• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.8
• /
• pp.25-32
• /
• 2011

Networks-on-chip (NoC) is emerging as a key technology to overcome severe bus traffics in ever-increasing complexity of the Multiprocessor systems-on-chip (MPSoC); however traditional electrical interconnection based NoC architecture would be faced with technical limits of bandwidth and power consumptions in the near future. In order to cope with these problems, a hybrid optical NoC architecture which use both electrical interconnects and optical interconnects together, has been widely investigated. In the hybrid optical NoCs, wormhole switching and simple deterministic X-Y routing are used for the electrical interconnections which is responsible for the setup of routing path and optical router to transmit optical data through optical interconnects. Optical NoC uses circuit switching method to send payload data by preset paths and routers. However, conventional hybrid optical NoC has a drawback that concurrent transmissions are not allowed. Therefore, performance improvement is limited. In this paper, we propose a new routing algorithm that uses circuit switching and adaptive algorithm for the electrical interconnections to transmit data using multiple paths simultaneously. We also propose an efficient method to prevent livelock problems. Experimental results show up to 60% throughput improvement compared to a hybrid optical NoC and 65% power reduction compared to an electrical NoC.

• 전자공학회논문지 IE
• /
• v.47 no.4
• /
• pp.18-27
• /
• 2010

This paper is designed the efficient Data Acquisition System for an vibration of rotatory machines. The Data Acquisition System is consist of the analog logic having signal filer and amplifier, and digital logic with ADC, DSP, FPGA and FIFO memory. The vibration signal of rotatory machines acquired from sensors is controlled by the FPGA device through the analog logic and is saved to FIFO memory being converted analog to digital signal. The digital signal process is performed by the DSP using the vibration data in FIFO memory. The vibration factor of the rotatory machinery analysis and diagnosis is defined the RMS, Peak to Peak, average, GAP, FFT of vibration data and digital filtering by DSP, and is need to follow as being happened the event of vibration and make an application to an warning system. It takes time to process the several analysis step of all vibration data and the event follow, also special event. It should be continuously performed the data acquisition and the process, however during processing the input signal the DSP can not be performed to the acquisited data after then, also it will be lose the data at several channel. Therefore it is that the system uses efficiently the DSP and FPGA devices for reducing the data lose, it design to process a part of the signal data to FPGA from DSP in order to minimize the process time, and a process to parallel process system, as a result of design system it propose to method of faster process and more efficient data acquisition system by using DSP and FPGA than signal DSP system.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.3
• /
• pp.59-67
• /
• 2013

Reed-Solomon (RS) codes are powerful error-correcting codes used in diverse applications. Recently, algebraic soft-decision decoding algorithm for RS codes that can correct the errors beyond the error correcting bound has been proposed. The algorithm requires very intensive computations for interpolation, therefore an efficient VLSI architecture, which is realizable in hardware with a moderate hardware complexity, is mandatory for various applications. In this paper, we propose an efficient architecture with low hardware complexity for interpolation in soft-decision list decoding of Reed-Solomon codes. The proposed architecture processes the candidate polynomial in such a way that the terms of X degrees are processed in serial and the terms of Y degrees are processed in parallel. The processing order of candidate polynomials adaptively changes to increase the efficiency of memory access for coefficients; this minimizes the internal registers and the number of memory accesses and simplifies the memory structure by combining and storing data in memory. Also, the proposed architecture shows high hardware efficiency, since each module is balanced in terms of latency and the modules are maximally overlapped in schedule. The proposed interpolation architecture for the (255, 239) RS list decoder is designed and synthesized using the DongbuHitek $0.18{\mu}m$ standard cell library, the number of gate counts is 25.1K and the maximum operating frequency is 200 MHz.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.12
• /
• pp.20-35
• /
• 2016

In this paper, in order to reduce the delay and area of the partial product accumulation (PPA) of the parallel decimal multiplier, a tree architecture that composed by multi-operand decimal CSAs and improved CLA is proposed. The proposed tree using multi-operand CSAs reduces the partial product quickly. Since the input range of the recoder of CSA is limited, CSA can get the simplest logic. In addition, using the multi-operand decimal CSAs to add decimal numbers that have limited range in specific locations of the specific architecture can reduce the partial products efficiently. Also, final BCD result can be received faster by improving the logic of the decimal CLA. In order to evaluate the performance of the proposed partial product accumulation, synthesis is implemented by using Design Complier with 180 nm COMS technology library. Synthesis results show the delay of the proposed partial product accumulation is reduced by 15.6% and area is reduced by 16.2% comparing with which uses general method. Also, the total delay and area are still reduced despite the delay and area of the CLA are increased.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.3
• /
• pp.164-173
• /
• 2014

In underwater robotics, vision would be a key element for recognition in underwater environments. However, due to turbidity an underwater optical camera is rarely available. An underwater imaging sonar, as an alternative, delivers low quality sonar images which are not stable and accurate enough to find out natural objects by image processing. For this, artificial landmarks based on the characteristics of ultrasonic waves and their recognition method by a shape matrix transformation were proposed and were proven in Part 1. But, this is not working properly in undulating and dynamically noisy sea-bottom. To solve this, we propose a framework providing a selection phase of likelihood candidates, a selection phase for final candidates, recognition phase and tracking phase in sequence images, where a particle filter based selection mechanism to eliminate fake candidates and a mean shift based tracking algorithm are also proposed. All 4 steps are running in parallel and real-time processing. The proposed framework is flexible to add and to modify internal algorithms. A pool test and sea trial are carried out to prove the performance, and detail analysis of experimental results are done. Information is obtained from tracking phase such as relative distance, bearing will be expected to be used for control and navigation of underwater robots.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.6
• /
• pp.188-198
• /
• 2013

In order to increase its performance, NAND flash memory-based storage is composed of data buses that are shared by a number of flash memories and uses a parallel technique that can carry out multiple flash memory operations simultaneously. Since the storage performance is strongly influenced by the performance of each data bus, it is important to improve the utilization of the bus by ensuring effective scheduling of operations by the storage controller. However, this is difficult because of dynamic changes in buses due to the unique characteristics of each operation with different timing, cost, and usage by each bus. Furthermore, the scheduling technique for increasing bus utilization may cause unanticipated operation delay and wastage of storage resource. In this study, we suggest various dynamic operation scheduling techniques that consider data bus performance and storage resource efficiency. The proposed techniques divide each operation into three different stages and schedule each stage depending on the characteristics of the operation and the dynamic status of the data bus. We applied the suggested techniques to the controller and verified them on the FPGA platform, and found that program operation decreased by 1.9% in comparison to that achieved by a static scheduling technique, and bus utilization and throughput was approximately 4-7% and 4-19% higher, respectively.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.3 s.345
• /
• pp.59-67
• /
• 2006

OFDM (Orthogonal frequency Division Multiplexing) systems convert serial data stream to N parallel data streams and modulate them to N orthogonal subcarriers. Thus spectrum utilization efficiency of the OFDM systems are high and high-speed data transmission is possible. However, with the OFDM systems using the same modulation method at all subcarriers, the error probability is dominated by the subcarriers which experience deep fades. Therefore, in order to enhance the performance of the system adaptive modulation is required, with which the modulation methods of the subcarriers are determined according to the estimated SNRs. The IEEE 802.11a system selects various transmission speed between 6 and 54 Mbps according to the modulation mode. There are three typical methods for SNR estimation: Direct estimation method uses the frequency domain symbols to estimate SNR directly by minimizing MSE (Mean Square Error), EVM method utilizes the distance between the demodulated constellation points and received complex values, and the method utilizing the Viterbi algorithm uses the cumulative minimum distance in decoding process to estimate the SNR indirectly. Through comparison analyses of three methods we propose a new SNR estimation method, which employs both the EVM method and the Viterbi algorithm. Finally, we perform extensive computer simulations to confirm the performance improvement of the proposed adaptive OFDM systems on the basis of IEEE 802.11a.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.7
• /
• pp.48-56
• /
• 2011

Recently, new storage device SSD(Solid State Disk) based on NAND flash memory is gradually replacing HDD(Hard Disk Drive) in mobile device and thus a variety of research efforts are going on to find the cost-effective ways of performance improvement. By increasing the NAND flash channels in order to enhance the bandwidth through parallel processing, DRAM buffer which acts as a buffer cache between host(PC) and NAND flash has become the bottleneck point. To resolve this problem, this paper proposes an efficient low-cost scheme to increase SSD performance by improving DRAM buffer bandwidth through scheduling techniques which utilize DRAM multi-banks. When both host and NAND flash multi-channels request access to DRAM buffer concurrently, the proposed technique checks their destination and then schedules appropriately considering properties of DRAMs. It can reduce overheads of bank active time and row latency significantly and thus optimizes DRAM buffer bandwidth utilization. The result reveals that the proposed technique improves the SSD performance by 47.4% in read and 47.7% in write operation respectively compared to conventional methods with negligible changes and increases in the hardware.

• Korean journal of applied entomology
• /
• v.35 no.3
• /
• pp.260-265
• /
• 1996

A field colony of the two-spotted spider mite, Tetranychus urticae Koch, was selected with tetradifon for 4 mousing whole-plant residual method. This strain showed 371-fold resistance to tetradifon. The log dosehatchability lines of $F_{1}$ eggs(RS cross; Td5female$\times$Smale, and SR cross; Sfemale$\times$Td5male) were closer to the line of the resistant colony than to that of the susceptible. These differences could be due to cytoplasmic inheritance or maternal effect. The estimate of dominance index (D) for the $F_{1}$ eggs of RS cross was 0.998 and that for $F_{1}$ eggs of SR cross was 0.262. This indicates that tetradifon resistance is completely dominant in RS cross and incompletely dominant in SR cross. Td5 strain exhibited high levels of resistance to clofentezine, benzoximate, and chlorfencon, and no cross resistance to fenazaquin, pyridaben, flufenoxuron, tebufenpyrad, and fenothiocarb.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.6
• /
• pp.447-458
• /
• 2003

A high speed multiplier is essential basic building block for digital signal processors today. Typically iterative algorithms in Signal processing applications are realized which need a large number of multiply, add and accumulate operations. This paper describes a macro block of a parallel structured multiplier which has adopted a 32$\times$32-b regularly structured tree (RST). To improve the speed of the tree part, modified partial product generation method has been devised at architecture level. This reduces the 4 levels of compression stage to 3 levels, and propagation delay in Wallace tree structure by utilizing 4-2 compressor as well. Furthermore, this enables tree part to be combined with four modular block to construct a CSA tree (carry save adder tree). Therefore, combined with four modular block to construct a CSA tree (carry save adder tree). Therefore, multiplier architecture can be regularly laid out with same modules composed of Booth selectors, compressors and Modified Partial Product Generators (MPPG). At the circuit level new Booth selector with less transistors and encoder are proposed. The reduction in the number of transistors in Booth selector has a greater impact on the total transistor count. The transistor count of designed selector is 9 using PTL(Pass Transistor Logic). This reduces the transistor count by 50% as compared with that of the conventional one. The designed multiplier in 0.25${\mu}{\textrm}{m}$ technology, 2.5V, 1-poly and 5-metal CMOS process is simulated by Hspice and Epic. Delay is 4.2㎱ and average power consumes 1.81㎽/MHz. This result is far better than conventional multiplier with equal or better than the best one published.