• The Journal of the Acoustical Society of Korea
• /
• v.26 no.6
• /
• pp.293-300
• /
• 2007

Turbulent boundary layer over an underwater vehicle is formed when it moves underwater and wall pressure fluctuation within the turbulent boundary layer generates flow-induced noise by exciting the elastic hull of the underwater vehicle. One of the methods to reduce this flow noise is to attach a compliant layer on the surface of the vehicle. In order to observe the possibility of noise reduction in the water when the compliant layer treatments are applied on the surface, three types of specimens those are a bare steel plate, a steel plate coated with neoprene and a steel plate with polyurethane coating material are tested at various flow speeds in a low noise cavitation tunnel. This paper presents the results of measurements and analysis of wall pressure fluctuations which is a main source of flow noise, within the turbulent boundary layer on three specimens. Its results could be shown that about 10dB reduction of wall fluctuation pressure at high frequencies was achieved due to the dissipation of turbulent energy by the compliant coating while it makes the turbulent boundary layer thicker and changes the behavior of turbulent flow in the layer.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.3
• /
• pp.379-386
• /
• 1985

본 연구에서는 부차적으로 이와 같은 광반사법의 유용성을 개발, 평가하고자 한다. 또 실험에서 벽면에 부착되는 입자는 기하학적 형상에 따라 입자주위의 유체 흐름에 지배적인 영향을 받게 되므로 실험을 통하여 입자의 기하학적 형상에 따라 변 화되는 열확산 효과의 상대적인 영향을 평가한다.

• Applied Microscopy
• /
• v.41 no.2
• /
• pp.139-145
• /
• 2011

Parthenocissus tricuspidata is an epiphyte that lacks a main axial stem, but develops adhesive disks along the stem for climbing support. In this study, scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS) were utilized to examine the brick wall surface and the adhesive disks of P. tricuspidata that attached to the surface successfully. The study was mainly focused the outermost layers of both structures before and after adhesion to find out whether there has been some structural and/or physical interactions between the two. The adhesive disks adhered firmly to the brick wall by secreting adhesive materials that help them for a tight attachment to the surface. The rough wall surface appeared facilitating better attachment of the adhesive disks by infiltrating the materials into those spaces leading to some degree of interactions at the interface. EDS analysis on the outermost layers of the adhesive disks that were separated from the substrates was also consistent with the SEM data on the interaction between the adhesive disks and the substrate surface. EDS analysis of the brick wall surface and the adhesive disks demonstrated similar elements of O, Si, Fe, Al, K, Mg, and Na in their components.

• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.1
• /
• pp.52-66
• /
• 1998

An experimental study on the flow characteristics was performed for a two-dimensional turbulent wall attaching offset jet at different oblique angles to a surface. The flow characteristics were investigated by using a split film probe with the modified Stock's calibration method. The jet mean velocity, turbulent intensity, wall static pressure coefficient profiles, and time-averaged reattachment point were measured at the Reynolds number Re (based on the nozzle width, D) ranging from 17700 to 53200, the offset ratio H/D from 2.5 to 10, and the inclined angle .alpha. from 0.deg. C to 40.deg. C. The Correlations between the maximum pressure position, minimum pressure position, and reattachment point and offset ratios, and inclined angles are presented.

• Geotechnical Engineering
• /
• v.26 no.1
• /
• pp.24-36
• /
• 2010

• Proceedings of the KAIS Fall Conference
• /
• 2009.12a
• /
• pp.1026-1029
• /
• 2009

현재 남해안 굴양식산업은 어업인들의 중요한 소득원이 되고 있으나, 굴양식장에서 발생되는 굴패각은 처리곤란 및 악취발생으로 인해 또 다른 해양오염원으로 그 문제성이 심각하게 대두되고 있는 실정이다. 굴양식장에서 연간 약 28~30만여톤의 굴패각이 발생되고 있으며, 그 중 10~20%는 종패부착용이나 비료로 재활용되고 있고, 80~90%는 매립되거나 야적 방치된다고 보고되고 있다. 본 연구에서는 굴패각을 재활용하고자 굴껍질의 성분분석을 실시하여 나노고분자세라믹 코팅제의 세라믹 소재로써의 적용 가능성여부를 확인하였고, 경기도 P정수장 내 여과지 콘크리트 벽면에 코팅처리하여 그 성능을 확인하였다. 그 결과 패각의 굴껍질은 90%이상이 탄산칼슘($CaCO_3$)로 이루어져 있었으며, 굴껍질을 재활용한 나노고분자세라믹 코팅제는 pH 7.5~8.5로서 일반수도를 측정한 pH 7.3~7.8과 유사한 결과를 보였다. 또한, 나노고분자세라믹 코팅제의 콘크리트 벽면에 대한 부착강도는 한국산업규격에 제시된 폴리머의 방수재료 부착강도인 8~10(kg.f/$cm^2$)이상의 값이 나타남에 따라 패각의 굴껍질을 재활용한 나노고분자세라믹 코팅제의 경기도 P정수장 내 여과지 콘크리트 벽면 코팅제로써 적용이 가능한 것으로 확인 되었다.

• Journal of Energy Engineering
• /
• v.2 no.3
• /
• pp.251-257
• /
• 1993

The purpose of this study is to obtain an improved interpretation of heat transfer phenomena between blocks and fluids in the parallel conducting plates. Flow is two-dimensional, incompressible steady laminar flow over rectangular blocks, representing finite heat source on parallel plate. Heat transfer phenomena, temperature of blocks and heat transfer into the flow field are investigated for different spacings between blocks and Reynolds numbers. Results indicate that Nusselt number on the far upstream corner of the block was higher than that of any part of the block. As Reynolds number and spacings of blocks increased, Nusselt number increased. The distribution of local Nusselt number on the top surface of the conducting plate is similar to the case with insulated plate. Temperature of the block which has heat source in half cubage was approximately twice as high as temperature of the block which has heat source in whole cubage. As Reynolds number and spacings of blocks increased, overall temperature decreased. The peak value of block temperature occurred at position shifted to the right or upper right from center. The maximum temperature of block can be expressed as a function of Reynolds number, spacings between blocks, position of maximum temperature of each block and then it is possible to predict the maximum temperature of blocks.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.5
• /
• pp.828-836
• /
• 1987

The inclusion of thermophoresis in particle deposition studies has often been treated separately from deposition due to flow characteristics. Also previously reported experimental results on thermophoresis have been studied in the regions of relatively small temperature gradients. In this study, using real-time laser light reflectivity method, we measured the angular dependence of the deposition rates of particles of the cylindrical collector surface, which immerged in laminar flow of a hot gas suspension of small particles. And we extended the previous narrowband results of thermophoretic deposition rates to the regions of large temperature gradients between the hot gas stream and the collector surface. Based on the obtained data, the cylinder's forward stagnation-point region is considerably enriched in particle 'phase' density owing to the compressibility effect, which leads to locally enhanced deposition while the downstream region from the stagnation point inertial force acts in the opposite direction, which tends to centrifuge particles away from the wall, thus the local deposition rates by thermophoresis are reduced.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.05a
• /
• pp.919-920
• /
• 2014

따개비(barnacle)는 선저부에 붙어서 번식하며 딱딱한 석회질 껍데기로 덮여있다. 이로 인하여 선박의 속도를 저하시키고 도료기능을 상실시키는 주요인이 된다. 이를 제거하기 위해 작업자가 직접 액체를 분사하고 브러쉬로 세척해야 한다는 불편함과 위험에 노출되기 때문에 선박작업용 로봇이나 기계들이 많이 개발되고 있다. 현재 연구 중이거나 개발이 완료된 것 중에는 영구자석 또는 전자석 휠을 사용하거나 공압을 이용하여 수직벽면에서 작업을 한다. 특히 공압 방식을 많이 사용하였는데 수직벽면에 로봇이 밀착될 만큼 강한 공압이 필요하게 되기 때문에 부가적인 장치가 많이 필요하다. 본 논문에서는 부가적인 장치를 최소화하고 효과적인 동작을 하기위해 전자석 방식을 선택 하였으며 간편하게 선박의 수직벽면을 작업할 수 있는 전자석 방식의 4륜 로봇을 개발하고자 한다. 선박의 수직벽면 작업용 4륜구동 로봇을 전자석을 이용하여 수직벽면에 부착할 수 있도록 설계하였으며 자력의 세기와 방향을 제어하여 로봇이 선박의 수직면에 밀착되어 자유롭게 이동이 가능하도록 개발 하고자 한다.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.5 s.122
• /
• pp.405-414
• /
• 2007

In recent years, experimental and theoretical studies show that turbulent flows looking disordered have a definite structure produced repetitively with visible order. As a core structure of turbulence, hairpin vertices are believed to play a major role in developing and sustaining the turbulence process in the near wall region of turbulent boundary layers and may be regarded as the simplest conceptual model that can account for the essential features of the wall pressure fluctuations. In this work, fully developed typical hairpin vortices are focused and the associated surface pressure distributions and their corresponding spectra are estimated. On the basis of the attached eddy model, the overall surface pressure spectra are represented in terms of the eddy size distribution. The model is validated by comparison of predicted wavenumber spectra with existing empirical models, the results of direct numerical simulation (DNS) and also spatial correlations with experimental measurements.