• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.6
• /
• pp.119-127
• /
• 2002

The paper presents the effect of the backlash magnitude and the supplied voltage of motor on the gear reduction servo system. The bandwidth of the system depends heavily on the supplied voltage of motor as well as the backlash magnitude. Specially, the bandwidth of the system increases as the supplied voltage of motor increases. 1t is shown that the system has the bandwidth of zero backlash in case of motor supplied voltage is infinite. It is also found that the magnitude of the supplied voltage of motor is very important in case of the analysis of the system bandwidth.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.5
• /
• pp.103-109
• /
• 2002

The paper investigates the change of frequency response characteristics on two-stage gear reduction servo system according to the variation of backlash amount of each gear reduction stage, under the condition that the backlash of total system is constant. It is shown that the frequency response characteristics of the system heavily depend on the contribution ratio which is defined as a ratio of the first backlash amount to the total backlash. It is also found that there is an optimal backlash combination to maximize the bandwidth of two-stage gear reduction servo system when the allowable total backlash is determined.

• The Bulletin of The Korean Astronomical Society
• /
• v.41 no.1
• /
• pp.74.1-74.1
• /
• 2016

미국 텍사스 주 맥도날드 천문대에 위치한 2.1m 망원경에 부착된 SQUEAN (SED Camera for QUasars in EArly uNiverse)은 2010년부터 운용되고 있는 CQUEAN을 바탕으로 개발된 적외선 영역 광학기기이다. 20개의 필터 장착이 가능한 필터 휠 제어 시스템을 가지고 있는 SQUEAN 시스템은 SMOP (SQUEAN Main Observation software package), KFC82 (KHU Filter wheel Control software package for McDonald 82 inch Telescope), KAP82 (KHU Auto-guiding software Package for McDonald 82 inch Telescope) 등으로 구성되어 있다. 그러나 대형 필터 휠을 제어하는 모터의 토크부족과 감속기의 백래시(Backlash)의 영향으로 오프셋의 오차가 커서 초기위치의 재설정 없이 하룻밤 이상 관측을 지속하는데 어려움이 있었다. 토크가 크고 인코더가 장착된 모터 교체와 제어 프로그램 등을 변경하고, 백래시의 영향을 최소화할 수 있도록 소프트웨어로 보정하였다. 또한, SMOP로부터 네트워크 통신을 통해 초기화용 필터 마스크(Initial Filter Mask:IFM)를 제작하여 돔 플랫 이미지에서 정확한 필터의 위치를 측정하는 기능을 도입하였다. 이 발표에서는, 개선된 하드웨어 및 소프트웨어의 내용과 테스트한 결과에 대해 보여준다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.10
• /
• pp.2130-2141
• /
• 2002

A unique technique to estimate the magnitude or contribution ratio of each stage backlash in a system with a two-stage gear reducer is proposed. The concept to estimate the magnitude or contribution ratio of each stage backlash is based on the change of frequency response characteristic, in particular, the change of anti-resonant frequency and resonant frequency, due to the change of each stage backlash magnitude, even though the total backlash magnitude of a system with a two-stage gear reducer is constant. The validity of the technique is verified in a seeker gimbal and satisfactory results are obtained. It is thought that the diagnosis and maintenance of the manufacturing machines and systems with two-stage gear reducers will become more efficient and economical by virtue of the proposed technique.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.7
• /
• pp.677-684
• /
• 2010

Backlashes of gears provide gears for good lubrication and for removal of the interference between teeth by the wear and manufacturing errors. The backlash is the strong nonlinear factor to gears. This study deals with nonlinear modeling of helical gears with backlash. Excitation of helical gears comes from torque variation, the tooth surface error, and the periodical change of mesh stiffness. To study the effect of torque fluctuation, equation of motion for the single degree of freedom torsional model of helical gears with the periodical change of mesh stiffness and the backlash was derived. The Newmark beta method and the Newton-Raphson method were used to obtain the nonlinear behaviors of mesh forces of helical gears. All excitation frequencies initially caused the tooth separation and single-sided impacts of the gear pair and eventually led to the normal tooth contact. However, some special excitation frequencies caused the single-sided impacts in the entire time as well as the initial time. Damping increase reduced the duration of single-sided impacts, and the backlash increase caused those in the entire time domain.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.10a
• /
• pp.63-64
• /
• 2006

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.12
• /
• pp.3246-3252
• /
• 1994

The vibration of meshing gear system is originated form teeth deformation, teeth contact ratio, profile error, etc. The gear vibration is classified as whine vibration during meshing and as rattle vibration during idling. In this study, the whine vibration is investigated under the assumption of piecewise linearity of elastic stiffness due to the variation of meshing. Numerical, theoretical and experimental investigations show the existence of the superharmonic components of the second and the third order. consistently It can be concluded that the superharmonic components in whine vibration of meshing gear is originated from the stiffness variation. It also shows that the higher order harmonics are reduced on the increase of motor speed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.11
• /
• pp.2713-2722
• /
• 2000

When designing a gear drive, designers should specify tolerances reasonably considering accuracy, cost, and manufacturing capability. In field design, however, designers mostly assign adequate tolerance without correlations between parts and assembly, resulting in iterative design dependent on experts know-how. In order to resolve this, the tolerance design system for a cylindrical gear drive is developed both to support tolerance design automation and to synthesize design processes of part and assembly tolerances. In this research, part tolerances are designed with the databases constructed by ISO, Ks, JIS and bearing catalogue, Assemble tolerance, that is, backlash tolerance is designed by synthesizing part design tolerances stochastically using the formulated assembly relations. This system can include part tolerance and fitting accuracy of shaft adn bearing in practical design. In addition, this system provides field-designers with a synthetic guideline for tolerance design of a gear drive.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.1
• /
• pp.62-69
• /
• 1993

The accuracy of machine tools is the major factor concerned with the acuracy of the processed work. The feed errors of feed system in machine tool, therfore, make the machining errors of work directly on processing. In this point, this study focused on the generative elements of feed errors in CNC cylindrical grinding machine, such as supporting method of ball screw, the effect of pitch and yaw error and the position detecting method in servo system when operating its shaft of grinding wheel head. Furthermore, in order to improve the driving accuracy of this machine tool, feed errors are measured by a laser interferometer. Results obtained in this study provide some useful informations to attain high accuracy of CNC machine tool.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.1
• /
• pp.17-24
• /
• 2011

TMED(Transmission Mounted Electric Device) parallel hybrid configuration can realize EV(Electric Vehicle) mode by disengaging the clutch between an engine and a transmission-mounted motor to improve efficiencies of low load driving and regenerative braking. In the EV mode, however, jerk can be induced since there are insufficient damping elements in the drive-train. Though the jerk gives demoralizing influence upon driving comport, adding a physical damper is not applicable due to constraints of the layout. This study suggests the jerk reduction control, composed of active damping method and torque profiling method, to suppress the jerk without hardware modification. The former method creates a virtual damper by generating absorbing torque in the opposite direction of the oscillation. The latter method reduces impulse on the mated gear teeth of the drive-train by limiting the gradient of traction torque when the direction of the torque is reversed. To validate the effectiveness of the suggested strategy, a series of vehicle tests are carried out and it is observed that the amplitude of the oscillation can be reduced by up to 83%.