• Proceedings of the Korean Geotechical Society Conference
• /
• 1994.03b
• /
• pp.47-62
• /
• 1994

Polyol을 주성분으로 하는 A액과 MDI계 isocyanate로 구성된 B약을 배합비와 배합속도를 각각 1:2에서 1:4까지, 300rpm에서 900rpm까지 변화시키면서 혼합하였다. 생성된 foamed polyurethane은 600rpm의 배합속도에서 배합비가 1:2에서 1:4로 감소함에 따라 발포율이 증가하는 현상을 보였다. 300rpm의 배합속도에서는 거의 발포가 되지 않았음, 900rpm의 배합속도에서는 발포는 되었으나 brittle한 물성을 보였다. 열변형온도 및 하중에 대한 변형율은 600rpm에서 1:2에서 1:3의 배율시 가장 우수한 것으로 관찰되었다.

• Journal of Energy Engineering
• /
• v.9 no.4
• /
• pp.279-287
• /
• 2000

코크스 오븐에서 석탄 건류과정 중에 발생하는 석탄 중심의 가스압 특성에 대한 장입탄 수분, 가열속도 및 일반탄 배합비의 영향을 조사하기 위해 이동벽이 있는 pilot 규모의 코크스 오븐(0.45mW$\times$0.1mH$\times$1.2mL)에서 석탄 건류 실험을 수행하였다. 석탄 중심에서의 가열속도가 상업용 코크스 오븐과 비슷한 건류조건에서 장입탄 수분을 감소시켰을 때, 수분 증발 이후 가열속도는 비슷하였으며, 건류 초기 수증기압은 크게 증가하였고, 석탄 중심에서의 가스압은 습탄에 비해 대략 2.5배 증가하였다. 석탄 중심에서의 가열속도가 상업용 코크스 오븐보다 훨씬 빠른 건류조건에서 장입탄 수분을 감소시켰을 때, 수분 증발 이후 가열속도는 크게 감소하였고, 건류 초기 수증기압은 크게 증가하였으며, 석탄중심에서의 가스압은 습탄에 비해 대략 2배 증가하였다. 석탄 가열속도가 상업용 오븐보다 빠른 건류조건에서 장입탄에 일반탄을 첨가하여 일반탄 배합비를 증가시켰을 때 배합탄 중심에서의 가스압은 현저히 감소하였다.

• Polymer(Korea)
• /
• v.24 no.2
• /
• pp.220-227
• /
• 2000

Silica and carbon black filled natural rubber (NR) vulcanizates were prepared with different mixing modes and amounts of fillers. Curing characteristics, morphology. and tear properties of the NR vulcanizates were investigated. The NR vulcanizates filled with silica and carbon black sequentially showed longer induction time ($t_2$), cure index ($t_{90}$ ), and lower maximum torque ($T_{max}$ ) than the NR vulcanizates filled with them simultaneously, during curing process. The former showed superior dispersion of fillers and tear properties to the latter. The NR vulcanizates containing 30 phr of silica showed excellent properties in the experimental range.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.22 no.3
• /
• pp.292-303
• /
• 2002

This paper presents experimental results for early-age properties of concrete such as the setting time and strength, evaluated via the ultrasonic pulse velocity (UPV). Developing and using an automatically-recording monitoring system, the UPV's of mortar and concrete with various water to binder ratios (W/B) were measured during the first 24 hours. In addition, probe penetration and compression tests were conducted to measure the setting time and compressive strength, respectively. It was observed that the UPV's of mortar with high W/B remained constant during the first 6.5 hours and then abruptly began to increase at constant rates. On the other hand, the UPV of mortar with low W/B increased relatively slowly and gradually due to the setting retardation caused by the use of high range water reducing agent (HRWR). It was found that setting of concrete occurs when the UPV reaches a certain value. Moreover, it was concluded that the estimation formulas should incorporate the effects of W/B to more accurately estimate the early-age strength of concrete from the UPV.

• Journal of the Korea Concrete Institute
• /
• v.27 no.4
• /
• pp.419-426
• /
• 2015

The purpose of this study is to investigate experimentally the optimum mix design and site application case of soil mixing wall (SMW) method which is cost-effective technique for construction of walls for cutoff wall and excavation support as well as for ground improvement before constructing LNG storage tank typed under-ground. Considering native soil condition in site, main materials are selected ordinary portland cement, bentonite as a binder slurry and also it is applied $1,833kg/m^3$ as an unit volume weight of native soil, Variations for soil mixing wall are as followings ; (1) water-cement ratio 4cases (2) mixing velocity (rpm) 3levels (3) bleeding capacity and ratio, compressive strength in laboratory and site application test. As test results, bleeding capacity and ratio are decreased in case of decreasing water-cement ratio and increasing mixing velocity. Required compressive strength (1.5 MPa) considering safety factors in site is satisfied with the range of water-cement ratio 150% below, and test results of core strength are higher than those of specimen strength in the range of 8~23% by actual application of element members including outside and inside in site construction work. Therefore, optimum mix design of soil mixing wall is proposed in the range of unit cement $280kg/m^3$, unit bentonite $10kg/m^3$, water-cement ratio 150% and mixing velocity 90rpm and test results of site application case are satisfied with the required properties.

• Elastomers and Composites
• /
• v.40 no.1
• /
• pp.29-36
• /
• 2005

Mixing condition and procedure affect properties or a filled rubber compound such as filler dispersion, viscosity, and bound rubber formation. Influence of separate load of styrene-butadiene rubber (SBR) and acrylonitrile-butadiene rubber (NBR) on properties or silica-filled SBR compounds containing NBR was studied. Cure time and cure rate became faster as NBR content increased. The crosslink density increased with increase in the NBR content. The bound rubber content also increased as the NBR content increased. NBR content of the bound rubber was higher than that of the compounded rubber. The bound rubber content was higher when SBR and NBR were loaded separately than when loading simultaneously. The cure time and cure rate were slower for the separate load than for the simultaneous one. The crosslink density was also lower for the former case than for the latter one.

• Elastomers and Composites
• /
• v.49 no.1
• /
• pp.73-81
• /
• 2014

Friction and wear behaviors of natural rubber(NR) compounds were investigated using a blade-type abrader. The effects of temperature, normal load, and rotation speed on wear rate were studied, and wear behaviors of deteriorated compounds were also evaluated. As the rotation speed of specimen and the normal load to specimen increased, the wear rate increased. However, as the experimental temperature increased, the frictional coefficient decreased and the wear rate decreased accordingly. It was found from the wear studies that a power-law relation works between the frictional work input and the wear rate. It was observed that the wear rate dramatically increased by the degradation of the rubber specimen. The wear pattern was developed and the bigger ridge space of the pattern was observed usually in the higher normal load applied. In determining the wear rate of rubber compound, the continuous measurements of wear distance using the blade-type abrader could be successfully used instead of intermittent measurements of wear-loss weight.

• Elastomers and Composites
• /
• v.48 no.2
• /
• pp.103-113
• /
• 2013

The properties of the rubber composites containing a silane and silica were evaluated by changing the mixing time and temperature, in order to find the optimum mixing conditions. Characteristics of the compounds were evaluated after mixing at $120^{\circ}C$, $140^{\circ}C$, and $160^{\circ}C$ with various mixing time. With increasing of mixing time, mooney viscosity decreased while the bound rubber contents of the compounds increased. Viscosity rise by increased mixing time was bigger at low temperature and the higher the mixing temperature the faster in the formation of bound rubber. With lower mixing temperature of $120^{\circ}C$, cross-linking rate was almost constant. Dynamic viscoelastic properties and dispersity of the compound showed that dispersion of ingredients and reaction was not sufficient with the mixing time of less than 10min. On the contrary, with high temperature, it was obvious that good dynamic and physical properties could be obtained due to sufficient coupling reaction, however it was thought this high temperature is not optimum because of sensitive cross-linking rate and physical properties and excessive formation of bound rubber. Consequently, it was confirmed that the mixing condition of 10min at $140^{\circ}C$ was optimum for the silane coupling reaction and dispersion of functionalized S-SBR containing silica and silane.

• Elastomers and Composites
• /
• v.49 no.2
• /
• pp.149-154
• /
• 2014

Friction and abrasion behaviors were investigated for SBR rubber compounds reinforced by silica and carbon black. Knife-blade abrader, newly designed based on tearing energy theory, was utilized in order to evaluate the effect of frictional work on the wear rate of the rubber compounds. It was found that the power law relation between frictional work and wear rate worked, in which as the wear rate was increased as frictional work increased. The wear rate could be determined successfully using the knife-blade abrader in which a moving distance of the knife blade in the process of wearing was measured continuously, instead of intermittent measurements of weight loss by wear during experiment.

• Elastomers and Composites
• /
• v.35 no.3
• /
• pp.215-226
• /
• 2000

Cure characteristics of carbon black-filled rubber compounds with different rubber composition were studied using a rheometer. The carbon black-filled rubber compounds with single, binary, and ternary rubber compositions of natural rubber (NR), styrene-butadiene rubber (SBR), and butadiene rubber (BR) were used. Delta-torques of the NR/BR- and SBR/BR-based compounds with a high BR content were higher than those of the single rubber-based compounds. For ternary rubber-based compounds, the delta-torques of the compounds were lower when the difference in the rubber content ratios was small than when it was big. Scorch and optimum cure times of the rubber compounds became shorter by increasing the content of NR in the compounds while those became longer by increasing the SBR content. Cure rates of the rubber compounds increased with a decrease of the SBR content in the rubber compounds. Reversion ratios decreased with an increase of the SBR content in the rubber compounds.