• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.6
• /
• pp.1282-1291
• /
• 1989

본 연구에서는 이러한 연구의 시작단계로 노즐내의 열 경계층 방정식을 정리하고 압축성 와점도모델을 도입하여 유한 차분법을 이용한 전산프로그램을 작성 하였다. 한편 실제로 추진모테에서는 고온 고속의 열기류가 분출되기 때문에 추진 하고 있는 동안 노즐벽을 형성하고 있는 내열재가 심하게 손상되어 표면의 상태가 매우 거칠게 된다. 더구나 경우에 따라서는 내열재가 용발(ablation)하게 된다. 이러한 상태를 감안하여 마찰계수와 열전달 계수를 합리적으로 추정해야만 노즐의 설계와 주변장치를 합리적으로 수행할 수 있다. 따라서 본 연구에는 주로 경계층 내의 압력구배, 압축성의 효과, 물성치의 변화를 고려한 기존 난류모델에 근거하여 프로그램을 작성하고, 이것을 토대로 노즐표면 조도의 영향 및 분출(blowing)의 영 향을 중점적으로 고려하여 그 특성을 연구하였다. 노즐벽에서 분출을 고려한 이유는 표면이 용발할 때 표면의 온도가 거의 일정하게 유지된 상태로 노즐표면이 화학작용을 수반하면서 가스화됨을 초보적으로 고려해보기 위함이다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.1
• /
• pp.140-152
• /
• 1997

A simultaneous measurement of the wall skin friction and near-wall streamwise velocity fluctuations is performed using hot film and hot wire anemometers to investigate the relation between them. Near-wall turbulence statistics measured with a hot-wire probe are in good agreement with previous results. Turbulence properties of the wall skin friction fluctuations measured with a hot film also show fairly good agreements with those measured by others except that rms level is lower in the present study. Long-time averaged space- time correlations show that the wall skin friction is highly correlated with a turbulence structure which is tilted from the wall in the streamwise direction. Tilting angles are obtained from the phase shifts between the wall skin-friction and streamwise velocity fluctuations. The convection velocity of the near-wall streamwise velocity obtained from the space-time correlation is in good agreement with that from the direct numerical simulation database.

• Geotechnical Engineering
• /
• v.12 no.4
• /
• pp.87-100
• /
• 1996

The pull -out test has been used to investigate the friction properties between soil and grid type geosynthetics which is useful to measure the passive bearing resistance as well as the skin friction. In this paper, the friction properties between geogrid and a weathered granite soil are investigated by performing various pull-out tests. From the test results, a rational pull out test equipment and test method is suggested by evaluating the effects of major factors (such as geogrid width, location of soil box facing, vertical loads and pulll -out displacement rate, etc.) on pull -out test results.

• Journal of Korean Society of Steel Construction
• /
• v.26 no.4
• /
• pp.349-359
• /
• 2014

Until now, wall-slab plate of steel plate concrete has been constructed by joint. But, the shear plate has problems in the workability as well as structural integrity. This study investigates the behavior and strength of rib stiffened SC wall-slab connection. Seven prototype specimens of wall-slab connections were fabricated and tested. the structural safety of the specimens was confirmed through the monotonic loading test. Based on the experimental observations, this study propose the strength formula of the joint was proposed. To enhance the reliability of the proposed strength formula, analytical verification was performed through inelastic finite element analysis. Effect of parameters, such as, load point, friction coefficient, on the joint strength was examined. The proposed formula yields a conservative value for most cases.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.8
• /
• pp.905-910
• /
• 2013

The flow analysis has been made by applying the turbulent models in the helically coiled tubes of heat transfer. The k-${\varepsilon}$ and Spalart-Allmaras turbulent models are used in which the structured grid is applied for the simulation. The velocity vector, the pressure contour, the change of residuals along the iteration number and the friction factors are simulated by solving the Navier-Stokes equations to make clear the Reynolds number effect. The helical tube increases the centrifugal forces by which the wall shear stress become larger on the outer side of the tube. The centrifugal force makes the heat transfer rate locally larger due to the increase of the flow energy, which finds out the close relationship between the pressure drop and friction factor in the internal flow. The present numerical results are compared with others, for example, in the value of friction factor for validation.

• The Journal of the Korea Contents Association
• /
• v.15 no.2
• /
• pp.499-506
• /
• 2015

The friction velocity is a quantity with the dimensions of velocity defined by the friction stress and density of a wall surface at near wall of flow condition. Also, the friction velocity is the hydraulic parameter describing shear force at the bottom flow. Moreover, it is a very important factor in designing open channel and essential to determine the mixing coefficient in the main flow direction. The estimation of the friction velocity are such as methods using channel slope, linear law of the mean velocity at viscous sub-layer and direct measurement of wall shear stress, etc. In the present study, we propose a friction velocity equation that has been optimized by combining the concept of entropy, which is used in stochastic method, and to verify the proposed equation, the experimental data measured by Song was used. The R squared for friction velocities between proposed equation and friction velocity formula analyzed 0.999 to 1.000 in a very good agreement with each equation.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1046-1047
• /
• 2015

기존에 시행 중인 도로교통 소음을 저감시키기 위한 방안인 방음벽과 저소음 포장은 보편적으로 사용되어 오고 있으나, 몇 가지 단점을 가지고 있다. 방음벽은 높은 시공으로 인한 도시 경관 저하, 과도한 시공비 및 유지비, 조류가 방음벽에 부딪혀 유발되는 생태계 교란 현상 등 여러 문제점을 가지고 있다. 또한, 저소음 배수성 포장은 타이어와 도로 포장간의 마찰 소음을 원천적으로 저감시키는 효율적인 공법이나, 시공 후 일정기간이 지나면 공극이 막혀 성능이 저하되어 유지 보수가 적절하게 필요한 단점이 있다. 수음점의 거리별 소음예측을 통하여 일반적인 원소음과 능동형 소음 저감 기술(ANC) 적용 후의 효과를 알아보고, 소음원의 제어 및 영향거리에 따른 저감 목표를 예측하고자 한다.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.2
• /
• pp.246-252
• /
• 2018

In this paper, the friction drag force of 3D submerged body is investigated by considering the surface roughness, the first grid height, and the Reynolds number using open CFD source code, OpenFOAM 4.0. A procedure for estimating drag components by CFD code is set up and suggested in this study. In the 3D submerged body, because of the form factor in the 3D computations, the friction resistance with the small roughness of $12{\mu}m$ obtains different result with the smooth wall. As the Reynolds number increased, the boundary layer becomes thinner and the fiction resistance tends to decrease. In the computations for the effect of y+, the friction resistance and wall shear stress are excessively predicted when the y+ value deviates from the log layer. This is presumably because the boundary layer becomes thicker and the turbulence energy is excessively predicted in the nose due to the increase in y+ value. As the roughness increases, the boundary layer becomes thicker and the turbulence kinetic energy on the surface increases. From this study, the drag estimation method, considering the roughness by numerical analysis for ships or offshore structures, can be provided by using the suggested the y+ value and surface roughness with wall function.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.5
• /
• pp.147-155
• /
• 2001

좁은 되메움 공간의 벽체가 연직 또는 한쪽 벽체만이 경사진 경우 수평토압에 관한 연구는 국내외에서 상당히 진전되어 왔으나, 대칭으로 경사진 경우의 연구는 미흡한 실정이다. 본 연구는 되메움 공간의 벽체가 대칭으로 경사지고 벽체간 하부폭이 다를 때 발생되는 수평토압에 관한 거동을 구명하기 위하여 시도되었다. 이를 위하여 모형토조를 사용하여 되메움 공간의 벽체가 대칭으로 경사진 경우 벽체의 경사각, 하부폭, 벽마찰각, 상대밀도를 변화시켜 총 24종류의 모형실험을 수행하였고, 이 결과를 Kellogg(1993)제안식, 벽면경사를 고려한 수정 제안식 및 벽면마찰반력으로부터 구한 수평토압과 비교, 분석하였다. 연구 결과 벽면마찰반력을 고려한 경우 평균연직토압을 적용하였음에도 Arching 효과가 발휘된 실험결과와 가장 근소한 차이를 나타내었다.

• Journal of Korean Society of Steel Construction
• /
• v.20 no.2
• /
• pp.347-354
• /
• 2008

Steel plate-concrete (SC) structure has recently been used in nuclear power structure because of its construction efficiency. In this study, experimental and analytical study to investigate the behavior of the SC structure's wall slab connection was carried out. Experiments were performed for typical SC and RC connections in order to examine the basic difference between each structure. Finite element analysis was performed and the result of the analysis was found to closely reflect the experimental result. By varying the thickness of the shear plate and friction coefficients and the distance of applied load from the wall, the influence of the parameters on the joint strength and failure modes were examined. Finally, it was confirmed that the joint strength formula proposed in th this research gives conservative results.