• Journal of Biomedical Engineering Research
• /
• v.45 no.1
• /
• pp.10-19
• /
• 2024

The purpose of this study is to conduct a summative evaluation of the usability of a general-purpose ventilator to determine whether it can be used for its intended purpose in the intended environment by the intended user and to find possible errors in use. The importance of ventilators has increased due to the accelerated aging of the population and the impact of the pandemic. In addition, patients who require ventilators are often in critical condition, so even a small error in use can be fatal. Therefore, it is important to ensure that the ventilator has sufficient stability and can be used satisfactorily without inconvenience to the user. In this study, we conducted a usability test with 17 respiratory nurses with more than 3 years of experience using the ventilator. We analyzed the task success rate, satisfaction, and opinions of the intended users while going through a total of 17 scenarios. Satisfaction was captured through an ASQ questionnaire and subjective opinions were captured through a detailed opinion questionnaire. The results showed a high level of satisfaction with an average score of 6.3 for the use scenarios. Evaluators expressed satisfaction with the overall visibility and versatility of the features, but noted that improvements were needed for calibration tasks with low task success rates. As the calibration method is different from other equipment, it was suggested that specific explanations of the calibration method and the picture that appears when calibrating are needed, and that if relevant training is provided, the equipment can be used without problems. If the usability evaluation is not limited to securing efficiency and satisfaction from the intended users, but also continuously receives feedback from users to prepare for use in emergency environments such as pandemic situations, it will be very helpful to seize opportunities such as emergency authorization in future situations, and ultimately contribute to patient safety by reducing use errors.

• Progress in Medical Physics
• /
• v.22 no.4
• /
• pp.190-197
• /
• 2011

Currently, the dose distribution calculation used by commercial treatment planning systems (TPSs) for high-dose rate (HDR) brachytherapy is derived from point and line source approximation method recommended by AAPM Task Group 43 (TG-43). However, the study of Monte Carlo (MC) simulation is required in order to assess the accuracy of dose calculation around three-dimensional Ir-192 source. In this study, geometry factor was calculated using segmented sources integration method by dividing microSelectron HDR Ir-192 source into smaller parts. The Monte Carlo code (MCNPX 2.5.0) was used to calculate the dose rate $\dot{D}(r,\theta)$ at a point ($r,\theta$) away from a HDR Ir-192 source in spherical water phantom with 30 cm diameter. Finally, anisotropy function and radial dose function were calculated from obtained results. The obtained geometry factor was compared with that calculated from line source approximation. Similarly, obtained anisotropy function and radial dose function were compared with those derived from MCPT results by Williamson. The geometry factor calculated from segmented sources integration method and line source approximation was within 0.2% for $r{\geq}0.5$ cm and 1.33% for r=0.1 cm, respectively. The relative-root mean square error (R-RMSE) of anisotropy function obtained by this study and Williamson was 2.33% for r=0.25 cm and within 1% for r>0.5 cm, respectively. The R-RMSE of radial dose function was 0.46% at radial distance from 0.1 to 14.0 cm. The geometry factor acquired from segmented sources integration method and line source approximation was in good agreement for $r{\geq}0.1$ cm. However, application of segmented sources integration method seems to be valid, since this method using three-dimensional Ir-192 source provides more realistic geometry factor. The anisotropy function and radial dose function estimated from MCNPX in this study and MCPT by Williamson are in good agreement within uncertainty of Monte Carlo codes except at radial distance of r=0.25 cm. It is expected that Monte Carlo code used in this study could be applied to other sources utilized for brachytherapy.

• Journal of Korean Society of Forest Science
• /
• v.90 no.4
• /
• pp.565-572
• /
• 2001

The spatial genetic structure of Needle fir(Abies holophylla Max.) seedlings on forest gap within a Needle fir forest at Mt. Odae in Korea was analyzed on the basis of ISSR(inter-simple sequence repeats) marker analysis. The gap size was $1,500m^2(50m{\times}30m)$, and we sampled 416 one- or two-year-old seedlings by 2m intervals. Some trees at the upper crown layer except Needle firs and all trees at the middle and lower crown layers were removed, and Needle firs at the upper crown layer showed very weak growth strength or to be withering to death. The results of spatial autocorrelation using 31 polymorphic ISSR markers revealed that it was genetically homogeneous within spatial distance of 15.6m and the randomness of genetic distribution was from 15.6m to 31.2m. The genetic patch size of seedlings in forest gap might be restricted by the density of mother trees, making allow for the average height of adult Needle firs, the seed dispersal area, and the average distance between adults. For the directionality of seedling distribution, we investigated the variography using 'genetic configuration' which was the value of configuration in Multidimensional Scaling by genetic distance. In directional variogram, the increment of spatial distance from East to West direction was inversely proportional to genetic homogeneity. We presumed that this anisotrophy of seedling distribution at this forest gap resulted from the directionality of seed dispersal rather than the difference of fecundity between mother trees or the microhabitat variation, taking the evenness of forest floor condition, a vast seed production and the random distribution of seedlings at the studied site into consideration.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.4
• /
• pp.815-826
• /
• 1994

Skew bridges are found frequently in new bridge construction due to geographical conditions when new constructing bridges are put across the existing highways, railroads or rivers. This study is to investigate the static behaviors of the steel deck plates of skew bridges which are increasingly used in bridges due to outstanding quality of structural steels, development of welding techniques, in order to reduce dead loads and period of constructions. The static behaviours of steel deck plates are analyzed using general purpose FE code SAP90 by modeling the skewed deck plates with rigorous finite elements, as the skew angles vary. The results of finite element analysis for the behaviors of steel deck plates and concrete slabs in acute, obtuse corners and center of decks are compared and discussed as the skew angles vary from $90^{\circ}$ to $30^{\circ}$. Two types of decks are treated, as isotropic plates and orthotropic plates, respectively. From the results of finite element analysis, it is found that more moments, reactions, and deflections occur at the obtuse corners than at the center of skewed decks regardless of isotropy or orthotropy. Especially, in case of the skewed deck plates with skew angles less than 45 degrees, significantly large discrepancies for the values of those internal forces are shown between the skewed and right deck plates. This study estimates the characteristics of deck behaviors according to skew angles, and proposes limitations of skew angles and the ciritical regions of decks.

• Journal of Korea Water Resources Association
• /
• v.48 no.7
• /
• pp.553-566
• /
• 2015

Acoustic Doppler Current Profilers(ADCPs) have capability to concurrently capitalize three-dimensional velocity vector and bathymetry with highly efficient and rapid manner, and thereby enabling ADCPs to document the hydrodynamic and morphologic data in very high spatial and temporal resolution better than other contemporary instruments. However, ADCPs are also limited in terms of the inevitable unmeasured regions near bottom, surface, and edges of a given cross-section. The velocity in those unmeasured regions are usually extrapolated or assumed for calculating flow discharge, which definitely affects the accuracy in the discharge assessment. This study aimed at scrutinizing a conventional extrapolation method(i.e., the 1/6 power law) for estimating the unmeasured regions to figure out the accuracy in ADCP discharge measurements. For the comparative analysis, we collected spatially dense velocity data using ADV as well as stationary ADCP in a real-scale straight river channel, and applied the 1/6 power law for testing its applicability in conjunction with the logarithmic law which is another representative velocity law. As results, the logarithmic law fitted better with actual velocity measurement than the 1/6 power law. In particular, the 1/6 power law showed a tendency to underestimate the velocity in the near surface region and overestimate in the near bottom region. This finding indicated that the 1/6 power law could be unsatisfactory to follow actual flow regime, thus that resulted discharge estimates in both unmeasured top and bottom region can give rise to discharge bias. Therefore, the logarithmic law should be considered as an alternative especially for the stationary ADCP discharge measurement. In addition, it was found that ADCP should be operated in at least more than 0.6 m of water depth in the left and right edges for better estimate edge discharges. In the future, similar comparative analysis might be required for the moving boat ADCP discharge measurement method, which has been more widely used in the field.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.20 no.1
• /
• pp.26-36
• /
• 2017

Korea is preparing an offshore carbon capture, transport and storage (CCS) demonstration project which is recognized as one of important $CO_2$ reduction technologies to mitigate climate change. The offshore CCS project aims to transport, inject and store large amount of $CO_2$ into offshore geologic formation, and has a potential risk of leakage which might cause disastrous damage to human health, environment and property. Therefore, in order to ensure the safety of the offshore CCS project, a strict HSE (health, safety and environment) management plan and its implementation are required throughout the project life cycle. However, there are no HSE domestic laws or regulations applicable to CCS projects, and the related research is insufficient in Korea. For the derivation of the essential and urgent requirement in HSE management framework applicable to the offshore CCS project in Korea, we analysed the HSE management methodologies and foreign CCS HSE management guidelines and cases. First, this paper has analyzed ISO 31000, a generalized risk management principles. Second, we have investigated the HSE management practices of CCS projects in Norway and UK. Based on the analyses, we suggested the necessity of developing the HSE Philosophy and the HSE management process through the whole life cycle. Application of HSE management in early phase of an offshore CCS project will promote systematic and successful project implementation in a cost-effective and safe way.

• Journal of Venture Innovation
• /
• v.2 no.2
• /
• pp.31-46
• /
• 2019

Materials and Parts acts as the bridge in the manufacturing industry. In 2018, the materials and parts industry became the leading industry in Korea as its export reached $316.2 billion, accounting for 52.3 percent of the country's total exports. As such, it is the main industry of Korea leading the trade surplus, but when it comes to Japan, it is not. The trade deficit with Japan shrinks to $24 billion last year but the materials and parts industry still accounts for 60 percent of total deficit, which is about $15.1 billion. Today Japan has the top competitiveness in the high-tech materials and parts industry and the factors can be found in cooperation and symbiosis among companies, monotsukuri spirit, and long-term government policy. In order for Korean economy to pursue the Japan's high-tech materials and parts industry, the following change of perception is necessary. First, the material and parts industry requires win-win cooperation. In general, materials and parts are intermediate products. Therefore, it is important to understand the characterist that the transactions are all made up between companies not the with consumers. Second, expansion of joint technology development is absolutely necessary. South Korea is a leading country in the field of general-purpose materials and parts. However, the research shows that South Korea has structure which small and medium-sized companies could have difficulties in developing high-tech products as finding demand and developing market are hard due to low participation of large corporations at R&D stage. It is necessary for large corporations to participate in joint R&D and share opinions of customers from the beginning stage of R&D. Third, a long-term approach is needed. Structural vulnerabilities in the Korea's materials and parts industry, including the lack of advanced technologies is the main reason of solidification of Korea's trade deficit with Japan but there are also cultural differences about technology in the background. Even if it takes time, a long-term approach is absolutely necessary to build up technology and know-how in order to secure competitiveness in the high-tech materials and parts industry. This approach applies to act of corporation and government policy.

• Economic and Environmental Geology
• /
• v.38 no.6 s.175
• /
• pp.607-622
• /
• 2005

This study was carried out in order to evaluate where the soil loss was mainly occurred, .and to verify how riverbed sediments in the tributaries of the Seomjin River were related to their source rocks distributed in Sunchang area. The study area including the Seomjin River with 4 tributaries of Kyeongcheon, Okgwacheon, Changjeong-cheon and Ipcheon was divided into 10 watershed. The RUSLE (Revised Universal Soil Loss Equation) was estimated for all the grids (10 m cells) in the corresponding watershed. The amount of soil loss per unit area was calculated as follows: dry fold (53,140.94 tons/ha/year), orchard (25,063.38 tons/ha/year), paddy field (6,506.7 tons/ha/year) and Idlest (6,074.36 tons/ha/year). The differences of soil loss per unit area appear to be depends on areas described earlier. Soil erosion hazard zones were generally distributed within dry fields. Several thematic maps such as land use maps, topographical maps and soil maps were used as a data to generate the RUSLE factors. The amount of soil loss, computed by using the RUSLE, showed that soil loss mainly occurred at the regions where possible source rocks were distributed along the stream. Based on the this study on soil loss and soil erosion hazard zone together with chondrite-normalized REE patterns that were previously analyzed in same study area, a closed relationship between riverbed sediments and possible source rocks is formed. Especially in the Okgwacheon that are widely distributed by various rocks, chondrite-normalized REE pattern derived from the riverbed sediments, source rock and soil is expected to have a closed relationship with the distribution of soil loss.

• Korean journal of applied entomology
• /
• v.46 no.1 s.145
• /
• pp.109-115
• /
• 2007

This study was carried out to determine occurrence and damage of golden apple snail, Pomacea canaliculata on water seeding area in Jeonnam province. The density of golden apple snail maintained hlgh until October 2003, but quickly decreased from November. They overwintered only in a portion of the water canals but could not find in dried paddy field. They reproduced from May and June in the canal water and paddy field, respectively. Feeding time of golden apple snail on rice seedlings was 235.2 seconds, feeding length of that was 8.4cm. When golden apple snail fed rice seedlings, the stem remain only 2.5cm from areal part which could not recover. The more density of golden apple snail, the fester feeding rate. Density and number of eggs laid of golden apple snail after overwintering was higher on bank around of paddy field than on middle of that. The percent of shell size after over wintering was higher in small (below 25mm) than big (over 36mm). But in case of Boseong area, the slze was reverse because the soil has soft mud. The survival rate of overwintering golden apple snail was lower than that of breeding. They did not move when the temperature changed rapidly, but the temperature increased they start to move. They dead almost below $-3^{\circ}C$. The damage of rice by golden apple snail in the direct water seeding was 20%. In machine transplanting, rice damaged only fore-end of leaf and recovered subsequently. When golden apple snail release in direct water seeding field, the percent of damage was 5.6% in immediately release plot. The later release, the lower damage.

• The Korean Journal of Nuclear Medicine
• /
• v.34 no.1
• /
• pp.55-61
• /
• 2000

Purpose: We performed this study to evaluate the changes of gallbladder ejection fraction (GBEF) in diabetic patients with or without autonomic neuropathy. Materials and Methods: This study included 37 diabetic patients (25 women, 12 men, mean age 51 years) and 24 normal controls (10 women, 14 men, mean age 38 years). After intravenous injection of 185 MBq of $^{99m}Tc$-DISIDA, serial anterior abdominal images were acquired before and after fatty meal. Regions of interest were applied on gallbladder and right hepatic lobe on 60 and 90 minute images to calculate GBEF. Results: GBEF was significantly reduced in diabetes with autonomic neuropathy ($43{\pm}12.3%$) and without autonomic neuropathy ($57.5{\pm}13.2%$) compared with normal controls ($68{\pm}11.6%$, p<0.05). And also, GBEF was significantly reduced in diabetes with autonomic neuropathy compared with diabetes without autonomic neuropathy (p<0.05). Fasting blood glucose level, age, sex, hemoglobin Alc, body mass index, serum lipid level were not different in these two diabetic patient groups (p>0.05). When 50.2% of GBEF was used as the criteria for diabetic autonomic neuropathy, the sensitivity and specificity were 80%, 76.5%, respectively. The area under receiver operating characteristic curve was 0.846. Conclusion: GBEF of diabetic patients with autonomic neuropathy was significantly reduced than that of diabetic patients without autonomic neuropathy.