground patterns. In this paper, it is shown that the reduction of the radiated emission from the signal traces can be accomplished by using the novel and compact patterns on the ground planes in a specific frequency band. The accuracy and validation of radiation mechanism from the transmission line on a novel ground plane are evaluated and explained by using a commercially available software and experiment, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.3
• /
• pp.336-344
• /
• 2011

The purpose of this study is to analyze the radiation-pattern characteristics above 1 GHz for the electromagnetic wave radiated from multi-slot such as ventilations, etc. on the enclosure of an EUT and so to make recommendations for suitable test methods. An experimental EUT was formed by putting a comb-generator at the center of a rectangular enclosure with 4 slots, and its radiation pattern was analyzed in the frequency range of 1~6 GHz. As analysis results, multi-lobe appears above 2 GHz and the number of multi-lobes is growing as the frequency increases. And real radiated-emission measurements were performed for the experimental EUT by scanning a receiving antenna in the height of 1~4 m and tilting toward maximum radiation, as well as setting the height of a receiving antenna to the central position of the EUT which is prescribed at the present standards. The measured results are +12.8 dB in the scanning and +16.4 in the scanning and tilting compared with the present standard test method. Therefore, the latter must be revised in order to consider the radiation pattern above 1 GHz.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.10
• /
• pp.878-883
• /
• 2014

This paper presents the test result of system level EMC of LEO satellite Deimos-2 FM that has been launched in June 20, 2014. The Deimos-2 satellite was designed considering the EMC of unit modules level in addition to the structure aspects. The Auto-Compatibility, Radiated Emission and Radiated Susceptibility test was conducted. The test result has meet the standard of system EMC of Deimos-2 program.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.3
• /
• pp.291-298
• /
• 2016

In this paper, we studied about the radiated emission of EFT(Electrical Fast Transient)/Burst signal, referenced IEC-61000-4-4 of the international EMC standard and its effect on EUT(Equipment Under the Test) when EFT/Burst signal (Conducted noise) induced on a power cable to EUT. Firstly, we set up test sample by the standard and +4 kV standard signal is induced by EFT/Burst signal generator with 1 m length power cable for 1 minute. Consequently, we found not only induced EFT/Burst signal along power line, but also directly radiated emission signal from EFT/Burst signal generator (Radiated emission noise of EFT/Burst). The radiated emission signal of EFT/Burst was 30 dB which is higher than limit of CISPR 22 which is international EMC standard. Moreover, we measured the electric field strength by changing distance from maximum radiated emission point to electric field strength tester. As a result, this electric field strength was 23 V/m which is higher than international EMC standard test level(CISPR 24). Therefore, it was confirmed that the probability of malfunction may be high when radiated emission of EFT/Burst noise exists near the EUT.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1442-1443
• /
• 2008

본 논문에서는 인쇄회로기판과 도전체 샤시(Chassis)가 연결되었을 때의 복사성 방사(Radiated Emission)의 감소에 대해서 연구하였다. Current Driven 메커니즘 등가회로를 사용하여 전자파 방사의 주요한 원인중 하나인 Common-mode Current를 인쇄회로기판과 Chassis가 연결된 구조에 적용하였다. Chassis의 유무에 따라 복사성 방사의 감소를 확인하고자 2-layer 인쇄회로기판과 SECC(Steel Electro galvanized Cold-rolled Coil) 재질의 Chassis를 나사(Screw)를 통하여 전기적으로 연결하였을 때를 시뮬레이션 하였고, 제작된 구조물을 3m 무반향실에서 복사성 방사를 측정한 후 시뮬레이션과 결과를 비교하였다. 결과로 30MHz$\sim$45MHz에서 최대 10dB 감소의 효과가 있음을 확인하였다.

• Aerospace Engineering and Technology
• /
• v.6 no.1
• /
• pp.222-229
• /
• 2007

Environmental tests should be carried out to show that design performance is in an operational condition in an actual operational environment to assure maintainability and reliability. Aero-products electromagnetic compatibility tests are performed mainly for the individual parts and Specifications MIL-STD-461E and RTCA DO-160E are developed for the military and commercial parts tests respectively. The MIL-STD-461E which is a military environmental test standard is targeting all munitions and that user can apply by selecting applicable requirements from this specification. On the other hand, requirements are applied exclusively for the Avionics Equipments in commercial test standard.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.6 no.5
• /
• pp.643-648
• /
• 2011

In this study, SMPS driven LED traffic signal light for Large-scale traffic such as railroad and airport was designed and its electrical and EMI characteristics were measured. The output current of the LED module driven by SMPS was 1.67A for AC and DC input voltage over 10V. The conducted emission measured over 0.15~30MHz frequency range was lower than the allowed quasi-peak and average level, and the radiated noise measured over 30~1000MHz frequency range showed $23.96dB{\mu}V/m$ at 59.96MHz.

• Aerospace Engineering and Technology
• /
• v.2 no.1
• /
• pp.153-163
• /
• 2003

Electronic equipments and make other electronic systems to operate abnormally by means of electromagnetic interference, or can operate abnormally themselves by electromagnetic interference of other electronic systems. Therefore, electronic equipments are required to reduce their electromagnetic interference as small as for other systems to operate properly and operate properly within electromagnetic interference from other electronic systems. In order to prove that electronic equipments meet such requirements, they should undergo electromagnetic environmental test. In this study, we introduce electromagnetic environmental requirements, test procedures and test results of gimbal engine actuation system of KSR-III.