• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.1
• /
• pp.19-28
• /
• 2016

In the case of structural analysis for building structures, the super-structure and the sub-structure are analyzed by using separate structural models in the field because of time saving, facile result interpretation and easy analysis of dynamic behavior. However this separate structural model violated the compatibility condition of structural analysis and it can not consider the interaction of superand sub- structures. In the present study, the analysis results of this separate model were compared to those of the unified model of super- and sub- structures which can consider the interaction of super- and sub- structures and reflect the realistic boundary conditions. According to the comparison results, the the analysis model using separate models can underestimate the member force and deflection of structural members in the super-structures and overestimate the deflection and member force of sub-structures. Therefore, in the case of high-rise buildings, irregular shaped buildings, buildings which are expected to be affected by large differential settlement and remodeling buildings, the unified structural model for super- and sub- structures was recommended for structural analysis instead of the separate structural model.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.5 no.4
• /
• pp.97-105
• /
• 2001

Rubber bearings may exhibit a significant cold temperature effect and some velocity dependency(strain rate effect). Both of these attributes which affect non-linear behavior must be accounted for when accurately modeling the bearings behavior, therefore, an analytical models is proposed to consider the effects of the cold temperature and strain rate on both rubber and lead. From the results of an experimental investigation where the frozen bearings were tested under lateral cyclic loading with constant axial load, a non-linear system identification with least squares procedure was applied to determine the material properties of rubber and lead. It is demonstrated that the proposed analytical model is able to simulate the reversed cyclic loading behavior of elastometric and lead-rubber bearings.

• Journal of the Society of Naval Architects of Korea
• /
• v.37 no.3
• /
• pp.110-121
• /
• 2000

Gas heating, high frequency induction heating and laser heating can be used as the heat-source of line heating. Most of shipyards have been using the gas heating method for line heating. It is difficult to control the residual deformation of gas heating. High frequency induction heating is more feasible for the automation of line heating rather than the gas heating method since it is easy to control the magnitude of heat input. In this study, a numerical model of high frequency induction heating process is proposed for the application of the line heating. The simulation process of the induction heating is composed of the electromagnetic analysis, the heat transfer analysis, and the thermal deformation analysis.

• Computational Structural Engineering
• /
• v.8 no.2
• /
• pp.115-121
• /
• 1995

The object of this study is to propose a rational method of resistance strength and flexural deformation for structures using high strength concrete(400-700kgf/cm/sup 2/). The material property(stress-strain relationship) is to be modelize using regression analysis of experimental result. And the applicability of trapezoidal stress model is to be verified. An analytical method is used by the moment-curvature relationship which is based on stress-strain relationships of material for discreted element of section. The evaluation method of moment-curvature of high strength concrete structures is also proposed by using the Monte Carlo Simulation based on a probabilistic concept that could minimize an error due to iterated calculations and random variable of material properties.

• Tunnel and Underground Space
• /
• v.21 no.3
• /
• pp.216-224
• /
• 2011

In this study, Class II behavior of rock failure process under uniaxial and biaxial compression has been numerically simulated using bonded particle model. Class II behavior of rock was simulated by radial strain controlled uniaxial and biaxial compression tests using a suggested method of ISRM. Micro-parameters used in the simulation were determined based on the laboratory uniaxial compression tests carried out at ${\"{A}}sp{\"{o}}$ Hard Rock Laboratory, Sweden. Class II behavior of ${\"{A}}sp{\"{o}}$ rock was effectively simulated using newly proposed numerical technique in this study, and the results of numerical simulations show good similarity with the complete stress-strain curves for Class II behavior obtained from the laboratory tests.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.13 no.1
• /
• pp.69-76
• /
• 1995

This study is the 3-D precision deformation measurement of a bridge, obtain results of precision control points by GPS and 3-D measurement system and develope efficientlty technices which can solve precision 3-D analysis by CRP In the result, we could overcome the problems of former control point measurement in the way of the combination system of GPS and 3-D measurement system to positioning decision of reference points and control points. Then we could symplify old measurement process on the 3-D deformation analysis of a linear structure and complement parted analysis fault of measurement instrument.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.8 no.6 s.40
• /
• pp.1-11
• /
• 2004

In the previous study(1), the finite element method was used for the vertical vibration analysis of suspension bridge considering the effects of the shear deformation and the rotary inertia under moving load. This study firstly performs the eigenvalue analysis for the free vertical vibration of suspension bridge using FEM analysis. Next the equations of motion considering interaction between suspension bridge and vehicles/train are derived using mode superposition method. And dynamic analysis was performed using the Newmark $\beta$ Method. Finally through the numerical examples, the dynamic responses of bridges by this study are investigated.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.5
• /
• pp.82-88
• /
• 2011

In the present work, FEM analyses are carried out to investigate the fractures occurred within the structural part in the course of combustion experiment. The loss of structural integrity stems from the localized deformation and the damage induced due to a severe change in the thermal load. Moreover, the two-back stress evolution model is proposed using the Armstrong-Frederick and the Phillips' rules to depict the plastic deformation, and the continuum damage mechanics is also incorporated into the present model. It is noted that the present model is able to formulate a wide range of constitutive description with ease. The numerical results depicts that a severe strain localization and damage evolution can be obtained depending on the dominant back stress.

• Journal of the Microelectronics and Packaging Society
• /
• v.10 no.4
• /
• pp.1-8
• /
• 2003

Thermo-mechanical behavior of a ceramic ball grid array (CBGA) package assembly are characterized by high sensitive moire interferometry. Moir fringe patterns are recorded and analyzed at various temperatures in a temperature cycle. Thermal-history dependent analyses of global and local deformations are presented, and bending deformation (warpage) of the package and shear strain in the rightmost solder ball are discussed. A significant non-linear global behavior is documented due to stress relaxation at high temperature. Analysis of the solder interconnections reveals that inelastic deformation accumulates on only eutectic solder fillet region at high temperatures.

• Journal of the Korean GEO-environmental Society
• /
• v.8 no.6
• /
• pp.61-68
• /
• 2007

The problem on cyclic plate load tests was analyzed by finite element method using an anisotropic hardening constitutive model. The constitutive model was coded to user subroutine in ABAQUS. Using the result of the analysis, Young's moduli corresponding to various strain levels were evaluated by a back calculation method and were very similar to those of input. On the basis of the back calculation method plate loading tests were verified. As a result, deformation moduli could be evaluated practically from cyclic plate load tests with respect site conditions.