• Journal of Cadastre & Land InformatiX
• /
• v.46 no.2
• /
• pp.183-196
• /
• 2016

Ground control points are needed for precision geometric correction of satellite images, and the coordinates of a high-quality ground control point can be obtained from the GPS measurement. However, considering the GPS measurement requires an excessive amount o f t ime a nd e fforts, there is a need for coming up with an alternative solution to replace it. Therefore, we examined the possibility of replacing the existing GPS measurement with coordinates available at online maps to acquire the coordinates of ground control points. To this end, we examined error amounts between the coordinates of ground control points obtained through Daum Map API, and them compared the accuracies between three types of coordinate transformation equations which were used for geometric correction of satellite images. In addition, we used the coordinate transformation equation with the highest accuracy, the coordinates of ground control point obtained through the GPS measurement and those acquired through D aum M ap A PI, and conducted geometric correction on them to compare their accuracy and evaluate their effectiveness. According to the results, the 3rd order polynomial transformation equation showed the highest accuracy among three types of coordinates transformation equations. In the case of using mid-resolution satellite images such as those taken by Landsat-8, it seems that it is possible to use geometrically corrected images that have been obtained after acquiring the coordinates of ground control points through Daum Map API.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.32 no.5
• /
• pp.296-306
• /
• 2020

It has been reported that the wave heights measured by Wave and Tide gauges (WTG) have been underestimated, and thus it is important to improve its measuring accuracy for enhancing estimation of harbor tranquility. In this study, the significant wave heights from WTG were calibrated using measured data from AWAC and Waverider buoys moored at the same four locations with the WTG. It was observed that the product of significant wave height and peak wave period, HT, was not underestimated but linearly proportional between the measurements by two instruments. This linearity was applied to develop 3^rd order polynomial functions that best represented the relationship between HT and significant wave heights measured by WTG. These functions were then applied to calibrate the WTG significant wave heights that were lower than 0.7 m, the critical value established for the low waves in this study. The results showed that the linearity between the AWAC (or Waverider buoy) and calibrated wave heights were improved, and the magnitude of underestimated WTG wave heights were increased to be more realistic. The results of this study are expected to be effectively applied for other data sets obtained by WTG only, to increase the observation accuracy of WTG and to improve the estimation of harbor tranquility.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.10
• /
• pp.100-106
• /
• 2019

Ground and high altitude simulated combustion experiments were conducted using a liquid rocket engine with hydrogen peroxide and kerosene as the propellant. A ground and high altitude simulated combustion test facility was constructed by installing a high altitude model diffuser and TMS (Thrust Measuring System) on a vertical combustion test bench. The thrust characteristics according to altitude were investigated using the combustion test equipment. The diffuser was designed on a 1:4.8 scale to verify the characteristics of the high diffusing diffuser and starting pressure. The cold flow tests were conducted using nitrogen gas, and the performance characteristics and starting characteristics of the scale down diffuser were verified. A diffuser and TMS were installed on the vertical combustion test bench, and the thrust correction equations for the system resistance were derived. The thrust correction equations were derived from the step test and vacuum step test before the actual hot firing test. Nozzles with an operating altitude of 10km were designed. Hot firing tests were conducted to analyze the thrust characteristics according to the operating altitude changes. The actual thrust was calculated using each correction equation with the thrust value measured by the TMS.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.7 no.1
• /
• pp.37-48
• /
• 1989

Electronic Distance Meter(EDM) is widely used for the traverse surveying and trilateration net recently, therefore, the study on reliability of EDM is very important. In this study, the reliability of EDM is examined by calculating the distortion of traverse surveying net, statistically analyzing the results of side length between triangulation and trilateration. As the result of this study, correction equation of EDM and steel-tape is obtained. And also, linear regression equations with correlation coefficient (0.89-0.98) show resulting from the error analysis of each side length. In addition to checking the distortion of traverse surveying net, distortion calculated with correction EDM appears to be the smallest value.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.32 no.6
• /
• pp.458-464
• /
• 2020

Calibration of load-resistance factors for the limit state design of perforated caisson breakwaters are presented. Reliability analysis of 12 breakwaters in nationwide ports was conducted. Then, partial safety factors and load-resistance factors were sequentially calculated according to target reliability index. Load resistance factors were optimized to give one set of factor for limit state design of breakwater. The breakwaters were redesigned by using the optimal load resistance factor and verified whether reliability indices larger than the target value. Finally, some load-resistance factors were proposed by changing target reliability index.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.2
• /
• pp.177-182
• /
• 2015

General method for correcting the distortion caused by the characteristic of the fish-eye lens may be classified in two ways. The first method is a calibration method using a mathematical model taking into account the characteristics of the lens, the second method is a method using only the distortion correction image, regardless of the lens. When considering the characteristics of the lens, calibration equation can be calculated geometrically from the relationship between the three-dimensional real-world coordinates and two-dimensional image coordinates and the parameters of lens. However, it is not suitable for ellipsoid type lens, because of existing research papers have been corrected on the spherical-type fisheye lens. In this paper, we propose a method for correcting geometrically using fish-eye lens as an ellipsoid model. Through a calibration picture, it can be seen that the proposed method is valid.

• Journal of Korea Water Resources Association
• /
• v.52 no.9
• /
• pp.589-601
• /
• 2019

Various applications of radar rainfall data have been actively employed in the field of hydro-meteorology. Since radar rainfall is estimated by using predefined reflectivity-rainfall intensity relationships, they may not have sufficient reproducibility of observations. In this study, a generalized linear model is introduced to better capture the Z-R relationship in the context of bias correction within a Bayesian regression framework. The bias-corrected radar rainfall with the generalized linear model is more accurate than the widely used mean field bias correction method. In addition, we analyzed variability of the bias correction parameters under various geomorphological conditions such as the height of the weather station and the separation distance from the radar. The identified relationship is finally used to derive a regionalized formula which can provide bias correction factors over the entire watershed. It can be concluded that the bias correction parameters and regionalized method obtained from this study could be useful in the field of radar hydrology.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2018.05a
• /
• pp.41-41
• /
• 2018

하천과 저수지의 수질을 예측하고 관리하는데 수리 수질예측모형이 널리 활용되고 있다. 수질예측모형은 유역이나 수체 내의 오염물질 이동경로나 농도를 수치해석 방법으로 계산하여 사용자가 필요로 하는 지점과 시점에서의 수질자료 생산하는데 활용되고 있다. 수질예측모형은 검 보정을 통해 정확도를 확보하며, 정확도의 확보를 위해서는 높은 수준의 전문성을 필요로 한다. 특히 시행착오법으로 모형을 보정하는 경우 많은 시간과 노력을 필요로 하게 되며, 보정계수를 과대 혹은 과소로 모형에 적용하는 오류를 범하기 쉽고 모델러의 주관이 관여되기 쉽다. 그래서 본 연구에서는 CE-QUAL-W2모형의 조류항목에 대한 모형 보정을 위하여 Chl-a와 남조류세포수에서 주로 활용되고 있는 보정계수에 대한 민감도 분석 결과를 토대로 매개변수별 모의결과 변화율을 산정하였으며, 시기적 경향성을 재현하기 위해 Ensemble-Bagging 기법과 머신 러닝 기법을 적용하여 모형 구동횟수를 최소화 할 수 있는 방법으로 구성하였다. Chl-a를 보정하기 위한 매개변수는 9개를 선정하였으며, 규조류, 남조류, 녹조류에 총 27개 매개 변수를 민감도 분석으로 도출 한 후 예상 변화율 대비 이벤트별 모의치와 실측치 간 %difference가 유사하도록 매개변수를 조정하였다. 또한 각 이벤트 조합의 매개변수 빈도수와 매개변수별 예상변화율, 시기적 조류특성을 고려하여 가중치를 도출하였으며, 1회 보정에 맞춰 Chl-a 모델 실행결과를 %difference로 평가한 후 "good"등급을 만족할 때까지 반복 적용하였다. 남조류세포수의 경우 Chl-a에 맞춰 매개변수 최적화 이후 남조류세포수 농도를 세포수로 환산하기 위한 CACEL에 대해 머신러닝 기법을 적용하였으며, CACEL 추정변화율 회귀식에 따라 평가 한 후 %difference "good"등급 이상을 만족할 때까지 반복 수행하는 방법을 적용하였다. 본 연구에서는 수질예측모형의 정확도를 확보하기 위하여 최적화 기법을 적용하였으며, 이를 통해 모형을 보정하는 과정에서 요구되는 시간과 노력을 줄일 수 있도록 하였으며, Ensemble기법과 머신러닝 기법을 적용하여 모형보정계수 적용에 객관성을 확보할 수 있도록 하였다.

• Proceedings of the Korean Information Science Society Conference
• /
• 2002.10e
• /
• pp.406-408
• /
• 2002

TFRC 혼잡제어는 멀티미디어, 인터넷 전화등 실시간성이 강조된 서비스에 적합한 프로토콜이다. 그러나 이러한 TCP-friendly 혼잡제어 알고리즘은 네트워크 혼잡이 심해져 손실률이 커짐에 따라 TCP와의 공정성(fairness)이 떨어지는 문제점을 가지고 있다. 이러한 문제를 해결하기 위해서는 전송률을 결정하는 제어식을 높은 손실률일 때 보정을 해주어야 한다. 본 논문에서는 TFRC 혼잡제어 알고리즘의 전송률 결정에 있어서 중요한 변수인 재전송 타임아웃 값(RTO)의 재 정의를 통하여 전송률을 보정함으로서 공정성 하락을 방지함을 보이고, 시뮬레이션을 통하여 이를 입증한다.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.11 no.5
• /
• pp.93-99
• /
• 2002

In general, manufacturing error is originated from bad material, machine tool defection and tool breakage. When the manufacturing process is stable, the most of error come from the tool wear. In common on-machine measurement teaching probe and touch sensor are widely used however in this paper the electric touch point type automatic tool compensation system is developed the performance of it is validated and effective operating is proposed.