• Journal of the Korea Concrete Institute
• /
• v.25 no.6
• /
• pp.649-656
• /
• 2013

Coupled shear walls can provide an efficient structural system to resist lateral force. However, the reinforcement detail for diagonally reinforced coupling beams required by ACI-318 often causes the difficulties in construction due to the reinforcement congestion and interference among reinforcement. This paper is to evaluate cyclic behavior of High-Performance Fiber-Reinforced Cement Composite (HPFRCC) coupling beams having reduced transverse reinforcement around the beam perimeter. Experimental test was conducted using three specimens having a beam aspect ratio 2.0. Test results showed that HPFRCC coupling beams with half of transverse reinforcement required by ACI-318 provided similar energy dissipation capacities compared with the coupling beams having reinforcement satisfy the requirement of ACI-318.

• Magazine of the Korea Concrete Institute
• /
• v.9 no.1
• /
• pp.44-59
• /
• 1997

• Proceeding of EDISON Challenge
• /
• 2015.03a
• /
• pp.191-196
• /
• 2015

해상 pedestal 크레인은 각종 운송물을 선박에 싣거나 내리는 해상 운송에 필수적인 장비이다. 따라서 구조적 안전성을 가지는 크레인 설계가 요구된다. 그의 일환으로 수행된 '해상 pedestal 크레인의 설계 개선을 위한 연구'에서는 기존 크레인의 기초 설계에 대해서 구조적 안전성올 평가하여 개선 방안을 제시하였다. 또한 좌굴 안정성 향상을 위한 보강재 설계를 수행하였다. 하지만 상세설계 관점에서 미비한 점이 있어 이를 보완할 필요성이 있다. 안전성 평가를 위해 필요한 응력을 계산하기 위해 EDISON-CSD프로그램을 통해 유한요소모델 해석을 활용한 구조해석을 수행하였다. 효율적인 해석을 위해 상세설계에 필요한 부분영역을 선택하여 모델링 하였으며 전체영역에서의 해석 결과 값을 등가 힘, 등가 모멘트로 환산하여 경계조건으로 부여하였다. 보강재간의 교차점 형상이 안전성에 미치는 영향을 보기위해 stiffener와 diaphragm의 교차점 형상(반원, 정사각형, 사다리꼴)에 따라 안전성 평가를 수행하였고, 안전 여유의 유효한 차이를 보이지 않음을 확인하였다. 평가에 필요한 응력계산을 위해 또한 Diaphragm의 좌굴에 대한 영향을 고려하기 위해 설계 규격 DNV-RP-201 8장(Buckling of girders)을 분석하였고, 안전성 평가에 반영하였다. 또한 실제 현장에서 보편적으로 사용되는 angle 형상 stiffener의 치수 도출을 위해 최적설계를 수행하였고, 모든 설계 제한조건을 만족하면서 최소의 무게를 가지는 합리적인 치수를 도출하였다.

• Journal of the Korea Concrete Institute
• /
• v.14 no.4
• /
• pp.578-588
• /
• 2002

An experimental study was conducted to investigate the effectiveness of transverse reinforcement in reinforced concrete tied columns subjected to monotonically increasing axial compression. Eighteen large-scale columns(260$\times$260$\times$1200 mm) were tested. Effects of main variables such as the concrete compressive strength, the tie configuration, the transverse reinforcement ratio, the tie spacing, and the spatting of the concrete cover were considered. High-strength concrete columns under concentric axial loads show extremely brittle behavior unless the columns are confined with transverse reinforcement that can provide sufficiently high lateral confinement pressure There is a consistent decrease in deformability of column specimen with increasing concrete strength. Test results were compared with the previous confinement model such as modified Kent-Park, Sheikh-Uzumeri, Mander, and Saatcioglu-Razvi model. The comparison indicates that many previous models for confined concrete overestimate or underestimate the ductility of confined concrete.

• Journal of the Korea Concrete Institute
• /
• v.27 no.5
• /
• pp.541-549
• /
• 2015

This study was conducted to experimentally investigate the seismic retrofitting performance of non-ductile reinforced concrete (RC) frames by introducing engineered cementitious composite (ECC) wing panel elements. Non-ductile RC frame tested in this study were designed and detailed for gravity loads with insufficient or no consideration to lateral loads. Therefore, Non-ductile RC frame were not satisfied on present seismic code requirements. The precast ECC wing panels were used to improve the seismic structural performance of existing non-ductile RC frame. A series of experiments were carried out to evaluate the structural performance of ECC wing panel elements alone a non-ductile RC frame strengthened by adding ECC panel elements. Failure pattern, strength, stiffness and energy dissipation characteristics of specimens were evaluated based on the test results. The test results show that both lateral strength and stiffness were significantly improved in specimen strengthened than non-ductile RC frame. It is noted that ECC wing wall elements application on non-ductile RC frame can be effective alternative on seismic retrofit of non-ductile building.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.19 no.1
• /
• pp.62-71
• /
• 2015

KCI 2012 and ACI318-11 contains development length provisions for the use of headed deformed bars in tension and does not allow their tension lap splices. In ACI318-11, the confinement factor, such as transverse reinforcement factor, is not used to calculate the development length of headed bars. The purpose of this experimental study is to evaluate the effect of confinement details to the lap splice performance of headed deformed reinforcing bars in grade SD400 and SD500. The confinement details are stirrups and tie-down bars in lap zone. Test results showed that specimens with only stirrups had the brittle failure and could not increase lap strengths, and that specimens with composite confinements by stirrups and tie-down bars had the flexural strengths over than nominal flexural strengths. Stirrups with tie-down bars can have an effect on improvement in lap splice of headed bars in grade SD400 and SD500.

• Magazine of the Korea Concrete Institute
• /
• v.9 no.1
• /
• pp.29-35
• /
• 1997

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.2
• /
• pp.49-57
• /
• 2021

A study was conducted to secure structural performance as well as improve workability by improving the reinforcement details of special shear wall and coupling beams. Based on the specimen in which the existing diagonal bundle reinforcement and shear reinforcement were placed, the specimens replaced with thick diagonal reinforcing bars and the specimens replaced with horizontal reinforcing bars were selected as variables. As a result of the experiment, the specimen, which replaced the existing diagonal reinforcement with a thick-diameter reinforcement, showed a similar behavior to that of the basic specimen, and it was evaluated that it can be applied as an alternative to the details.

• Journal of the Korea Concrete Institute
• /
• v.25 no.4
• /
• pp.447-455
• /
• 2013

In this study, reinforced concrete slabs with steps were experimentally studied to analyze their structural performance and to suggest reinforcing details in the step. Because the stepped slabs may behave very poorly in terms of bending strength, stiffness, deflection, cracking, etc., the study is aimed to suggest proper reinforcing details such that the same bending strength is obtained as that without steps. The bending strengths of 12 test specimens with a variety of different reinforcing detail types or other parameters were compared with each other. The specimen without any additional reinforcement in the step had a very low bending strength and significant damage, and the specimens with diagonal reinforcements in the step showed substantial early cracks, experienced hinging of the step, and had a substantial loss of the bending strength. In contrast, the specimens with a combination of U-bars, reversed U-bars, L-bars, and reversed L-bars performed very well and almost reached to 100% of the slab bending strength. The U-bars and reversed U-bars were effective in controling the diagonal cracks, while the L-bars and reversed L-bars were effective in preventing from yielding of slab reinforcement near the step.

• Journal of the Korea Concrete Institute
• /
• v.22 no.3
• /
• pp.357-366
• /
• 2010

This paper presents experimental results about shear wall with various lateral reinforcement details in boundary elements. The research objective is to study the structural behavior of shear wall with boundary column confined by rectangular spiral hoops and headed cross ties developed to improve workability in the fabrication of boundary columns. These two details can be fabricated in a factory and put together on-site after being delivered so that the construction work may be reduced. Main parameters in the experimental study were the types of hoop and cross tie: rectangular spiral hoop and headed cross tie vs. standard hoop and cross tie with hook. Four half scaled shear wall specimens with babel shape were made and tested by applying horizontal cyclic load under constant axial force, 10% of nominal compressive strength of concrete. Based on the test result, it was shown that the shear wall with rectangular spiral hoop and headed cross tie in boundary columns has structural capacity compatible with conventional shear wall. The specimen SW-Hh which has bigger hoop bar and higher volumetric ratio of transverse reinforcements than other showed improved energy dissipating characteristic but it presented a rapid reduction of strength after peak point. The results indicates that, it is necessary to consider volumetric ratio of transverse reinforcements as well as hoop space in designing of shear wall with boundary columns for improved strength and ductility.