• Journal of Energy Engineering
• /
• v.21 no.4
• /
• pp.393-397
• /
• 2012

In this study, an organic Rankine cycle(ORC) for gas engine waste heat recovery for industry has been constructed and a performance analysis test has been carried out. Shell & tube style heat exchanger has been equipped on an engine exhaust manifold in order to absorb heat of engine exhaust gas into the working fluid(refrigerant R134a). Under 60 kW of engine power output, about 63 kW of engine exhaust gas heat was discharged and the proportion of heat recovered was 68~73% while 43~46 kW of heat was absorbed into working fluid. Consequently rated power output of ORC was 4.6 kW while the ratio of rated power output to engine exhaust gas heat was 7.3%.

• Journal of Advanced Navigation Technology
• /
• v.10 no.4
• /
• pp.348-355
• /
• 2006

In this paper, frequency multipliers used S-band transponder of the KOMPSAT 3 are designed and fabricated. In the transponder, 108 times multiplier which generate 1st LO signal(2008.8MHz) is comprised of the X9 frequency multiplier, 1st X2 multiplier, 2nd X2 multiplier and the last stage of the X3 frequency multiplier. As results, output power of 8.17 dBm at 2008.8MHz, the harmonic suppression of -56.67dBc, the bandwidth of 14MHz were measured.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.04a
• /
• pp.19-19
• /
• 1998

최근 화학, 연소, 동력, 제철 등의 각종 플랜트에서 조업압력이 고압화되어 가고 있으며, 이에 수반하여 배관계를 통하는 고압가스 유동에 관한 연구가 활발하게 진행되고 있다. 배관계를 통하는 고압가스의 유동에 있어서 유량의 적절한 제어, 유동에 의하여 야기되는 배관계의 소음·진동, 그리고 배기가스의 적절한 처리법 등은 공학적으로 매우 중요한 문제로 알려져 왔다. 일반적으로 정상운전을 하는 플랜트에서 고압 배기가스의 문제는 배기가스 Expander에 의하여 에너지를 회수하는 방법이 생각될 수 있으나, 실제 공업현장에서는 배기가스를 안전하고, 또 소음·진동을 발생시키지 않도록 적절하게 처리하는 것이 매우 중요한 기술적 과제로 남아 있다. 일반적으로 배기가스의 압력이 임계압력(critical pressure) 이상으로 되는 경우(실제 대부분의 플랜트에서 배기가스의 압력은 임계압력보다 매우 높다), 배관계 내부에서 충격파(shock-wave)가 발생하여 난류와동 혹은 난류경계층과 간섭하게 됨으로써 강력한 공기역학적 소음이나 진동을 발생시키게 된다. 이와 같은 소음·진동에 대한 대책으로는 현재 가스배출부에 감압밸브를 직렬로 설치하거나, 유로에 다공판(porous plates)들을 삽입하여 감압과정을 공간적으로 분산시킴으로써, 충격파가 발생하지 않도록 하는 방법을 주로 채택하고 있다. 그러나 이러한 방법을 적용하는 경우 배기가스 유동에 대한 유량의 제어기능이 저하되는 문제가 발생한다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.583-586
• /
• 2017

Infrared signal measurement are conducted from a micro-turbo jet engine with different nozzle configurations. The conventional cone type, a S-shaped type with aspect ratio 5.2 and five rectangular type nozzle with different aspect ratios are used for this experiment work. The result show that infrared signal from the exhaust gas decrease as the aspect ratio increase. In case of S-shaped nozzle, the maximum infrared signal is reduced about 28.4% when compared of rectangular nozzle with aspect ratio 5(AR5).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.2
• /
• pp.15-20
• /
• 2018

The objective of this study is to numerically investigate the thermal characteristics of an automobile exhaust-based heat exchanger for automotive thermoelectric power generation with various exhaust gas mass flow rates and temperatures. The heat exchanger for automotive thermoelectric power generation has a square-type pin installed inside, so the maximum amount of heat can be transferred to the thermoelectric element from the heat energy coming from the automobile exhaust gas. The exhaust gas mass flow rate changed from 0.01, to 0.02, to 0.03 kg/s, and the exhaust gas temperature changed from 400, to 450, to 500, to 550, to $600^{\circ}C$, respectively. A numerical simulation was conducted by using the commercial program ANSYS CFX v17.0. Consequently, the exhaust gas pressure difference between the inlet and the outlet of the heat exchanger is determined according to the flow rate of the exhaust gas. When the mass flow rate of the exhaust gas increased, the pressure difference between the inlet and the outlet of the heat exchanger increased, but the exhaust gas pressure difference between the inlet of the heat exchanger and the outlet did not vary with the exhaust gas temperature. Therefore, in order to obtain the maximum surface temperature from the heat exchanger, the exhaust gas mass flow rate should be lower, and the exhaust gas temperature should be higher.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.206-206
• /
• 2012

초고진공 시스템에 사용되는 조합펌프(게터펌프+이온펌프)의 배기속도를 측정하여 보고한다. 이 펌프는 좁은 공간 내에 설치가능 하고 비교적 큰 배기속도를 가지도록 설계되었다. 이온펌프는 소형(30 l/s) 이극형이며 게터펌프는 ZrVFe 합금의 모듈형태로 1개에서 3개까지 장착되도록 하였다. 이 펌프의 설계 성능을 검증하기 위하여 초고진공상태의 잔류기체 구성비에 가까운 기체조성비(수소 90%, 일산화탄소 10%)로 그 배기속도를 측정하였다. 배기속도는 미국진공학회 표준측정순서를 따랐으며 도달압력도 측정하여 보고한다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.1
• /
• pp.37-44
• /
• 2001

This study is focused on the development of a new muffler. A control valve installed in the exhaust system is operated by torsion springs, and its open angle is controlled automatically corresponding to the engine operating conditions. The experiments were done using an exhaust system simulator having the same pulsation wave frequency and similar pulsation propagation characteristics of a real exhaust system. The purpose of this study is to develop a new muffler system which has improved noise reduction quality and less power loss than conventional mufflers and electronic-control mufflers.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.6
• /
• pp.779-785
• /
• 2011

Prediction of the transient pressure variations and performance parameters has been carried out for an SI engine using one of commercial software, GT-POWER. Various models were applied for the calculation of properties of the plenum chamber, exhaust manifold and catalytic convertor which are very important components included in the intake and exhaust systems.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.34-34
• /
• 2011

본 논문에서는 반도체의 제조공정 중 작동되는 건식 전공펌프에서 측정한 다중변수들의 통계적, 물리적 특성을 소개한다. 흡기부 및 배기부 압력과 부스터/드라이펌프의 소비전류와 같은 상태변수의 변위 분포는 2개 이상의 특징적인 구간으로 나뉘는 특성을 가지고 있다. 특히 흡기부 압력 데이터는 펌프의 성능상태를 직접적으로 나타내는 배기 속도를 유추할 수 있는 특성을 내포하고 있다. 이러한 관측을 통해 발견한 통계학적 특성을 나타내기 위해 적응형 인자모델(APM)을 이용한 진공펌프 시스템의 실시간 진단 기법을 개발하였다. 동시에 공정 중에 배기속도를 유추 할 수 있는 배기속도지표(PSI)를 제안하여 펌프의 성능 상태를 간접적인 방법으로 관찰하는 기법을 개발하여, 두 기법을 통한 진공펌프 시스템의 상태변화 진단 결과의 경향이 동일함을 확인하였다.

• Journal of Energy Engineering
• /
• v.23 no.3
• /
• pp.51-57
• /
• 2014

A MILD(Moderate and Intense Low oxygen Dilution) combustion, which is effective in the reduction of NOx, is considerably affected by the recirculation flow position of hot exhaust gas to the combustion furnace. A numerical analysis was accomplished to elucidate the flow characteristics in the MILD combustion incinerator for several cases with or without exhaust gas recirculation. It could be seen from the result of the present numerical study that the flow recirculation could be observed in the upper region over the vertical dividing wall for the case without exhaust gas recirculation. The optimal position of exhaust gas recirculation position was derived by the comparison of %RMS of x directional velocity for the cases with exhaust gas recirculation. The case with the exhaust gas recirculation position at the upper right of free board was the most effective with the smallest value of 57.4% RMS.